National Instruments CRIO-9075 Bedienungsanleitung

OPERATING INSTRUCTIONS AND SPECIFICATIONS

CompactRIO cRIO-9075/9076

Reconfigurable Embedded Chassis with Integrated

Intelligent Real-Time Controller for CompactRIO

Figure 1. cRIO-9075/9076 Front Panel

1LEDs

2 RJ-45 Ethernet Port

3 USB Port (cRIO-9076 Only)

4 Power Connector

5 Reset Button

6 RS-232 Serial Port

™

cRIO-9075/9076 Operating Instructions and Specifications 2 ni.com

This document describes how to connect the cRIO-9075/9076 to a network

and how to use the features of the cRIO-9075/9076. This document also

contains specifications for the cRIO-9075/9076.

Safety Guidelines

Operate the cRIO-9075/9076 only as described in these operating

instructions.

Safety Guidelines for Hazardous Locations

The cRIO-9075/9076 is suitable for use in Class I, Division 2, Groups A,

B, C, D, T4 hazardous locations; Class 1, Zone 2, AEx nC IIC T4 and

Ex nL IIC T4 hazardous locations; and nonhazardous locations only.

Follow these guidelines if you are installing the cRIO-9075/9076 in a

potentially explosive environment. Not following these guidelines may

result in serious injury or death.

Caution Do not disconnect the power supply wires and connectors from the controller

unless power has been switched off.

Caution Substitution of components may impair suitability for Class I, Division 2.

Caution For Zone 2 applications, install the CompactRIO system in an enclosure rated to

at least IP 54 as defined by IEC 60529 and EN 60529.

Special Conditions for Hazardous Locations Use

in Europe

Some chassis have been evaluated as Ex nA nL IIC T4 equipment under

DEMKO Certificate No. 07 ATEX 0626664X. Each such chassis is marked

II 3G and is suitable for use in Zone 2 hazardous locations, in ambient

temperatures of –20 °C ≤Ta ≤ 55 °C.

Special Conditions for Marine Applications

Some chassis are Lloyd’s Register (LR) Type Approved for marine

applications. To verify Lloyd’s Register certification, visit ni.com/

certification and search for the LR certificate, or look for the Lloyd’s

©National Instruments Corporation 3 cRIO-9075/9076 Operating Instructions and Specifications

What You Need to Install the cRIO-9075/9076

❑CompactRIO reconfigurable embedded chassis with integrated

intelligent real-time controller

❑C Series I/O modules

❑DIN rail mount kit (for DIN rail mounting only)

❑Panel mount kit (for panel mounting only)

❑Two M4 or number 8 flathead screws (for mounting the chassis

without one of the listed mounting kits)

❑A number 2 Phillips screwdriver

❑Power supply

❑Ethernet cable

Notes Visit ni.com/info and enter the Info Code rdsoftwareversion to determine

which software you need to use the cRIO-9075/9076.

Mounting the cRIO-9075/9076

You can mount the chassis horizontally on a flat, vertical, metallic surface

such as a panel or wall. The maximum allowable ambient temperature for

operation in this configuration is 55 °C. Figure 2 shows the chassis

mounted horizontally.

Figure 2. cRIO-9075/9076 Mounted Horizontally

You can also mount the chassis on a panel or wall in other orientations, on

a non-metallic surface, on a 35 mm DIN rail, on a rack, in an enclosure, or

on a desktop. Mounting the chassis in these or other configurations can

reduce the maximum allowable ambient temperature and can affect the

typical accuracy of modules in the chassis.

cRIO-9075/9076 Operating Instructions and Specifications 4 ni.com

Note For information about how different mounting configurations can cause temperature

derating, go to ni.com/info and enter the Info Code criomounting.

Note For information about typical accuracy specifications for modules, go to

ni.com/info and enter the Info Code criotypical.

Note Measure the ambient temperature at each side of the chassis, 63.5 mm (2.5 in.) from

the side and 25.4 mm (1 in.) forward from the rear of the chassis, as shown in Figure 3.

Caution Your installation must meet the following requirements for space and cabling

clearance:

• Allow 25.4 mm (1 in.) on the top and the bottom of the chassis for air circulation.

• Allow 50.8 mm (2 in.) in front of modules for cabling clearance for common

connectors, such as the 10-terminal, detachable screw terminal connector, as shown

in Figure 3.

Figure 3. cRIO-9075/9076, Bottom View with Dimensions

Note Go to ni.com/info and enter the Info Code rdcrioconn to find the minimum

cabling clearance for C Series modules with other connector types.

1 Measure ambient temperature here. 2 Chassis Grounding Screw

178.1 mm

(7.01 in.)

29.1 mm

(1.14 in.)

64.3mm

(2.53in.)

Cabling Clearance

50.8 mm (2.00 in.)

25.4 mm

(1 in.)

63.5 mm

(2.50 in.)

25.4 mm

(1 in.)

63.5 mm

(2.50 in.)

©National Instruments Corporation 5 cRIO-9075/9076 Operating Instructions and Specifications

Figure 4. cRIO-9075/9076, Front View with Dimensions

Figure 5. cRIO-9075/9076, Side View with Dimensions

Note For more information about the dimensions of the CompactRIO system, including

detailed dimensional drawings, go to ni.com/dimensions.

87.3mm

(3.44 in.)

47.2 mm

(1.86 in.) 30.6 mm

(1.2 in.)

41.1 mm

(1.62 in.)

47.0 mm

(1.85 in.)

4 mm

(0.16 in.)

Cooling Outline

25.4 mm (1 in.)

Cooling Outline

25.4 mm (1 in.)

2X M4X0.7

44 mm

(1.73in.)

74.0 mm

(2.91 in.)

44.1 mm

(1.74 in.)

29.1 mm

(1.15 in.)

cRIO-9075/9076 Operating Instructions and Specifications 6 ni.com

The following sections contain instructions for the mounting methods.

Before using any of these mounting methods, record the serial number from

the back of the chassis. You will be unable to read the serial number after

you have mounted the chassis.

Caution Make sure that no I/O modules are in the chassis before mounting it.

Mounting the Chassis on a Flat Surface

Using the NI 9904 Panel Mount Kit

Panel or wall mounting is the best method for applications that are subject

to high shock and vibration. You can use the NI 9904 panel mount kit to

mount the cRIO-9075/9076 on a flat surface. Complete the following steps.

1. Fasten the chassis to the panel mount kit using a number 2 Phillips

screwdriver and two M4 ×25 screws. National Instruments provides

these screws with the panel mount kit. You must use these screws

because they are the correct depth and thread for the panel. Tighten the

screws to a maximum torque of 1.3 N ⋅m (11.5 lb ⋅in.).

Figure 6. Installing the Panel Mounting Plate on the cRIO-9075/9076

NI cRIO-9076

©National Instruments Corporation 7 cRIO-9075/9076 Operating Instructions and Specifications

Figure 7. Dimensions of cRIO-9075/9076 with Panel Mounting Plate Installed

2. Fasten the NI 9904 panel to the wall using the screwdriver and screws

that are appropriate for the wall surface. The maximum screw size is

M4 or number 8.

Mounting the Chassis Directly on a Flat Surface

Using the Mounting Holes

Panel or wall mounting is the best method for applications that are subject

to high shock and vibration. If you do not have the NI 9904 panel mount kit

and do not require the portability that the NI 9904 affords, you can mount

the chassis directly on a flat surface using the mounting holes. Complete

the following steps.

1. Align the chassis on the surface.

2. Fasten the chassis to the surface using M4 or number 8 flathead screws,

as shown in Figure 8. National Instruments does not provide these

screws with the chassis.

[

]

31.7 mm

(1.25 in.)

63.5 mm

(2.5 in.)

88.1 mm

(3.47 in.)

7.2 mm

(0.29 in.)

27.3mm

(1.08 in.)

235.0 mm

(9.25 in.)

215.9 mm

(8.5 in.)

29.5 mm

(1.16 in.)

9.5 mm

(0.38 in.)

cRIO-9075/9076 Operating Instructions and Specifications 8 ni.com

Figure 8. Mounting the Chassis Directly on a Flat Surface

Caution Make sure that no I/O modules are in the chassis before removing it from the

surface.

Mounting the Chassis on a DIN Rail

Using the NI 9912 DIN Rail Mount Kit

You can order the NI 9912 DIN rail mount kit if you want to mount the

chassis on a DIN rail. You need one clip for mounting the chassis on a

standard 35 mm DIN rail. Complete the following steps to mount the

chassis on a DIN rail.

1. Fasten the DIN rail clip to the chassis using a number 2 Phillips

screwdriver and two M4 ×25 screws. National Instruments provides

these screws with the DIN rail mount kit. Tighten the screws to a

maximum torque of 1.3 N ⋅m (11.5 lb ⋅in.).

©National Instruments Corporation 9 cRIO-9075/9076 Operating Instructions and Specifications

Figure 9. Installing the DIN Rail Clip on the cRIO-9075/9076

2. Insert one edge of the DIN rail into the deeper opening of the DIN rail

clip, as shown in Figure 10.

Figure 10. One Edge of the DIN Rail Inserted in a Clip

3. Press down firmly on the chassis to compress the spring until the clip

locks in place on the DIN rail.

1 DIN Rail Clip 2 DIN Rail 3 DIN Rail Spring

cRIO-9075/9076 Operating Instructions and Specifications 10 ni.com

Mounting the Chassis on a Desktop

Using the NI 9901 Desktop Mounting Kit

You can use the NI 9901 desktop mounting kit to mount the chassis on a

desktop. You must install the adapter bracket using two M3 ×20 screws.

The adapter bracket and the screws are included in the kit. Refer to the

NI 9901 documentation for information about mounting the chassis on a

desktop.

Installing C Series I/O Modules in the Chassis

Figure 11 shows the mechanical dimensions of C Series I/O modules.

Figure 11. C Series I/O Module, Front and Side View with Dimensions

Complete the following steps to install a C Series I/O module in the chassis.

1. Make sure that no I/O-side power is connected to the I/O module. If the

system is in a nonhazardous location, the chassis power can be on

when you install I/O modules.

2. Align the I/O module with an I/O module slot in the chassis as shown

in Figure 12. The module slots are numbered 1 to 4, left to right.

88.1 mm

(3.47 in.)

70.7 mm

(2.78 in.)

22.9 mm

(0.90 in.)

Andere Handbücher für cRIO-9075

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Instruments E/A-System Handbücher

National Instruments

National Instruments DAQCard-6533 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-4463 Handbuch

National Instruments

National Instruments IMAQ SCB-100 Bedienungsanleitung

National Instruments

National Instruments USB-9237 Bedienungsanleitung

National Instruments

National Instruments NI 6581 Bedienungsanleitung

National Instruments

National Instruments SC Express PXIe-4309 Bedienungsanleitung

National Instruments

National Instruments PXI-7842 Bedienungsanleitung

National Instruments

National Instruments 9220 Bedienungsanleitung

National Instruments

National Instruments NI-9238 Bedienungsanleitung

National Instruments

National Instruments 8-Channel Solid-State Relay (SSR) Digital Output NI... Bedienungsanleitung

National Instruments

National Instruments NI USB-9234 Bedienungsanleitung

National Instruments

National Instruments FieldPoint FP-DO-400 Bedienungsanleitung

National Instruments

National Instruments 9211 Handbuch

National Instruments

National Instruments NI-9224 Bedienungsanleitung

National Instruments

National Instruments M Series Bedienungsanleitung

National Instruments

National Instruments 6711 Bedienungsanleitung

National Instruments

National Instruments NI 9225 Bedienungsanleitung

National Instruments

National Instruments AT E Series Bedienungsanleitung

National Instruments

National Instruments DAQPad-6508 Bedienungsanleitung

National Instruments

National Instruments NI 9381 Bedienungsanleitung

National Instruments

National Instruments 9225E Bedienungsanleitung

National Instruments

National Instruments PXIe-4339 Handbuch

National Instruments

National Instruments PXIe-7820 Bedienungsanleitung

National Instruments

National Instruments NI 9239 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

National Instruments cRIO-9075 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken