National Instruments NI-488.2 Bedienungsanleitung

October 2003

323735A-01

INSTALLATION GUIDE

Installing Your SB-GPIB/TNT

and NI-488.2 for Solaris

This document describes how to install NI-488.2 for Solaris and the

SB-GPIB/TNT or SB-GPIB into your Sun SPARC system. The NI-488.2

software included in this kit is intended for use with Sun SPARC systems

running Solaris 2.6 or later.

Other documentation, including the software reference manual, is available

on your NI-488.2 software for Solaris CD in the \documentation folder.

™

Installing Your SB-GPIB/TNT and NI-488.2 for Solaris 2 ni.com

Installing the GPIB Hardware

Before you install your GPIB controller, consult the manual that came with your

workstation for specific instructions and warnings. You must have superuser

privileges to install the hardware and software.

Caution Electrostatic discharge can damage several components on

your GPIB board. To avoid electrostatic damage when you handle the

module, touch the antistatic plastic package to a metal part of your

computer chassis before you remove the board from the package.

Complete the following steps to install the GPIB board.

1. Log on as superuser. To become a superuser, type su root and enter the root

password.

2. Shut down your system by typing the following commands at the command

line prompt:

sync; shutdown

3. Power off your computer after it has shut down. Keep the computer plugged

in so that it remains grounded while you install the GPIB board.

4. Remove the top cover of the system unit.

5. Remove the GPIB connector extender (if your board came with one) by

loosening the thumbscrews.

6. Find an unused DVMA master slot in your computer.

7. Insert the GPIB board into the slot with the GPIB connector sticking out of the

opening on the back panel, as shown in Figure 1. Do not insert the board into

a slave-only physical slot if you are using DVMA; only programmed I/O

transfers are possible in slave-only slots. Refer to the documentation for your

Sun SPARC system for information about DVMA master and DVMA slave

slots.

8. Replace the system unit cover.

9. Reinstall the GPIB connector extender you removed in step 5 if you have

problems connecting the GPIB cable to the connector on the board due to

space restraints.

10. Power on your computer. The GPIB interface board is now installed.

Installing Your SB-GPIB/TNT and NI-488.2 for Solaris 4 ni.com

Figure 1. Installing the SB-GPIB/TNT or SB-GPIB

1Slot1

2Slot2

3 Back Panel Rail

4 Backplate Adapter

KEY KEY

J1J2

1 2 3

Installing NI-488.2

Complete the following steps to install NI-488.2 for Solaris.

1. Insert the NI-488.2 for Solaris installation CD.

2. You must have superuser privilege before you can install NI-488.2 for Solaris.

If you are not already a superuser, type su root and enter the root password.

3. Add NI-488.2 to the operating system by entering the following command.

a. On Solaris 2.6 or later versions, the CD automatically mounts as soon as

you insert the CD. If this feature is disabled on your workstation, you must

mount the CD by typing the following command:

/usr/sbin/mount -o ro -F hsfs /dev/dsk/c0t6d0s2 /cdrom/cdrom0

b. Enter the following command to add NI-488.2 to your system:

/usr/sbin/pkgadd -d /cdrom/cdrom0 NICsbgpib

4. Follow the instructions on your screen to complete the installation.

Configuring the Software with ibconf (Optional)

ibconf is an interactive utility you can use to examine or modify the

configuration of the driver. You might want to run ibconf to change the settings

of the software parameters. You must have superuser privilege to run ibconf.

ibconf is largely self explanatory and contains help screens that explain all

commands and options. For more information on using ibconf, refer to the

NI-488.2M Software Reference Manual.

Installing Your SB-GPIB/TNT and NI-488.2 for Solaris 6 ni.com

Complete the following steps to change the default parameters of your NI-488.2

software. The driver should not be in use while you run ibconf.

1. Log on as superuser (root).

2. Type the following command to start ibconf:

ibconf

After you have installed and configured the software, you should verify

the installation. Refer to the Installation Verification section.

Removing NI-488.2 (Optional)

If you ever decide to stop using your GPIB board, you can remove NI-488.2 from

your system. To remove NI-488.2 from the kernel configuration, you must have

superuser privilege and the driver must not be in use. Enter the following

command to unload the software:

pkgrm NICsbgpib

Installation Verification

The software installation test ibtsta verifies that the driver is installed correctly.

It checks for correct access to the device driver.

Run ibtsta by entering the following command:

ibtsta

If no error occurs in ibtsta, NI-488.2 is installed correctly.

If ibtsta fails, it displays an error message that explains why the test failed and

how you can correct the problem. If you are unable to run ibtsta successfully

after you have followed the on-screen instructions, refer to the Common Questions

section.

Using NI-488.2 with Solaris

This section helps you get started with NI-488.2 for Solaris.

Introduction to ibic

The NI-488.2 software includes the Interface Bus Interactive Control utility, ibic.

You can use ibic to enter NI-488 functions and IEEE 488.2-style functions (also

known as NI-488.2 routines) interactively and display the results of the function

calls automatically. Without writing an application, you can use ibic to do the

following:

• Verify GPIB communication with your device quickly and easily

• Become familiar with the commands of your device

• Receive data from your GPIB device

• Learn new NI-488.2 functions and routines before integrating them into your

application

• Troubleshoot problems with your application

• Enter the following command to run ibic:

ibic

• For more information about ibic, refer to Chapter 6, ibic, of the NI-488.2M

Software Reference Manual.

Installing Your SB-GPIB/TNT and NI-488.2 for Solaris 8 ni.com

Programming Considerations

Depending on the programming language you use to develop your application,

you must include certain files, statements, or global variables at the beginning of

your application. For example, you must include the header file sys/ugpib.h in

your source code if you are using C/C++.

You must link the language interface library with your compiled source code. Link

the GPIB C language interface library using one of the following commands,

where example.c is your application name:

cc example.c -lgpib

cc example.c -dy -lgpib

cc example.c -dn -lgpib

-dy specifies dynamic linking, which is the default method. It links the application

to libgpib.so. -dn specifies static linking in the link editor. It links the

application to libgpib.a. For more information about compiling and linking,

refer to the man pages for cc and ld.

For information about each NI-488 function and IEEE 488.2-style function,

choosing a programming method, developing your application, or compiling

and linking, refer to the NI-488.2M Software Reference Manual.

Common Questions

What is wrong if ibfind returns a –1?

The driver may not be installed correctly, or the nodes may not have been created

when the driver was loaded. Try removing and reinstalling NI-488.2 from the

CD-ROM.

Also, the file may require read/write privileges you do not have, or you may have

renamed a device. Make sure that the device names in your application program

match the device names in ibconf.

What information should I have before I call National Instruments?

Please have the results of the diagnostic test ibtsta. You also should have run

ibic to try to find the source of your problem.

Does this driver work with 64-bit Solaris?

Yes. NI-488.2 for Solaris works with either 32-bit or 64-bit Solaris. You also can

create 32-bit or 64-bit applications. The driver installs both 32-bit and 64-bit

language interface libraries on the system. For information on using the NI-488.2

language interfaces, refer to the Using NI-488.2 with Solaris section of this

document.

Installing Your SB-GPIB/TNT and NI-488.2 for Solaris 10 ni.com

Technical Support and Professional Services

Visit the following sections of the National Instruments Web site at ni.com for

technical support and professional services:

•Support—Online technical support resources include the following:

–Self-Help Resources—For immediate answers and solutions, visit our

extensive library of technical support resources available in English,

Japanese, and Spanish at ni.com/support. These resources are

available for most products at no cost to registered users and include

software drivers and updates, a KnowledgeBase, product manuals,

step-by-step troubleshooting wizards, conformity documentation,

example code, tutorials and application notes, instrument drivers,

discussion forums, a measurement glossary, and so on.

–Assisted Support Options—Contact NI engineers and other

measurement and automation professionals by visiting

ni.com/support. Our online system helps you define your question

and connects you to the experts by phone, discussion forum, or email.

•Training—Visit ni.com/training for self-paced tutorials, videos, and

interactive CDs. You also can register for instructor-led, hands-on courses

at locations around the world.

•System Integration—If you have time constraints, limited in-house technical

resources, or other project challenges, NI Alliance Program members can

help. To learn more, call your local NI office or visit ni.com/alliance.

•Declaration of Conformity (DoC)—A DoC is our claim of compliance

with the Council of the European Communities using the manufacturer’s

declaration of conformity. This system affords the user protection for

Andere Handbücher für NI-488.2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Instruments Controller Handbücher

National Instruments

National Instruments NI PXIe-8880 Bedienungsanleitung

National Instruments

National Instruments PCI-7330 Bedienungsanleitung

National Instruments

National Instruments NI SCXI 1357 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-8133 Bedienungsanleitung

National Instruments

National Instruments cRIO-FRC II Bedienungsanleitung

National Instruments

National Instruments cDAQ-9132 Bedienungsanleitung

National Instruments

National Instruments cRIO-9038 Bedienungsanleitung

National Instruments

National Instruments Eight-slot USB Chassis NI cDAQ-9172 Handbuch

National Instruments

National Instruments PXI-8195 Bedienungsanleitung

National Instruments

National Instruments CompactRIO cRIO-9002 Bedienungsanleitung

National Instruments

National Instruments ExpressCard-8360 Bedienungsanleitung

National Instruments

National Instruments cDAQ-9139 Bedienungsanleitung

National Instruments

National Instruments NI 7340 Bedienungsanleitung

National Instruments

National Instruments cRIO-9032 Bedienungsanleitung

National Instruments

National Instruments FW-7344 Gebrauchsanweisung

National Instruments

National Instruments cRIO-9033 Bedienungsanleitung

National Instruments

National Instruments CompactRIO cRIO-9072 Bedienungsanleitung

National Instruments

National Instruments sbRIO-9607 Bedienungsanleitung

National Instruments

National Instruments CompactRIO sbRIO-9603 Montageanleitung

National Instruments

National Instruments MXI-Express Gen-3 x16 Bedienungsanleitung

National Instruments

National Instruments PXI-8820 Bedienungsanleitung

National Instruments

National Instruments RMC-8356 Bedienungsanleitung

National Instruments

National Instruments PXI-8150B Kurzanleitung

National Instruments

National Instruments IC-3121 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung