National Instruments NI DCM-2316 Bedienungsanleitung

GETTING STARTED GUIDE

NI DCM-2316

Embedded Direct Injector Control and Measurement (DCM) Device

with Real-Time Processor and Reconfigurable FPGA

Hazardous Voltage This device sources hazardous voltages up to 250V. You must

take the following precautions. A hazardous voltage is a voltage greater than 42.4

Vpk voltage or 60 VDC to earth ground.

Caution Ensure that hazardous voltage wiring is performed only by qualified

personnel adhering to local electrical standards.

Caution Do not mix hazardous voltage circuits and human-accessible circuits in

the same cable unless the cables are properly insulated for min. 250V.

Caution Ensure that devices and circuits connected to the module are properly

insulated from human contact.

Caution Except for the isolated RS232, CAN, IGND, IO Lock terminals, and the

Ethernet Port, all I/O terminals are hazardous voltage LIVE (> 42.4 Vpk/60 VDC) or

could be at hazardous potential. You must ensure that devices and circuits connected

to the module are properly insulated from human contact. External protection must

be provided to protect any other devices connected to the BATT, DRVP, and MPRD

supplies.

2|ni.com |NI DCM-2316 Getting Started Guide

Caution Do not operate the DCM in a manner not specified in this document.

Product misuse can result in a hazard. You can compromise the safety protection built

into the product if the product is damaged in any way. If the product is damaged,

return it to NI for repair.

Caution Do not disconnect the power supply wires and connectors from the

controller unless power has been switched off.

About This Manual

This document explains how to begin using the National Instruments DCM family of devices.

The scope is limited to focus on initial DCM startup and basic operation using the DCM Starter

Harness and DSI software. For more detailed information on DCM hardware or software, refer

to the Related Documentation section of this guide.

Preparing the Environment

Ensure that the environment in which you are using the DCM meets the following specifications.

Note Refer to the device specifications on ni.com/manuals for complete

specifications.

Identifying the Hardware

The following section includes identification of DCM kit contents and all other required

components.

Verifying Kit Contents

Verify that the following item(s) are included in the DCM kit:

• DCM with rack-mount end plates

• NI DCM Getting Started Guide

• NI DCM-2316 Specifications Guide

Required Components (Not Included)

The following items are necessary to set up and use the NI DCM using this document:

• Host/Development PC running Windows 7/8.1/10

Operating temperature

(IEC 60068-2-1, IEC 60068-2-2)

0 °C to 55°C

Operating humidity (IEC 60068-2-56) 10% RH to 90% RH, non-condensing

Pollution Degree (IEC 60664) 2

Maximum altitude 2,000 m

NI DCM-2316 Getting Started Guide |© National Instruments |3

• DCM Starter Harness kit

• Piezo or Solenoid Injector

• 12 V or 24 V DC power supply, 180 W1minimum DC power supply

Software Installation

The DCM may be used with several different software personalities. Each personality requires

different software packages to be installed on the host computer which may need to be

individually licensed.

NI Powertrain Controls supports the following software personalities for the DCM:

• DCM Default Software Image (DSI)

• NI LabVIEW

•NIVeriStand

DCM Default Software Image (DSI)

Before using the DCM DSI, you must install the following application software and device

drivers on the host computer in this order:

• NI CompactRIO Device Drivers 16.0 or later

• Software Calibration Management (SCM) Toolkit 2016 or later (evaluation license)

Note The DCM is shipped supporting the latest version of SCM. If you have

trouble launching the DCM DSI with the latest available version of SCM on ni.com,

the software on your DCM may need to be updated. Refer to the NI DCM-23XX DSI

User Guide for more information.

For minimum software support information, visit ni.com/info and enter the Info Code

swsupport.

DCM With LabVIEW

Before using the DCM with LabVIEW, you must install the following application software and

device drivers on the host computer in this order:

• LabVIEW 2016 or later

• LabVIEW Real-Time Module 2016 or later

• LabVIEW FPGA Module 2016 or later

• NI CompactRIO Device Drivers 16.0 or later

• NI Powertrain Controls Device Drivers 2.160.0.0 or later

1 Minimum power supply requirements assume basic operation; actual power supply

requirements will vary depending on hardware and software configuration.

4|ni.com |NI DCM-2316 Getting Started Guide

The NI Powertrain Controls Device drivers may be installed using JKI Software’s VI Package

Manager. For minimum software support information, visit ni.com/info and enter the Info

Code swsupport.

DCM With VeriStand

Before using the DCM with VeriStand, you must install the following application software and

device drivers on the host computer in this order:

• VeriStand 2016 or later

• NI DAQmx 16.0 or later

• NI VISA 16.0 or later

• NI CompactRIO Device Drivers 16.0 or later

• NI Powertrain Controls DCM Custom Device for NI VeriStand

For minimum software support information, visit ni.com/info and enter the Info Code

swsupport.

Hardware Installation

Mounting the DCM

The DCM is designed to be flexible in its mounting position. The following mounting methods

are supported by NI Powertrain Controls:

•Rack-mount: Rack-mounted in a standard 19-in. chassis, 5U

– Requires: Rack-mount kit (included, PN: 785246-01)

•Panel-mount: Firmly secured on a clean, flat surface with connector facing out or up

– Requires: Panel mount kit (optional, PN: 785247-01)

Connecting the DCM Chassis Ground Lug to Facility

Ground

You must connect the DCM chassis ground lug to the grounding electrode system of the facility.

What to Use

• Wire, 1.63 mm2(14 AWG) or larger, or braided grounding strap

• Screwdriver, flat 3/16-in.

What to Do

Complete the following steps to ground the DCM.

1. Remove the screw from the chassis ground lug on the DCM.

2. Insert wire or braided grounding strap into the side of the chassis ground lug

3. Tighten the grounding screw to 1.4 N · m (12 lb · in.) of torque.

NI DCM-2316 Getting Started Guide |© National Instruments |5

4. Attach the other end of the wire to the grounding electrode system of your facility using a

method that is appropriate for your application.

For more information about ground connections, visit ni.com/info and enter the Info Code

emcground.

Connecting the DCM Starter Harness

The DCM Starter Harness contains all connections required to begin using the DCM with

one solenoid injector and one piezo injector. The DCM Starter Harness should connect with

the devices as shown in Figure 1.

What to Use

• DCM Starter Harness

•HexDriver,4mm

• PDU-2300

• Emergency Stop (E-Stop)

• Solenoid and Piezo injectors or dummy loads

What to Do

Complete the following steps to connect the DCM Starter Harness.

1. Ensure that the PDU is disconnected from all power sources.

2. Connect the harness to DCM Connector 1, being sure to orient the connector appropriately.

3. Tighten the DCM connector terminal fastener to 5 N · m (44 lb · in.) of torque using a 4 mm

Hex Driver.

4. Ensure your PDU is correctly configured for 12 V or 24 V, whichever is used. Refer to the

Configuring the PDU-2300 section for more information.

5. Connect the harness to the PDU (blue connector).

6. Connect the harness to the emergency stop.

7. Connect Solenoid A1 injector (real or dummy).

8. Connect Piezo A2 injector (real or dummy).

6|ni.com |NI DCM-2316 Getting Started Guide

Figure 1. DCM Starter Harness Connections

Note Many I/O terminals come unpopulated in the DCM Starter Harness kit. These

connections must be populated by the user in order for the relevant functions to be

used. For more information about wiring additional I/O, refer to the NI DCM User

Guide.

Configuring the PDU-2300

The PDU-2300 may be configured for 12 V or 24 V systems. The PDU ships configured for 12 V

systems by default. Complete the following steps to configure the PDU for 24 V systems. See

Figure 2 below for illustration of fuse placement for 12 V and 24 V setup.

1. Open the PDU cover to expose the various relays and fuses.

2. Remove 7.5 A fuses from slots F12 and F13 and set aside.

3. Fill slot F14 (empty by default) with one of the 7.5 A fuses removed in the previous step.

4. Save the remaining fuse as a replacement.

1 PDU-2300 5 Heavy-duty power supply cables

2 Light-duty power supply cables 6 Injector dummy loads and adapter

3 Power supply 7 Emergency stop

4 DCM 8 RS232

NI DCM-2316 Getting Started Guide |© National Instruments |7

Caution Damage may occur if the PDU-2300 is not appropriately configured for

the selected supply voltage before connecting power.

Figure 2. Fuse Placement for 12 V and 24 V Setup

Connecting the DCM to Power

Powering the DCM with the DCM Starter Harness kit requires a 12 V or 24 V, 180 W minimum,

external DC power supply. Recommended power supplies are listed in Table 1 below. The

light-duty power supply leads (14 AWG) included in the DCM Starter Harness kit are

recommended only for bench-top applications which require less than 15 A of current. The

heavy-duty leads (8 AWG) included in the DCM Starter Harness kit are recommended for all

other applications.

What to Use

• Starter harness light-duty (<15A) or heavy-duty power supply leads

• Wrench, 1/2-in.

• NI recommended power supply

Table 1. Recommended Power Supplies

Power Supply Part Number

PULS QS10.121 Power Supply

(12 VDC, 15 A, 100-240 VAC/110-150 VDC Input)

783168-01

NI PS-17 Industrial Power Supply

(24 VDC, 20 A, 100-240 VAC/110-150 VDC Input)

781095-01

Tripp Lite PR 60

(13.8 VDC, 60 A, 120 VAC Input)

PR 60

TDK Lambda Genesys 1500W

(0-30 VDC Variable, 0-50 A Variable, 85-265 VAC input)

GEN 30-50

12 V Setup

F12

7.5 A Fuse

F14

Empty

F13

7.5 A Fuse

24 V Setup

F12

Empty

F14

7.5 A Fuse

F13

Empty

8|ni.com |NI DCM-2316 Getting Started Guide

What to Do

Complete the following steps to connect power to the DCM.

• Ensure the DCM Starter Harness is connected as discussed in the Connecting the DCM

Starter Harness section.

• Connect power supply leads terminated with properly rated ring terminals to the PDU

Positive (+) and Negative (-) input studs.

• Tighten terminal fasteners to 10.2 N · m (90 lb · in.) using a 1/2-in. wrench.

• Connect power supply leads to the power supply. If connecting to a battery, always connect

the Negative (-) lead last. When disconnecting the battery, always disconnect the

Negative (-) lead first.

Connecting the DCM to the Host Computer

Complete the following steps to connect the DCM to the host computer or Ethernet network

using the RJ-45 Gigabit Ethernet port.

• Power on the host computer or Ethernet hub.

• Connect the RJ-45 Gigabit Ethernet port on the DCM to the host computer or Ethernet hub

using a standard Category 5 (CAT-5) or better shielded, twisted-pair Ethernet cable.

Caution To prevent data loss and to maintain the integrity of your Ethernet

installation, do not use a cable longer than 100 m (328 ft).

Note The DCM attempts to initiate a DHCP network connection the first time you

connect using Ethernet. The DCM connects to the network with a link-local IP

address with the form 169.254.x.x if it is unable to initiate a DHCP connection.

Powering on the DCM

When you power on the DCM for the first time, the device boots DCM DSI. The POWER LED

illuminates, the STATUS LED illuminates briefly, and then the USER1 LED blinks steadily

once the DSI executable has booted. Overall boot time is approximately 60 seconds.

Configuring the DCM in Measurement and

Automation Explorer (MAX)

Complete the following steps to find your DCM in MAX.

• Ensure that any anti-virus or firewall software running on the host computer allows

connections to the host computer.

Note MAX uses UDP 44525. Refer to the documentation of your firewall software

for information about configuring the firewall to allow communication through

UDP 44525.

• Launch MAX on the host computer.

NI DCM-2316 Getting Started Guide |© National Instruments |9

• Expand Remote Systems in the configuration tree and location your system.

• Select your target.

Tip When DSI is installed on a DCM, MAX lists the system under the model

number followed by the serial number, such as NI-DCM-2316-1856AAA. If the

DCM is formatted without the DSI image, MAX lists the system using the format

NI-sbRIO-9651-1856AAA.

Setting a System Password

Complete the following steps to set a system password.

Note The default username for the DCM is admin. There is no default password

for the DCM, so you must leave the password field blank when logging in until you

set a system password.

1. Right-click your system and select Web Configuration.

Note The NI Web-Based Configuration and Monitoring utility opens in your

default browser and is where you set the password. If you have not installed

Microsoft Silverlight, NI Web-based Configuration & Monitoring prompts you

to do so.

2. Enter a unique name for your system in the Hostname field.

3. Click the Security Configuration icon.

4. Click Login.

5. In the Login dialog box, enter the username admin and leave the password field blank.

6. Click OK.

7. Click Change Password.

8. Enter and re-enter a new password.

9. Click OK.

10. Click Save.

11. Click OK to confirm you are changing the password.

Caution NI cannot recover lost system passwords. If you forget the password, you

must contact NI and reformat the controller.

10 |ni.com |NI DCM-2316 Getting Started Guide

Installing Software on the DCM (LabVIEW or VeriStand

Personalities)

Complete the following steps to install software on the DCM for LabVIEW or VeriStand

personalities. If using DCM DSI, skip this section.

Note The DCM ships with the DSI pre-installed. In order to run non-DSI

personalities, the DCM must be formatted. To reinstall the DCM DSI after

formatting, refer to the NI DCM-23XX DSI User’s Manual for more information.

1. In MAX, right-click on your DCM target under Remote Systems.

Caution Any files, including calibrations, present on the DCM during formatting

will be lost. Prior to formatting, any files present on the DCM must be backed up in

order to be saved. Files may be copied from the DCM by WebDAV file transfer.

a. Select Format Disk.

Tip You must log in if you set a system password.

b. Select Attempt to restart into safe mode.

c. Select the desired option to manage network adapter settings.

d. Click Format.

e. Wait for the formatting process to finish, then click OK.

2. In MAX, expand your system under Remote Systems.

a. Right-click Software.

b. Select Add/Remove Software to launch the LabVIEW Real-Time Software Wizard.

Tip You must log in if you set a system password.

c. Select the recommended software set for your LabVIEW and NI-RIO Device Drivers

versions.

d. Click Next.

e. Verify that the summary of software to install is correct.

f. Click Next.

g. Click Finish when the installation is complete.

3. To install NI VeriStand or NI SCM on the target, continue with the following steps.

a. In MAX, right-click Software as before.

b. Select Add/Remove Software to launch the LabVIEW Real-Time Software Wizard.

Tip You must log in if you set a system password.

Inhaltsverzeichnis

Andere National Instruments Steuereinheit Handbücher

National Instruments

National Instruments NI 9262 Bedienungsanleitung

National Instruments

National Instruments NI-SPEEDY-33 Bedienungsanleitung

National Instruments

National Instruments SCXI-1000 Bedienungsanleitung

National Instruments

National Instruments NI 9211 Bedienungsanleitung

National Instruments

National Instruments LabVIEW Robotics Module Bedienungsanleitung

National Instruments

National Instruments 9220 Handbuch

National Instruments

National Instruments NI 9269 Bedienungsanleitung

National Instruments

National Instruments PXIe-6595 Bedienungsanleitung

National Instruments

National Instruments sbRIO-9651 Leitfaden

National Instruments

National Instruments PXI-2503 Bedienungsanleitung

National Instruments

National Instruments PXI-6682 Series Bedienungsanleitung

National Instruments

National Instruments NI 9209 Handbuch

National Instruments

National Instruments 9755 Bedienungsanleitung

National Instruments

National Instruments NI 9242 Bedienungsanleitung

National Instruments

National Instruments 9235 Handbuch

National Instruments

National Instruments NI 9225 Handbuch

National Instruments

National Instruments SLSC-12251 Bedienungsanleitung

National Instruments

National Instruments NI 9478 Bedienungsanleitung

National Instruments

National Instruments SCC-LP Series Bedienungsanleitung

National Instruments

National Instruments 9477 Bedienungsanleitung

National Instruments

National Instruments FieldPoint cFP-DI-304 Bedienungsanleitung

National Instruments

National Instruments NI 9802 Bedienungsanleitung

National Instruments

National Instruments NI 9871 Bedienungsanleitung

National Instruments

National Instruments 7340 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung