National Instruments NI REM-11115 Bedienungsanleitung

GETTING STARTED GUIDE

NI REM-11115

Analog Output Module for Remote I/O

This document explains how to connect to the REM-11115.

Note The guidelines in this document are specific to the REM-11115. The other

components in the system might not meet the same safety ratings. Refer to the

documentation for each component in the system to determine the safety and EMC

ratings for the entire system.

Caution Do not operate the REM-11115 in a manner not specified in this

document. Product misuse can result in a hazard. You can compromise the safety

protection built into the product if the product is damaged in any way. If the product

is damaged, return it to NI for repair.

Isolation Withstand Voltages

Test section Test voltage

5 V communications power (logic), 24 V supply (I/O) 500 VAC, 50 Hz, 1 min.

5 V supply (logic) / analog inputs 500 VAC, 50 Hz, 1 min.

5 V supply (logic) / functional earth ground 500 VAC, 50 Hz, 1 min.

24 V supply (I/O) / analog inputs 500 VAC, 50 Hz, 1 min.

24 V supply (I/O) / functional earth ground 500 VAC, 50 Hz, 1 min.

Analog inputs / functional earth ground 500 VAC, 50 Hz, 1 min.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits provide reasonable protection against harmful interference when the product is

operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved by National

Instruments could void your authority to operate it under your local regulatory rules.

Preparing the Environment

Ensure that the environment in which you are using the REM-11115 meets the following

specifications.

Operating temperature -25 °C to 60 °C

Operating humidity 5% RH to 95% RH, noncondensing

Pollution Degree 2

Maximum altitude 3,000 m

2| ni.com | REM-11115 Getting Started Guide

Indoor use only.

Note Refer to the device datasheet on ni.com/manuals for complete specifications.

Verifying the Kit Contents

Verify that the following items are included in the REM-11115 kit.

Figure 1. REM-11115 Kit Contents

12 3 4

1. NI REM-11115

2. Bus connector

3. Supply voltage connector

4. Spring-terminal block (x2)

Unpacking the Kit

Caution To prevent electrostatic discharge (ESD) from damaging the device,

ground yourself using a grounding strap or by holding a grounded object, such as

your computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the device from the package and inspect the device for loose components or any

other sign of damage.

Caution Never touch the exposed pins of connectors.

Note Do not install a device if it appears damaged in any way.

3. Unpack any other items and documentation from the kit.

Store the device in the antistatic package when the device is not in use.

REM-11115 Getting Started Guide | © National Instruments | 3

Installing the REM-11115

Figure 2. Structure of the REM-11115

1. Bus connector

2. REM-11115

3. Module function label

4. Supply voltage connector

5. Spring-terminal block

6. LED indicators

Table 1. Module Function Labels

Label Color Module Function

Blue Digital input

Red Digital output

Green Analog input, thermocouple

Yellow Analog output

White Bus coupler, power module

Installing Bus Connectors

What to Use

• Bus connector

• DIN rail

What to Do

Complete the following steps to install bus connectors on the DIN rail.

4| ni.com | REM-11115 Getting Started Guide

1. Insert the bus connector for the REM-11115 into the DIN rail.

Caution Verify that you are using the correct bus connector for the module

width.

2. Slide the bus connector along the DIN rail until it connects to the preceding bus

connector.

Note A bus connector will not attach to a preceding bus connector with a

mounted module. Remove the preceding module before installing additional

bus connectors.

3. Repeat Steps 2 and 3 for additional bus connectors.

Installing the Module

What to Use

• REM-11115

• Mounted bus connector

What to Do

Complete the following steps to install the REM-11115 on the DIN rail.

REM-11115 Getting Started Guide | © National Instruments | 5

Note When using the Remote I/O Shield Set, install the shield rail supports before

mounting the module.

1. Align the REM-11115 over the appropriate bus connector.

Note Verify that the bus connector socket aligns with the socket on the

underside of the module.

2. Press the REM-11115 directly onto the bus connector and DIN rail until it clicks into

place.

Caution Tilting the module when mounting it on the DIN rail will damage the

contacts.

Installing Spring-Terminal Blocks

What to Use

• REM-11115

• Spring-terminal block

What to Do

Align the spring-terminal block over the REM-11115 and press until it clicks into place.

6| ni.com | REM-11115 Getting Started Guide

REM-11115 Pinout

AO0 to AO3

COM

24 VDC

GND

Table 2. REM-11115 Signal Descriptions

Signal Color Description

a1, a2 Red 24 VDC (UA) Analog module supply (internally jumpered)

b1, b2 Blue GND Reference potential of the supply voltage (internally

jumpered)

00 to 03 Orange AO0 to AO3 Voltage connection for channel 0 to 3

10 to 13 AO0 to AO3 Current connection for channel 0 to 3

20 to 23 COM Reference potential for all channels

30 to 33 COM Reference potential for all channels

REM-11115 Getting Started Guide | © National Instruments | 7

Figure 3. REM-11115 LEDs

Table 3. LED Indicators

LED LED Color LED Pattern Indication

Green

Solid The REM-11115 is ready for operation.

Flashing Data is invalid or unavailable.

Green/Yellow Flashing The REM-11115 cannot communicate with the

connected devices.

Yellow

Solid The REM-11115 did not detect a valid cycle after power-

on.

Flashing The REM-11115 is not part of the configuration.

Red

Solid The REM-11115 has lost connection to the Bus Coupler.

Flashing The REM-11115 has lost connection to the preceding

adjacent module.

— Off The REM-11115 is in reset mode.

Green Solid Supply to analog output module present.

— Off No supply to analog output modules.

Red Solid Supply to analog output module is faulty.

— Off Supply to analog output module is OK.

Red Solid I/O or channel error has occurred.

— Off No error

8| ni.com | REM-11115 Getting Started Guide

Table 4. Error Status of E1 and E2 LEDs

Error E1 LED E2 LED

No error Off Off

Short-circuit Off On

Open circuit Off On

Supply voltage faulty On On

Parameter table invalid Off On

Device error Off On

Flash format error Off On

Note The reported error depends on the measuring range. For information about

input scaling, refer to the device datasheet on ni.com/manuals.

Note An output value >1.7 % of the output range results in a short circuit or open

circuit error. An open circuit error occurs if the actuator is disconnected during

output.

Connecting the REM-11115

Figure 4. REM-11115 Voltage Output Connection

24 VDC

A0 (0:3) Voltage

A0 (0:3) Current

COM

REM-11115

–

Load

REM-11115 Getting Started Guide | © National Instruments | 9

Figure 5. REM-11115 Current Output Connection

24 VDC

A0 (0:3) Voltage

A0 (0:3) Current

COM

REM-11115

–

Load

Note For information about fuse ratings for the REM-11115, refer to the device

datasheet on ni.com/manuals.

Connection Guidelines

• Always connect analog signals using shielded, twisted pair cables. Unshielded cables

may lead to values outside the specified tolerance limits in environments subject to heavy

noise.

• Connect the cable shield to functional earth ground immediately after the cables enter the

control cabinet.

• Connect the cable shield to a shield bus if you are not using a closed control cabinet.

• NI recommends using the NI Remote I/O Shield Set for optimal shield connection.

• Make sure that devices you connect to the REM-11115 are compatible with the module

specifications.

• Push the wire into the terminal when using a solid wire or a stranded wire with a ferrule.

• Open the terminal by pressing a screwdriver into the spring lever when using a stranded

wire without a ferrule.

10 | ni.com | REM-11115 Getting Started Guide

Inhaltsverzeichnis

Andere National Instruments E/A-System Handbücher

National Instruments

National Instruments PXI-7830R Bedienungsanleitung

National Instruments

National Instruments PXIe-7858 Bedienungsanleitung

National Instruments

National Instruments PXIe-7865 Handbuch

National Instruments

National Instruments USB-9265 Bedienungsanleitung

National Instruments

National Instruments 9211 Handbuch

National Instruments

National Instruments 6527 Bedienungs- und Wartungshandbuch

National Instruments

National Instruments myRIO-1950 Bedienungsanleitung

National Instruments

National Instruments NI 9269 Handbuch

National Instruments

National Instruments NI USB-9229 Bedienungsanleitung

National Instruments

National Instruments 9361 Bedienungsanleitung

National Instruments

National Instruments PCIe-7856R Bedienungsanleitung

National Instruments

National Instruments NI-5761 Bedienungsanleitung

National Instruments

National Instruments FieldPoint FP-1300 Bedienungsanleitung

National Instruments

National Instruments DAQCard-6533 Bedienungsanleitung

National Instruments

National Instruments NI 9485 Bedienungsanleitung

National Instruments

National Instruments NI-6589 Bedienungsanleitung

National Instruments

National Instruments USB-6501 Bedienungsanleitung

National Instruments

National Instruments E Series Bedienungs- und Wartungshandbuch

National Instruments

National Instruments NI PXI-7851 Bedienungsanleitung

National Instruments

National Instruments SC-206 Series Bedienungsanleitung

National Instruments

National Instruments 9225E Bedienungsanleitung

National Instruments

National Instruments PCI-6238 Bedienungsanleitung

National Instruments

National Instruments 9220 Handbuch

National Instruments

National Instruments FOUNDATION Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung