National Instruments IMAQ SCB-100 Bedienungsanleitung

INSTALLATION GUIDE AND SPECIFICATIONS

NI SCB-100

Shielded 100-Pin Connector Block for Plug-In DAQ Devices

This guide describes how to connect and use the NI SCB-100 with 100-pin data acquisition

(DAQ) devices.

The SCB-100 is a shielded desktop accessory with 100 screw terminals, a cold-junction

compensation temperature sensor for use with thermocouples, and a strain-relief bar for

securing signal wires or cables.

The SCB-100 connects to E Series MIO devices (NI 6025E, NI 6031E, NI 6033E, and NI

6071E), DIO devices (PCI-DIO-96, NI 6508, NI 6509, NI 6511, NI 6512, NI 6513, NI 6514,

NI 6515, NI 6527, and NI 6528), TIO Series devices (NI 6624), or other products with a 100-

pin 0.050 series shielded D-type I/O connector.

Note To use the SCB-100 with a DIO or TIO Series device, you must change the

default switch setting. Refer to the Using the SCB-100 with DIO/TIO Devices

section for more information.

The following illustration shows the SCB-100 components.

Figure 1. SCB-100 Connector Block

1. Quick Reference Label

2. Top Cover

3. 100-Pin Connector Screw

4. Grounding Screw

5. 100-Pin I/O Connector

6. Base

7. Strain-Relief Hardware

8. Strain-Relief Screws

9. SCB-100 Board Assembly

What You Need to Get Started

• SCB-100 100-pin shielded connector block and quick reference label

• 100-pin DAQ device and device documentation

• SH100100 cable (part number 182853-0x) for E Series/MIO devices or SH100-100-F

cable (part number 185095-0x) for DIO/TIO Series devices

• Phillips #1 and #2 screwdrivers

• 14-26 AWG wire

• Wire cutters

• Wire insulation strippers

• 1/8 in. flathead screwdriver

• Soldering iron and solder (optional)

• Long-nose pliers (optional)

• Resistors and capacitors specific to your application (optional)

Attaching the Quick Reference Label

A quick reference label is included in the SCB-100 100-pin shielded connector block kit to

show switch configurations and define screw terminal pinouts for E Series devices. Place the

label on the inside of the top cover.

2| ni.com | NI SCB-100 Installation Guide and Specifications

A PDF of the E Series quick reference label is available by going to ni.com/info and entering

the info code rdwpdf.

For DIO, TIO Series, or other 100-pin device signal information, refer to your device

documentation.

Getting Started with the SCB-100

Caution To avoid electrical shock, do not remove equipment covers or shields

unless you are qualified to do so. If signal wires are connected to the SCB-100,

hazardous voltages may exist even when the equipment is turned off. Before

removing the cover, disconnect the AC power or any live circuit from the connector

block.

The chassis ground terminals on your SCB-100 are for grounding high-impedance sources

such as a floating source (1 mA maximum). Do not use these terminals as safety earth

grounds.

Do not connect hazardous voltages (≥42 Vpk/60 VDC). National Instruments is not liable for

damage or injury resulting from such misuse.

The following figure shows the SCB-100 board parts locator diagram.

NI SCB-100 Installation Guide and Specifications | © National Instruments | 3

Figure 2. SCB-100 Board Parts Locator Diagram

1. Switches S4, S5, and S6

2. 100-Pin I/O Connector

3. Board Mount Screw Hole

4. Signal Accessory Power LED (DS1)

5. Switches S1, S2, and S3

6. Screw Terminals

7. Breadboard Area

8. Vias Shorted to Screw Termina

9. Cold-Junction Compensation Temperature Sensor

To get started with the SCB-100, complete the following steps.

1. Disconnect the 100-pin cable from the SCB-100, if connected.

2. Remove the grounding screws on either side of the top cover with a Phillips #1

screwdriver. Open the top cover.

3. Configure switches for the signal types you are using, as explained in the Using the

SCB-100 with DIO/TIO Devices section or the Using the SCB-100 with MIO Devices

section.

4| ni.com | NI SCB-100 Installation Guide and Specifications

4. Adjust the strain-relief hardware.

a. Loosen the strain-relief screws with a Phillips #2 screwdriver and slide the signal

wires through the front panel strain-relief opening.

b. If you are connecting multiple signals, remove the top strain-relief bar.

5. Add insulation or padding if necessary.

6. Connect the wires to the screw terminals by stripping 1/4 in. of insulation, inserting the

wires into the screw terminals, and tightening the screws.

7. Reinstall strain-relief (if removed) and tighten the strain-relief screws.

8. Close the top cover.

9. Reinsert the grounding screws to ensure proper shielding.

10. Connect the SCB-100 to the 100-pin connector.

Using the SCB-100 with DIO/TIO Devices

Caution Use the NI SH100-100-F cable with DIO devices, and the NI SH100-100

cable with MIO devices. Using the SH100-100 cable with a DIO device can damage

the device.

DIO devices, TIO Series devices, and DAQ devices without analog input functionality must

use the DIO/passthrough mode. Move the switches to the DIO/passthrough mode switch

setting as shown in the following table.

Table 1. DIO/TIO Series Device Switch Setting

Switch Setting Description

S6 S5 S4

DIO/passthrough mode—Move switches S1, S2, S3, S4, S5, and

S6 to the positions shown on the left. In this mode:

• All 100 signals from the DAQ device connect directly to

screw terminals

• The signal accessory power LED (DS1) does not light in this

configuration.

Refer to the following figure for a detailed diagram.

NI SCB-100 Installation Guide and Specifications | © National Instruments | 5

Figure 3. DIO/Passthrough Mode Switch Setting

Temperature

Sensor

DAQ Device SH100-100-F Cable SCB-100 Screw

Terminal

100

LED

S6 S5 S4

Refer to your device documentation for device signal information.

Using the SCB-100 with MIO Devices

You can take measurements with the SCB-100 and MIO DAQ devices, such as E Series, in a

number of ways. The SCB-100 has a temperature sensor for cold-junction compensation to

accommodate thermocouples. Switches S4, S5, and S6 configure the temperature sensor for

different analog input settings. The following table shows the different switch settings for

MIO DAQ devices.

6| ni.com | NI SCB-100 Installation Guide and Specifications

Switch Setting Description

S6 S5 S4

MIO with disabled temperature sensor mode (default

configuration)—Move switches S1, S2, S3, S4, S5, and S6 to the

positions shown on the left. In this mode:

• The temperature sensor is not used.

• AI 0 and AI 8 are available on screw terminals.

• The signal accessory power LED (DS1) lights when the

MIO device is powered on and connected to the SCB-100.

Refer to the following figure for a detailed diagram.

S6 S5 S4

MIO with single-ended temperature sensor mode—Move

switches S1, S2, S3, S4, S5, and S6 to the positions shown on the

left. In this mode:

• The temperature sensor can be read using AI 0 in referenced

single-ended (RSE) mode.

• AI 8 is available on a screw terminal.

• The signal accessory power LED (DS1) lights when the

MIO device is powered on and connected to the SCB-100.

Refer to the following figure for a detailed diagram.

S6 S5 S4

MIO with differential temperature sensor mode—Move switches

S1, S2, S3, S4, S5, and S6 to the positions shown on the left. In

this mode:

• The temperature sensor can be read using AI 0 and AI 8 in

differential mode.

• The signal accessory power LED (DS1) lights when the

MIO device is powered on and connected to the SCB-100.

Refer to the following figure for a detailed diagram.

S6 S5 S4

DIO/passthrough mode—You can use DIO/passthrough mode

with an MIO device.

Refer to the Using the SCB-100 with DIO/TIO Devices section for

configuration information and a detailed diagram.

NI SCB-100 Installation Guide and Specifications | © National Instruments | 7

Figure 4. MIO Device Modes Switch Settings

Temperature

Sensor

DAQ Device SH100-100 Cable SCB-100

LED

Screw

Terminal

100

+5 V

AI 0

AI 8

Other

Pins

Refer to your device documentation for device signal information.

Temperature Sensor Output and Accuracy

The SCB-100 temperature sensor outputs 10 mV/°C and has an accuracy of ±0.5 °C.

You also can determine the temperature using the following formulas:

TC= 100 × Vt

TK=TC+ 273.15

TF=9

5×TC+ 32

Where

Vt is the temperature sensor output voltage;

TK is the temperature in Kelvin;

8| ni.com | NI SCB-100 Installation Guide and Specifications

TF and TC are the temperature readings in degrees Fahrenheit and degrees Celsius,

respectively.

Note Use the average of a large number of samples to obtain the most accurate

reading. Noisy environments require averaging more samples for greater accuracy.

Connecting Nonreferenced or Floating Signal

Sources to Analog Inputs

A floating signal source is a signal source that is not connected in any way to the building

ground system but has an isolated ground-reference point. If an instrument or device has an

isolated output, that instrument or device falls into the floating signal source category. Some

examples of floating signal sources are outputs for the following: thermocouples,

transformers, battery-powered devices, optical isolators, and isolation amplifiers. The ground

reference of a floating source must be tied to the ground of the MIO DAQ device to establish a

local or onboard reference for the signal. If this reference is not established, erratic readings

from the board will occur.

Differential Inputs

To provide a return path for the instrumentation amplifier bias currents, floating sources must

have a 10 to 100 kΩ resistor connected to the AI GND signal line on one input if DC-coupled,

or both inputs if AC-coupled. For detailed information on connections to floating signal

sources and differential inputs, refer to your device documentation.

Single-Ended Inputs

When measuring floating signal sources, configure the MIO DAQ device to supply a ground

reference. Therefore, configure the MIO DAQ device for referenced single-ended (RSE) input.

In this configuration, the negative input of the MIO DAQ device instrumentation amplifier is

tied to the analog ground. For detailed information on connections to floating signal sources

and single-ended inputs, refer to your device documentation.

Connecting Ground-Referenced Signal Sources

to Analog Inputs

A grounded signal source is connected in some way to the building system ground; therefore,

the signal source is already connected to a common ground point with respect to the MIO

DAQ device (assuming the host computer is plugged into the same power system).

Nonisolated outputs of instruments and devices that plug into the building power system fall

into this category.

NI SCB-100 Installation Guide and Specifications | © National Instruments | 9

Differential Inputs

If the MIO DAQ device is configured for differential inputs, ground-referenced signal sources

connected to the SCB-100 board do not require special components added to the SCB-100

board. For detailed information about connections to ground-referenced signal sources and

differential inputs, refer to your device documentation.

Single-Ended Inputs

The maximum voltage level generated by thermocouples is typically a few millivolts.

Therefore, for best resolution, use an MIO DAQ device with a high gain.

Thermocouples can be measured in either differential or single-ended configurations. The

differential configuration has better noise immunity, but the single-ended configuration has

twice as many inputs. The MIO DAQ device must have a ground reference because

thermocouples are floating signal sources. Therefore, you must install bias resistors if the MIO

DAQ device is in differential mode. For single-ended configuration, use the referenced single-

ended input configuration.

Cold-junction compensation with the SCB-100 is accurate only if the temperature sensor

reading is close to the actual temperature of the screw terminals. Therefore, when reading

thermocouples, keep the SCB-100 away from drafts or other temperature gradients such as

those caused by heaters, radiators, fans, and warm equipment.

Using the SCB-100 for Thermocouple

Measurements

The maximum voltage level generated by thermocouples is typically a few millivolts.

Therefore, for best resolution, use an MIO DAQ device with a high gain.

Thermocouples can be measured in either differential or single-ended configurations. The

differential configuration has better noise immunity, but the single-ended configuration has

twice as many inputs. The MIO DAQ device must have a ground reference because

thermocouples are floating signal sources. Therefore, you must install bias resistors if the MIO

DAQ device is in differential mode. For single-ended configuration, use the referenced single-

ended input configuration.

Cold-junction compensation with the SCB-100 is accurate only if the temperature sensor

reading is close to the actual temperature of the screw terminals. Therefore, when reading

thermocouples, keep the SCB-100 away from drafts or other temperature gradients such as

those caused by heaters, radiators, fans, and warm equipment.

10 | ni.com | NI SCB-100 Installation Guide and Specifications

Andere Handbücher für IMAQ SCB-100

Inhaltsverzeichnis

Andere National Instruments E/A-System Handbücher

National Instruments

National Instruments R Series Bedienungsanleitung

National Instruments

National Instruments NI-9228 Handbuch

National Instruments

National Instruments SCB-68 Bedienungsanleitung

National Instruments

National Instruments NI 6115 Bedienungsanleitung

National Instruments

National Instruments NI 9469 Bedienungsanleitung

National Instruments

National Instruments NI PXI-7851 Bedienungsanleitung

National Instruments

National Instruments SCC-68 Bedienungsanleitung

National Instruments

National Instruments NI USB-6000 Bedienungsanleitung

National Instruments

National Instruments PXIe-7846R Bedienungsanleitung

National Instruments

National Instruments NI 9216 Bedienungsanleitung

National Instruments

National Instruments 9225 Bedienungsanleitung

National Instruments

National Instruments NI 9234E Bedienungsanleitung

National Instruments

National Instruments 776570-00 Bedienungsanleitung

National Instruments

National Instruments FieldPoint FP-DI-330 Bedienungsanleitung

National Instruments

National Instruments NI 6583R Bedienungsanleitung

National Instruments

National Instruments Isolated Analog Input Modules SCC-AI01 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-4300 Bedienungsanleitung

National Instruments

National Instruments PXIe-4339 Bedienungsanleitung

National Instruments

National Instruments 8-Channel Solid-State Relay (SSR) Digital Output NI... Bedienungsanleitung

National Instruments

National Instruments E Series Bedienungs- und Wartungshandbuch

National Instruments

National Instruments USB-9211A Bedienungsanleitung

National Instruments

National Instruments 9215E Bedienungsanleitung

National Instruments

National Instruments USB-9265 Bedienungsanleitung

National Instruments

National Instruments PXIe-7822R Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung