National Instruments NI REM-11100 Bedienungsanleitung

GETTING STARTED GUIDE

NI REM-11100

Voltage Input Module for Remote I/O

This document explains how to connect to the REM-11100.

Note The guidelines in this document are specific to the REM-11100. The other

components in the system might not meet the same safety ratings. Refer to the

documentation for each component in the system to determine the safety and EMC

ratings for the entire system.

Caution Do not operate the REM-11100 in a manner not specified in this

document. Product misuse can result in a hazard. You can compromise the safety

protection built into the product if the product is damaged in any way. If the product

is damaged, return it to NI for repair.

Isolation Withstand Voltages

Test section Test voltage

5 V communications power (logic), 24 V supply (I/O) 500 VAC, 50 Hz, 1 min.

5 V supply (logic) / analog inputs 500 VAC, 50 Hz, 1 min.

5 V supply (logic) / functional earth ground 500 VAC, 50 Hz, 1 min.

24 V supply (I/O) / analog inputs 500 VAC, 50 Hz, 1 min.

24 V supply (I/O) / functional earth ground 500 VAC, 50 Hz, 1 min.

Analog inputs / functional earth ground 500 VAC, 50 Hz, 1 min.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits provide reasonable protection against harmful interference when the product is

operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved by National

Instruments could void your authority to operate it under your local regulatory rules.

Preparing the Environment

Ensure that the environment in which you are using the REM-11100 meets the following

specifications.

Operating temperature -25 °C to 60 °C

Operating humidity 5% RH to 95% RH, noncondensing

Pollution Degree 2

Maximum altitude 3,000 m

2| ni.com | REM-11100 Getting Started Guide

Indoor use only.

Note Refer to the device datasheet on ni.com/manuals for complete specifications.

Verifying the Kit Contents

Verify that the following items are included in the REM-11100 kit.

Figure 1. REM-11100 Kit Contents

12 3 4

1. NI REM-11100

2. Bus connector

3. Supply voltage connector

4. Spring-terminal block (x2)

Unpacking the Kit

Caution To prevent electrostatic discharge (ESD) from damaging the device,

ground yourself using a grounding strap or by holding a grounded object, such as

your computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the device from the package and inspect the device for loose components or any

other sign of damage.

Caution Never touch the exposed pins of connectors.

Note Do not install a device if it appears damaged in any way.

3. Unpack any other items and documentation from the kit.

Store the device in the antistatic package when the device is not in use.

REM-11100 Getting Started Guide | © National Instruments | 3

Installing the REM-11100

Figure 2. Structure of the REM-11100

1. Bus connector

2. REM-11100

3. Module function label

4. Supply voltage connector

5. Spring-terminal block

6. LED indicators

Table 1. Module Function Labels

Label Color Module Function

Blue Digital input

Red Digital output

Green Analog input, thermocouple

Yellow Analog output

White Bus coupler, power module

Installing Bus Connectors

What to Use

• Bus connector

• DIN rail

What to Do

Complete the following steps to install bus connectors on the DIN rail.

4| ni.com | REM-11100 Getting Started Guide

1. Insert the bus connector for the REM-11100 into the DIN rail.

Caution Verify that you are using the correct bus connector for the module

width.

2. Slide the bus connector along the DIN rail until it connects to the preceding bus

connector.

Note A bus connector will not attach to a preceding bus connector with a

mounted module. Remove the preceding module before installing additional

bus connectors.

3. Repeat Steps 2 and 3 for additional bus connectors.

Installing the Module

What to Use

• REM-11100

• Mounted bus connector

What to Do

Complete the following steps to install the REM-11100 on the DIN rail.

REM-11100 Getting Started Guide | © National Instruments | 5

Note When using the Remote I/O Shield Set, install the shield rail supports before

mounting the module.

1. Align the REM-11100 over the appropriate bus connector.

Note Verify that the bus connector socket aligns with the socket on the

underside of the module.

2. Press the REM-11100 directly onto the bus connector and DIN rail until it clicks into

place.

Caution Tilting the module when mounting it on the DIN rail will damage the

contacts.

Installing Spring-Terminal Blocks

What to Use

• REM-11100

• Spring-terminal block

What to Do

Align the spring-terminal block over the REM-11100 and press until it clicks into place.

6| ni.com | REM-11100 Getting Started Guide

REM-11100 Pinout

AI0+ to AI3+

AI0– to AI3–

GND

24 VDC

GND

b1 UIS0 to UIS3

Table 2. REM-11100 Signal Descriptions

Signal Color Description

a1, a2 Red 24 VDC (UA) Supply for analog modules (internally jumpered)

b1, b2 Blue GND Reference potential of the supply voltage (internally

jumpered)

00 to 03 Orange AI0+ to AI3+ Positive voltage connection for channel 0 to 3

10 to 13 AI0- to AI3- Negative voltage connection for channel 0 to 3

20 to 23 UIS0 to UIS3 24 V sensor supply for channel 0 to 3

30 to 33 GND Reference potential of sensor supply

REM-11100 Getting Started Guide | © National Instruments | 7

Figure 3. REM-11100 LEDs

Table 3. LED Indicators

LED LED Color LED Pattern Indication

Green

Solid The REM-11100 is ready for operation.

Flashing Data is invalid or unavailable.

Green/Yellow Flashing The REM-11100 cannot communicate with the

connected devices.

Yellow

Solid The REM-11100 did not detect a valid cycle after power-

on.

Flashing The REM-11100 is not part of the configuration.

Red

Solid The REM-11100 has lost connection to the Bus Coupler.

Flashing The REM-11100 has lost connection to the preceding

adjacent module.

— Off The REM-11100 is in reset mode.

Green Solid Supply for analog modules UA present.

— Off No Supply for analog modules UA.

Red Solid Supply for analog modules UA is faulty.

— Off Supply for analog modules UA is OK.

Red Solid I/O or channel error has occurred.

— Off No error

8| ni.com | REM-11100 Getting Started Guide

Table 4. Error Status of E1 and E2 LEDs

Error E1 LED E2 LED

No error Off Off

Underrange Off On

Overrange Off On

Supply voltage faulty (supply for analog modules UA) On On

Parameter table invalid Off On

Device error Off On

Flash format error Off On

Note The reported error depends on the measuring range. For information about

input scaling, refer to the device datasheet on ni.com/manuals.

Connecting the REM-11100

Figure 4. REM-11100 Voltage Measurement Connection

24 VDC

AI+ (0:3)

AI– (0:3)

UIS (0:3)

GND

24 VDC

Sensor

GND

REM-11100

–

UIS and GND are optional, sensor-dependent connections.

Note For information about fuse ratings for the REM-11100, refer to the device

datasheet on ni.com/manuals.

Connection Guidelines

• Always connect analog signals using shielded, twisted pair cables. Unshielded cables

may lead to values outside the specified tolerance limits in environments subject to heavy

noise.

• Connect the cable shield to functional earth ground immediately after the cables enter the

control cabinet.

• Connect the cable shield to a shield bus if you are not using a closed control cabinet.

REM-11100 Getting Started Guide | © National Instruments | 9

• NI recommends using the NI Remote I/O Shield Set for optimal shield connection.

• Make sure that devices you connect to the REM-11100 are compatible with the module

specifications.

• Push the wire into the terminal when using a solid wire or a stranded wire with a ferrule.

• Open the terminal by pressing a screwdriver into the spring lever when using a stranded

wire without a ferrule.

Removing Components

Removing Spring Terminal Blocks

Complete the following steps to remove a spring-terminal block from the REM-11100.

1. Press the locking latch to release the spring-terminal block.

2. Tilt the block toward the center of the module.

3. Remove the connector from the module.

Removing the REM-11100

Remove all connections before removing the REM-11100, either by disconnecting the cables

or removing the spring-terminal block.

What to Use

• Flathead Screwdriver

What to Do

Complete the following steps to remove the REM-11100 from the DIN rail.

10 | ni.com | REM-11100 Getting Started Guide

Inhaltsverzeichnis

Andere National Instruments E/A-System Handbücher

National Instruments

National Instruments NI 6238 Bedienungsanleitung

National Instruments

National Instruments 8-Channel Solid-State Relay (SSR) Digital Output NI... Bedienungsanleitung

National Instruments

National Instruments NI USB-6000 Bedienungsanleitung

National Instruments

National Instruments NI-9207 Bedienungsanleitung

National Instruments

National Instruments NI 9236 Bedienungsanleitung

National Instruments

National Instruments NI 9247 Bedienungsanleitung

National Instruments

National Instruments sbRIO-9219 Bedienungsanleitung

National Instruments

National Instruments PXIe-7822R Bedienungsanleitung

National Instruments

National Instruments CB-2162 Bedienungsanleitung

National Instruments

National Instruments 9225E Bedienungsanleitung

National Instruments

National Instruments SCXI-1104 Bedienungsanleitung

National Instruments

National Instruments NI PXI-7831R Bedienungsanleitung

National Instruments

National Instruments NI REM-11115 Bedienungsanleitung

National Instruments

National Instruments AT-MIO-16 Bedienungsanleitung

National Instruments

National Instruments NI 9231 Bedienungsanleitung

National Instruments

National Instruments 9220 Bedienungsanleitung

National Instruments

National Instruments USB-443 Series Handbuch

National Instruments

National Instruments 6703 Gebrauchs- und Pflegehandbuch

National Instruments

National Instruments NI PXI-665 Series Handbuch

National Instruments

National Instruments 9754 Bedienungsanleitung

National Instruments

National Instruments USB-6221 OEM Bedienungsanleitung

National Instruments

National Instruments DAQ PCI-1200 Bedienungsanleitung

National Instruments

National Instruments TB-9212 Handbuch

National Instruments

National Instruments NI PXI-1042 Series Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung