National Instruments SCC-PWR01 Bedienungsanleitung

SCC-PWR01

USER GUIDE

SCC-AI Series Isolated Analog

Input Modules

The SCC-AI Series isolated analog input modules can extract a relatively

low-amplitude input signal from a high-common-mode voltage so the

E/M Series DAQ device can measure the input signal. They also can

amplify and filter the input signal, resulting in higher measurement

resolution and accuracy.

SCC-AI Series modules are available in a range of gains from 0.2 to 200.

They contain lowpass filters of either 10 kHz or 4 Hz bandwidth. Table 1

gives the gain and bandwidth for each module.

Table 1. SCC-AI Module Input/Output Range, Gain, and Bandwidth

Model Input Range Output Range Gain Bandwidth

SCC-AI01 ±42 Vpk/ VDC ±8.4 V 0.2 10 kHz

SCC-AI02 ±20 V ±10 V 0.5 10 kHz

SCC-AI03 ±10 V ±10 V 110 kHz

SCC-AI04 ±5 V ±10 V 210 kHz

SCC-AI05 ±1 V ±10 V 10 10 kHz

SCC-AI06 ±100 mV ±10 V 100 10 kHz

SCC-AI07 ±50 mV ±10 V 200 10 kHz

SCC-AI13 ±10 V ±10 V 14 Hz

SCC-AI14 ±5 V ±10 V 24 Hz

SCC-AI Series Isolated Analog Input Modules User Guide 2 ni.com

Conventions

The following conventions are used in this guide:

<> Angle brackets that contain numbers separated by an ellipsis represent

a range of values associated with a bit or signal name—for example,

AI <0..7>.

»The »symbol leads you through nested menu items and dialog box options

to a final action. The sequence File»Page Setup»Options directs you to

pull down the File menu, select the Page Setup item, and select Options

from the last dialog box.

This icon denotes a note, which alerts you to important information.

This icon denotes a caution, which advises you of precautions to take to

avoid injury, data loss, or a system crash. When this symbol is marked on

the product, refer to the Read Me First: Safety and Radio-Frequency

Interference document, shipped with the product, for precautions to take.

When symbol is marked on a product, it denotes a warning advising you to

take precautions to avoid electrical shock.

When symbol is marked on a product, it denotes a component that may be

hot. Touching this component may result in bodily injury.

bold Bold text denotes items that you must select in the software, such as menu

items and dialog box options. Bold text also denotes parameter names.

italic Italic text denotes variables, emphasis, a cross-reference, or an introduction

to a key concept. Italic text also denotes text that is a placeholder for a word

or value that you must supply.

monospace Text in this font denotes text or characters that you should enter from the

keyboard, sections of code, programming examples, and syntax examples.

This font is also used for the proper names of disk drives, paths, directories,

programs, subprograms, subroutines, device names, functions, operations,

variables, filenames, and extensions.

SC-2345 SC-2345 refers to both the SC-2345 connector block and the SC-2345

configurable connector.

SCC SCC refers to any SCC series signal conditioning module.

SCC-AI SCC-AI refers to any isolated analog input module in the SCC-AI Series

unless otherwise noted.

©National Instruments Corporation 3 SCC-AI Series Isolated Analog Input Modules User Guide

What You Need to Get Started

To set up and use the SCC-AI, you need the following items:

❑Hardware

– SCC-68

– SC-2345/2350 with one of the following:

• SCC-PWR01

• SCC-PWR02 and the PS01 power supply

• SCC-PWR03 (requires a 7 to 42 VDC power supply,

not included)

– One or more SCC-AI

– 68-pin E/M Series DAQ device

– 68-pin cable

– Quick Reference Label

❑Software

– The latest version of NI-DAQmx

❑Documentation

– SCC-AI Series Isolated Analog Input Modules User Guide

–SC-2345/2350 User Manual

– SCC-68 User Guide

–SCC Quick Start Guide

–Read Me First: Safety and Radio-Frequency Interference

– Documentation for your hardware

– Documentation for your software

❑Tools

– 1/8 in. flathead screwdriver

– Numbers 1 and 2 Phillips screwdrivers

– Wire insulation stripper

Note Software scaling of measurements is not supported on the Macintosh operating

system. Refer to the SCC-AI Module Pin Assignments section.

SCC-AI Series Isolated Analog Input Modules User Guide 4 ni.com

You can download NI documents from ni.com/manuals. To download

the latest version of NI-DAQmx, click Download Software at ni.com.

Device Specific Information

Note For general SCC module installation and signal connection information, and

information about the SC-2345/2350 or SCC-68, refer to the SCC Quick Start Guide,

available for download at ni.com/manuals.

Installing the Module

Caution Refer to the Read Me First: Safety and Radio-Frequency Interference document

before removing equipment covers or connecting/disconnecting any signal wires.

You can plug the SCC-AI into any analog input socket on the

SC-2345/2350 or SCC-68. The socket you choose determines which

E/M Series DAQ device channels receive the SCC-AI signals.

For single-stage input conditioning, plug the SCC-AI into any slot of the

SC-68, or any socket of the SC-2345/2350 J(X+1), where Xis 0 to 7.

Connect the input signals to the module as described in the Connecting the

Input Signals section.

If you use the SCC-AI in a dual-stage configuration in an SC-2345, the

SCC-AI must be the first-stage module. Plug it into any socket J(X+9) and

plug the second-stage SCC into socket J(X+1), where Xis 0 to 7. Connect

the input signals to the SCC-AI as described in the Connecting the Input

Signals section. The SC-2345 connects the output signals of the first-stage

SCC to the inputs of the second-stage SCC. An example of dual-stage

conditioning is an SCC-AI02 followed by an SCC-FV01 frequency input

module.

Sockets J9 to J16 of the SC-2345 are also available for digital input/output

(DIO) conditioning or control. Refer to the SC-2345/2350 User Manual

for more information about configuring, connecting, and installing SCC

modules.

©National Instruments Corporation 5 SCC-AI Series Isolated Analog Input Modules User Guide

Connecting the Input Signals

Note The signal names have changed. Refer to ni.com/info and enter rdtntg to

confirm the signal names.

Each screw terminal on the SCC-AI is labeled by pin number <1..4>. Pins 1

and 2 form a channel routed to E/M Series DAQ device channel X+8, and

pins 3 and 4 form a channel routed to the E/M Series DAQ device channel

X, where Xis 0 to 7 depending on the socket where you plug in the module.

The SCC-AI provides channel-to-ground and module-to-module isolation

only. It does not provide isolation between the two channels of the SCC-AI.

Because both channels must have the same reference voltage, pins 1 and 3

are connected together internally.

Figure 1 shows the SCC-AI signal connections.

Figure 1. SCC-AI Signal Connections

The inputs are designed in a floating (nonreferenced) single-ended

configuration. If the measured signals are floating, connect the negative

input pins, 1 and 3, to AI SENSE on the SC-2345/2350 terminal block or

AI GND on the SC-68, through a 10 kΩto 100 kΩresistor. Figure 2 shows

a floating signal connection on one channel of the SCC-AI.

Lowpass

Filter

–

Lowpass

Filter

E/M Series DAQ Device

Signal

Source

AI (X )

SCC-AI

AI SENSE

AI GND

AI (X+8)

SCC-AI Series Isolated Analog Input Modules User Guide 6 ni.com

Figure 2. Nonreferenced Signal Connection for the SCC-AI (One Channel)

If a high common-mode voltage is present, connect the negative input pins,

1 and 3, to the signal reference. Figure 3 shows a ground-referenced signal

connection on one channel of the SCC-AI.

Figure 3. Ground-Referenced Signal Connection for the SCC-AI

with High Common-Mode Voltage (One Channel)

For information about how to configure the SCC-AI module using

NI-DAQmx, refer to the SCC Quick Start Guide.

Lowpass

Filter

–

Lowpass

Filter

E/M Series DAQ Device

Signal

Source AI (X )

SCC-AI

AI SENSE

AI GND

AI (X+8)

AI SENSE on

SC-2345/2350

terminal block

AI GND on

SCC-68

10 to 100 kΩ

Lowpass

Filter

–

Lowpass

Filter

E/M Series DAQ Device

Signal

Source AI (X )

SCC-AI

AI SENSE

AI GND

AI (X+8)

High

CMV

–

©National Instruments Corporation 7 SCC-AI Series Isolated Analog Input Modules User Guide

Using the SCC-AI when Scaling Voltage Measurements

If you configured the SCC-AI using Measurement & Automation Explorer

(MAX) and you are using NI-DAQmx, the voltage reading you get from the

E/M Series DAQ device accounts for the voltage scaling effect of the

SCC-AI. Otherwise, because the voltage measurement from the E/M Series

DAQ device is scaled by the gain given in Table 1, you must divide the

voltage reading returned by the E/M Series DAQ device by this gain to get

the correct input voltage.

Calibrating Gain and Offset Errors

The SCC-AI is calibrated at the factory before shipment. If you want to

adjust the gain of the SCC-AI in your system using your E/M Series DAQ

device, you need a voltage source that is several times more accurate than

the SCC itself and capable of providing the DC voltage shown in Table 2.

Gain Adjustment

To adjust the gain of the SCC-AI, complete the following steps:

1. Select the desired SCC-AI channel on the E/M Series DAQ device.

2. Set the gain on the E/M Series DAQ device so that its input range is

±10 V.

3. Connect the voltage source to the screw terminals of the desired

channel on the SCC-AI.

4. Apply the voltage given in Table 2 that corresponds to the SCC-AI

module. For example, if you have an SCC-AI03, you must apply

8 VDC.

Table 2. SCC-AI Input Voltage Requirements

Module Input Range

SCC-AI01 40 V

SCC-AI02 16 V

SCC-AI03 8 V

SCC-AI04 4 V

SCC-AI05 800 mV

SCC-AI06 80 mV

SCC-AI07 40 mV

SCC-AI13 8 V

SCC-AI14 4 V

SCC-AI Series Isolated Analog Input Modules User Guide 8 ni.com

5. Using your software, have the E/M Series DAQ device read the desired

channel on the SCC-AI and record the value.

6. Input 0 VDC to the SCC-AI.

7. Use the E/M Series DAQ device to read that channel and record the

value.

8. Subtract the values read ( first reading – second reading).

9. Adjust the trimpot labeled Gain located on the top of the SCC-AI. If

the value you obtained in step 8 is less than the input voltage, turn the

trimpot clockwise to increase the gain. If it is greater than the input

voltage, turn the trimpot counterclockwise to decrease the gain.

10. Repeat steps 4 through 9 until the difference you get in step 8 equals

the Input Voltage Required value shown in Table 2; in this example the

value is 8 V using an SCC-AI03.

For example, assume that you have an SCC-AI03 module. You first connect

8 VDC to the input of CH (X). The E/M Series DAQ device reads 8.05 V

as the SCC output. You then connect 0 VDC to the input of CH (X) and the

E/M Series DAQ device reads –0.01 V as the SCC output. You subtract

these readings, 8.05 – (–0.01) =8.06, getting a difference of 8.06 V.

Because this difference is not equal to 8 V, you must adjust the gain trimpot

and repeat the procedure until the difference in outputs equals 8 V.

Note In this example there can be an offset voltage such that the final readings are 8.01 V

and 0.01 V for a difference of 8 V. The gain trimpot adjusted in step 9 of the previous

procedure adjusts only for gain errors and does not compensate for this offset voltage.

Offset Voltage Adjustment

Complete the following steps to adjust the offset voltage of the SCC-AI:

1. Select the desired SCC-AI channel on the E/M Series DAQ device.

2. Set the gain on the E/M Series DAQ device so that the input range

is ±10 V.

3. Connect the screw terminals of your desired channel on the SCC-AI

together.

4. Using your software, have the E/M Series DAQ device read the

channel.

5. If the value read is not equal to 0.00 V, adjust the appropriate trimpot

located on the top of the SCC-AI, labeled Offset. Turn the trimpot

clockwise to increase the offset.

6. Repeat steps 4 and 5 until the voltage read in step 4 equals 0.00 V.

©National Instruments Corporation 9 SCC-AI Series Isolated Analog Input Modules User Guide

Specifications

These ratings are typical at 25 °C unless otherwise stated.

Input Characteristics

Number of input channels ...................... 2 NRSE

Isolation.................................................. Bank isolation

(isolation per module1)

Input/output signal range, gain,

and bandwidth ........................................ Refer to Table 1

Input impedance

SCC-AI01, SCC-AI02 .................... 1 MΩ

All others......................................... 100 MΩ

Gain error ............................................... 4.5% max (trimmable to zero)

Gain stability .......................................... 150 PPM/°C

Offset error............................................. 40 mV max (RTI2)

Offset stability........................................ 225 µV/°C

Nonlinearity ........................................... 0.0128% typ

0.0260% max

Common-mode rejection ratio ............... 100 dB typical at 60 Hz

Output slew rate,

dependent on BW (filtering) .................. 0.8 V/µs max

Filter Characteristics

Number of poles..................................... 3

Rolloff .................................................... 60 dB/decade

Cutoff frequency (–3 dB)

AI0X................................................ 10 kHz

AI1X................................................ 4 Hz

1 The SCC-AI does not provide isolation between the two channels of the module. For more information, refer

to the Connecting the Input Signals section.

2 This specification is calculated relative to the input range of the module.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Instruments E/A-System Handbücher

National Instruments

National Instruments NI-9244 Bedienungsanleitung

National Instruments

National Instruments SCXI-1120/D Bedienungsanleitung

National Instruments

National Instruments NI-9207 Bedienungsanleitung

National Instruments

National Instruments Isolated Analog Output Module SCC-AO10 Bedienungsanleitung

National Instruments

National Instruments PCIe-6374 Betriebsanleitung

National Instruments

National Instruments NI 9375 Bedienungsanleitung

National Instruments

National Instruments NI 9231 Bedienungsanleitung

National Instruments

National Instruments FieldPoint FP-AI-112 Bedienungsanleitung

National Instruments

National Instruments NI PXI-7831R Bedienungsanleitung

National Instruments

National Instruments cRIO-9075 Bedienungsanleitung

National Instruments

National Instruments NI USB-9229 Bedienungsanleitung

National Instruments

National Instruments PCIe-7822R Bedienungsanleitung

National Instruments

National Instruments SCXI-1104 Bedienungsanleitung

National Instruments

National Instruments SC-206 Series Bedienungsanleitung

National Instruments

National Instruments NI PXIe-4300 Bedienungsanleitung

National Instruments

National Instruments NI USB-9219 Bedienungsanleitung

National Instruments

National Instruments 6527 Bedienungs- und Wartungshandbuch

National Instruments

National Instruments BNC-2090A Bedienungsanleitung

National Instruments

National Instruments PXIe-7822 Bedienungsanleitung

National Instruments

National Instruments PXIe-5764 Betriebsanleitung

National Instruments

National Instruments 9215E Bedienungsanleitung

National Instruments

National Instruments FIELDPOINT FP-DO-403 Bedienungsanleitung

National Instruments

National Instruments 24-Bit Half/Full-Bridge Analog Input Module NI... Bedienungsanleitung

National Instruments

National Instruments USB-6525 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung