National Instruments SCXI-1345 Bedienungsanleitung



NATIONAL

INSTRUMENTS®

The Software is the Instrument

Installation Guide

SCXI-1345 Shielded Cable

This guide describes how to install the SCXI-1345 shielded cable with an adapter board between

an SCXI module and a data acquisition board. In addition to the SCXI-1345 kit contents, you

will also need an SCXI chassis, an SCXI module, a computer, a multifunction I/O (MIO) board,

a small Phillips-head screwdriver, and a small flathead screwdriver.

Introduction

With the SCXI-1345 shielded cable, you can make a low-noise, long-distance connection

between your SCXI chassis and your MIO board. You can use the SCXI-1345 with the

following MIO boards:

PC/XT, PC AT Macintosh

AT-MIO-16 NB-MIO-16

AT-MIO-16F-5 NB-MIO-16X

AT-MIO-16X

The SCXI-1345 shielded cable consists of a 1, 2, 5, or 10 m round cable that has a 50-pin female

connector with a grounding strap at one end and a 68-pin female connector at the other end.

When plugged into the SCXI-1345 adapter board, the shielded cable brings the pinout of the

MIO board I/O connector to the SCXI module and to a breakout connector you can use with

other SCXI accessories, such as the SCXI-1180 and the SCXI-1351.

What Your Kit Should Contain

The SCXI-1345 shielded cable kit is available in four cable sizes: 1, 2, 5, or 10 m.

In addition, each version of the kit contains the following components:

¥ Cable adapter assembly

¥ Two small screws

¥ Replacement bracket for AT-MIO-16 boards

¥ Replacement bracket for NB-MIO-16 boards

¥ Two cable tie wraps

¥SCXI-1345 Shielded Cable Installation Guide

If your kit is missing any of the components, contact National Instruments.

Installation Procedure

Figure 1 illustrates the components of your SCXI system and how to connect them.

SCXI Module

Adapter

Board

Step 3 Step 4

Step 7

Shielded Cable

Grounding Strap

Step 8

Step 9

MIO Data Acquisition Board

Figure 1. Connecting the SCXI-1345 to Your MIO Board and SCXI Module

Perform the following steps to install the SCXI-1345 cable:

1. Turn off the power to your computer and the SCXI chassis.

2. Install your SCXI module in the SCXI chassis, following the instructions in your module

user manual.

3. Plug the socket connector of the SCXI-1345 adapter board into the rear signal connector of

the SCXI module.

4. Secure the SCXI-1345 adapter board by screwing the two screws through the rear panel of

the adapter board and into the threaded strips in the rear of the SCXI chassis.

5. Replace the bracket of your MIO board with the appropriate bracket from the SCXI-1345

cable kit, unless your MIO board has a bracket with a grounding strap tab.

a. Remove your MIO board from your computer.

b. Unscrew and remove the two screws that attach the bracket to the MIO board.

c. Remove the bracket from the board. See Figure 2 for NB board bracket removal or

Figure 3 for AT board bracket removal.

Step c

Step b

Bracket

NB MIO Board

Figure 2. Removing the Bracket from an NB Board

Step c

Step b

AT MIO

Board

Bracket

Figure 3. Removing the Bracket from an AT Board

d. The 50-position I/O connector on your MIO board may have small plastic key inserts

installed for mating with military polarized connectors. Because these keys are not

compatible with the 50-position connector on the SCXI-1345, you must remove them.

The 50-position SCXI-1345 connector has a center polarization bump that prevents you

from inserting the connector upside down.

To remove the key inserts, use a thin probe such as a pencil or pen tip to gently press

down on the release tab in the center of the key insert (see Figure 4). Then use the

probe to lift up the back end of the key insert and slide the insert off the connector.

MIO Board

Figure 4. Removing the Key Inserts

e. Identify the proper replacement bracket from your kit. If you have an NB Series board,

use the bracket marked 745402-01; if you have an AT Series board, use the bracket

marked 745403-01. The bracket that you use should look like the one you remove,

except that the new one has an extra tab that attaches to the grounding strap.

f. Install the new bracket by aligning the bracket with the holes in your MIO board and

screw in the two mounting screws.

6. Install your MIO board in a slot in your computer, following the instructions in your MIO

board user manual.

7. Connect the 68-pin connector (the end without the grounding strap) of the SCXI-1345

cable to the 68-pin connector of the SCXI-1345 adapter board as shown in Figure 5.

Adapter

Board

Shielded Cable

Figure 5. Cable to Adapter Board Connection

8. Connect the 50-pin connector (the end with the grounding strap) of the cable to the I/O

connector on the MIO board as shown in Figure 6.

Shielded Cable

Grounding Strap

Step 8

Step 9

MIO Data Acquisition Board

Figure 6. Cable to I/O Connector Connection

9. Slide the end lug of the ground strap onto the tab of the MIO bracket.

10. Secure the cable to a fixed object with the tie wraps to relieve the strain on the cable.

Strain relief is needed because the SCXI-1345 shielded cable is considerably stiffer than

ribbon cable. The cable connector also has a long stiff backshell that can exert leverage on

the MIO board connector.

The finished installation should look like Figure 7.

Computer

SCXI-1345

Shielded Cable

SCXI

Chassis

Figure 7. Installed Cable

Grounding Considerations

The SCXI-1345 cable has an outer shield, which is grounded to the SCXI chassis at one end

when you connect the SCXI-1345 cable to the chassis. The other end of the cable terminates in a

grounding strap that provides shielding for the MIO board when connected. You do not have to

connect the grounding strap for the system to function; however, connecting the grounding strap

improves the electrostatic discharge immunity of the SCXI system, reduces electromagnetic

interference, and shields the analog signals from noise. National Instruments recommends that

you connect the grounding strap. On the other hand, connecting the grounding strap may

increase the ground current flowing between the SCXI system and the computer, thus increasing

the noise in some applications. Laboratory tests with the grounding strap connected produced

less noise, but you can try it both ways and decide which way works better for your application.

If you leave the grounding strap unconnected, secure it to the cable with a tie wrap so that the

strap does not dangle and brush against the exposed pins of another connector at the back of your

computer.

SCXI-1345 Shielded Cable Assembly Pin Translations

The SCXI-1345 cable assembly ties pins 1 and 2 (AIGND) of the MIO board I/O connector

together and ties pins 24 and 33 (DGND) of the MIO board I/O connector together. Do not use

the SCXI-1345 cable assembly with any data acquisition board other than an MIO-16. All other

numbered pins only connect to the same pin number on all three connectors.

Inhaltsverzeichnis

Andere National Instruments Kabel und Steckverbinder Handbücher

National Instruments

National Instruments IMAQ D100 Bedienungsanleitung

National Instruments

National Instruments NI SHC68 Bedienungsanleitung

National Instruments

National Instruments SH6850 Bedienungsanleitung

National Instruments

National Instruments 9212 Handbuch

National Instruments

National Instruments IMAQ SCB-100 Bedienungsanleitung

National Instruments

National Instruments SCXI-1353 Bedienungsanleitung

National Instruments

National Instruments SCXI-1342 PC-LPM-16 Bedienungsanleitung

National Instruments

National Instruments IMAQ A8020 Bedienungsanleitung

National Instruments

National Instruments PXI-1042HVDC Bedienungsanleitung

National Instruments

National Instruments SH160DIN-3XDB50F Bedienungsanleitung

National Instruments

National Instruments CB-27 Bedienungsanleitung

National Instruments

National Instruments SCXI-1356 Bedienungsanleitung

National Instruments

National Instruments SH160DIN-4XDB50F-2A Bedienungsanleitung

National Instruments

National Instruments NI-XNET LIN Bedienungsanleitung

National Instruments

National Instruments SCXI-1355 Bedienungsanleitung

National Instruments

National Instruments BNC-2120 Bedienungsanleitung

National Instruments

National Instruments IMAQ D100DAL Bedienungsanleitung

National Instruments

National Instruments CB-50 Bedienungsanleitung

National Instruments

National Instruments SCB-12 Bedienungsanleitung

National Instruments

National Instruments IMAQ A2514 Bedienungsanleitung

National Instruments

National Instruments PXI-1031DC Bedienungsanleitung

National Instruments

National Instruments NI-XNET CAN HS/FD Bedienungsanleitung

National Instruments

National Instruments IMAQ SCB-100 Bedienungsanleitung

National Instruments

National Instruments CB-27 Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung