National Instruments NI PXIe-5624R Bedienungsanleitung

GETTING STARTED GUIDE

NI PXIe-5624R

2 GS/s, 12-Bit IF Digitizer

Note Before you begin, install and configure your chassis and controller.

This document explains how to install, configure, and test the NI PXIe-5624R (NI 5624R).

The NI 5624R is an IF digitizer with a user-programmable FPGA. The NI 5624R ships with

NI LabVIEW Instrument Design Libraries for IF Digitizers, which you can use to program the

device.

Programming the NI 5624R requires NI LabVIEW. Customizing the FPGA requires the

NI LabVIEW FPGA Module.

To access NI 5624R documentation, navigate to Start»All Programs»National Instruments»

IF Digitizers»IF Digitizers Documentation

Note The NI 5624R can be used on its own or as a component of certain NI vector

signal analyzers. Refer to the documentation for your vector signal analyzer for

information about using the NI 5624R in an NI vector signal analyzer.

Contents

Electromagnetic Compatibility Guidelines...............................................................................2

Verifying the System Requirements......................................................................................... 2

Unpacking the Kit.....................................................................................................................2

NI 5624R Kit Contents..................................................................................................... 3

Preparing the Environment....................................................................................................... 4

Programming the NI 5624R......................................................................................................4

Installing the Software.............................................................................................................. 4

Installing the NI 5624R.............................................................................................................5

NI 5624R Front Panel....................................................................................................... 8

Configuring the NI 5624R in MAX........................................................................................10

Self-Calibration.......................................................................................................................11

Making a Measurement with a Sample Project...................................................................... 11

Troubleshooting...................................................................................................................... 12

What Should I Do if the NI 5624R Doesn't Appear in MAX?....................................... 12

What Should I Do if the Module Fails the Self-Test or Self-Calibration?......................12

Where to Go Next................................................................................................................... 13

Worldwide Support and Services............................................................................................13

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits are designed to provide reasonable protection against harmful interference when the

product is operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any modifications to the product not expressly approved by National Instruments

could void your authority to operate it under your local regulatory rules.

Caution To ensure the specified EMC performance, operate this product only with

shielded cables and accessories.

Caution To ensure the specified EMC performance, the length of all I/O cables

must be no longer than 3 m (10 ft).

Verifying the System Requirements

To use the NI 5624R, your system must meet certain requirements.

For information about minimum system requirements, recommended system requirements,

and supported ADEs, refer to the readme for the NI LabVIEW Instrument Design Libraries for

IF Digitizers. When using the NI 5624R as a component of an NI vector signal analyzer, refer

to the NI-RFSA Readme. Readmes are available on the driver software DVD and online at

ni.com/updates.

Unpacking the Kit

Caution To prevent electrostatic discharge (ESD) from damaging the device,

ground yourself using a grounding strap or by holding a grounded object, such as

your computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the device from the package and inspect the device for loose components or any

other sign of damage.

Caution Never touch the exposed pins of connectors.

Notify NI if the device appears damaged in any way. Do not install a damaged device.

3. Unpack any other items and documentation from the kit.

Store the device in the antistatic package when the device is not in use.

2| ni.com | NI PXIe-5624R Getting Started Guide

NI 5624R Kit Contents

Figure 1. NI 5624R Kit Contents

1 2

3 4 5

1. NI PXIe-5624R IF Digitizer Module

2. Driver Software DVD

3. Read Me First: Safety and Electromagnetic

Compatibility

4. Maintain Forced-Air Cooling Note to Users

5. NI 5624R Getting Started Guide (This Document)

Other Equipment

There are several required items not included in your device kit that you need to operate the

NI 5624R. Your application may require additional items not included in your kit to install or

operate your device.

Required Items

• A PXI Express chassis and chassis documentation. The NI PXIe-1085 chassis is one

available option for your PXI Express device. For more information about compatible

chassis options, visit ni.com/info and enter the Info Code pxiechassis.

• A PXI Express embedded controller or PC with MXI controller system that meets the

system requirements specified in this guide and chassis documentation.

Optional Items

• PXI Chassis Slot Blocker kit (NI part number 199198-01)

• SMA (m)-to-SMA (m) cables

• NI SHH19-H19-AUX DIGITAL I/O cable (NI part number 152629-01 or 152629-02)

• NI SCB-19 DIGITAL I/O accessory for connecting to external signals (NI part number

782444-01)

NI PXIe-5624R Getting Started Guide | © National Instruments | 3

Preparing the Environment

Ensure that the environment you are using the NI 5624R in meets the following specifications.

............................................................................Operating ambient temperature

(IEC-60068-2-1, IEC-60068-2-2)

0 °C to 55 °C

............................................................................Operating relative humidity

(IEC-60068-2-56)

10% to 90%, noncondensing

............................................................................Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient

temperature)

............................................................................Pollution Degree 2

Indoor use only.

Caution Clean the hardware with a soft, nonmetallic brush. Make sure that the

hardware is completely dry and free from contaminants before returning it to

service.

Note Refer to the NI PXIe-5624R Specifications at ni.com/manuals for complete

specifications.

Programming the NI 5624R

You can use the NI LabVIEW Instrument Design Libraries for IF Digitizers and the LabVIEW

FPGA Module to customize the behavior of your NI 5624R.

You can use the instrument design libraries to control or customize your NI 5624R device to

suit the needs of your application. This software offers many LabVIEW libraries to assist you

in controlling your device.

Use the NI LabVIEW Instrument Design Libraries for IF Digitizers with the LabVIEW FPGA

Module to customize the behavior of the device FPGA to create application-specific

instrument designs. The NI LabVIEW Instrument Design Libraries for IF Digitizers

installation includes sample projects. You can use sample projects as a starting point for

customizing the device FPGA or to operate the device as a standard IF digitizer.

Installing the Software

Close all programs before installing the software. NI recommends installing your software

before installing the NI 5624R hardware.

Install your software in the following order:

1. Install the latest service packs for your operating system.

2. Install NI LabVIEW.

4| ni.com | NI PXIe-5624R Getting Started Guide

Refer to the LabVIEW Installation Guide for installation instructions for LabVIEW and

system requirements for LabVIEW software. Refer to the LabVIEW Upgrade Notes for

additional information about upgrading to the most recent version of LabVIEW for

Windows.

3. (Recommended) Install NI LabVIEW FPGA Module.

Refer to the LabVIEW FPGA Module Release and Upgrade Notes for installation

instructions and information about getting started with the LabVIEW FPGA Module.

Note Installation of the LabVIEW FPGA Module is required to customize the

device FPGA using the instrument design libraries.

4. (Recommended) Install the latest service pack for LabVIEW and any LabVIEW modules

you are using.

5. Insert the driver software DVD into the DVD drive.

The driver software installer should open automatically. If the installation window does

not appear, navigate to the DVD drive, double-click the drive, and double-click

autorun.exe.

Note You can also download the software from ni.com/downloads.

6. Follow the instructions in the installation prompts to install the default installation.

Windows users may see access and security messages during installation. Accept the

prompts to complete the installation.

Note The default installation installs NI LabVIEW Instrument Design

Libraries for IF Digitizers, documentation, and device specifications.

Note For troubleshooting information, contact NI technical support or visit

ni.com/support.

7. When the installer completes, restart your system.

Installing the NI 5624R

Caution To prevent damage to the device caused by ESD or contamination, handle

the device using the edges or the metal bracket.

NI recommends installing the software before installing the hardware.

Before you install the hardware, refer to the guidelines in the Maintain Forced-Air Cooling

Note to Users included with the module to ensure that the device can cool itself effectively.

This document is also available at ni.com/manuals.

1. Ensure the AC power source is connected to the chassis before installing the NI 5624R.

The AC power cord grounds the chassis and protects it from electrical damage while you

install the NI 5624R.

2. Power off the chassis.

NI PXIe-5624R Getting Started Guide | © National Instruments | 5

3. Inspect the slot pins on the chassis backplane for any bends or damage prior to

installation. Do not install the module if the backplane is damaged.

4. If the chassis has multiple fan speed settings, ensure the fans are set to the highest setting.

Note Inadequate air circulation could cause the temperature inside the chassis

to rise above the optimal operating temperature for the device, potentially

causing thermal shutdown, shorter lifespans, or improper performance.

5. Position the chassis so that inlet and outlet vents are not obstructed.

For more information about optimal chassis positioning, refer to the chassis

documentation.

6. Remove the black plastic connectors from all the captive screws on the module front

panel.

7. Identify a supported slot in the chassis. The following figure shows the symbols that

indicate the slot types.

Figure 2. Chassis Compatibility Symbols

NI PXIe-1062Q

12 3 45

1. PXI Express System Controller Slot

2. PXI Peripheral Slot

3. PXI Express Hybrid Peripheral Slot

4. PXI Express System Timing Slot

5. PXI Express Peripheral Slot

The NI 5624R module can be placed in PXI Express peripheral slots or PXI Express

Hybrid peripheral slots.

8. Touch any metal part of the chassis to discharge static electricity.

9. Ensure that the ejector handle is in the unlatched (downward) position.

10. Place the module edges into the module guides at the top and bottom of the chassis. Slide

the device into the slot until it is fully inserted.

6| ni.com | NI PXIe-5624R Getting Started Guide

Figure 3. Module Installation

NI PXIe-1075

1. Chassis

2. Hardware Module

3. Ejector Handle in Down (Unlatched Position)

11. Latch the module in place by pulling up on the ejector handle.

12. Secure the device front panel to the chassis using the front-panel mounting screws.

Note Tightening the top and bottom mounting screws increases mechanical

stability and also electrically connects the front panel to the chassis, which can

improve the signal quality and electromagnetic performance.

13. Cover all empty slots using filler panels or slot blockers to maximize cooling air flow.

14. Power on the chassis.

NI PXIe-5624R Getting Started Guide | © National Instruments | 7

NI 5624R Front Panel

The NI 5624R front panel contains five connectors and two LEDs.

Figure 4. NI 5624R IF Digitizer Module Front Panel

ACCESS

ACTIVE

8| ni.com | NI PXIe-5624R Getting Started Guide

Table 1. Device Front Panel Icon Definitions

Refer to the user documentation for required maintenance measures to ensure user

safety and/or preserve the specified EMC performance.

The signal pins of this product's input/output ports can be damaged if subjected to

Electrostatic Discharge (ESD). To prevent damage, turn off power to the product

before connecting cables and employ industry-standard ESD prevention measures

during installation, maintenance, and operation.

Table 2. NI 5624R IF Digitizer Front Panel Connectors

Label Connector Type Function

IF IN SMA connector Analog input terminal for intermediate frequency (IF)

signals.

PFI 0 SMA connector Programmable function digital I/O (DIO) connector for

triggers or events.

CLK IN SMA connector Input for an external ADC Clock (Sample Clock) or

Reference Clock to the digitizer.

CLK OUT SMA connector Output for an ADC Clock (Sample Clock) or PLL

Reference Clock from the digitizer.

DIGITAL I/O HDMI™ connector DIO terminal that contains 12 general-purpose DIO

signals. DIO lines are direction configurable as input or

output.

Caution The DIGITAL I/O connector accepts a standard, third-party HDMI cable,

but the DIGITAL I/O port is not an HDMI interface. Do not connect the DIGITAL

I/O port on the NI 5624R to the HDMI port of another device. NI is not liable for

any damage resulting from such signal connections.

The following table provides information about the module front panel LEDs and the device

states they indicate.

NI PXIe-5624R Getting Started Guide | © National Instruments | 9

Table 3. The NI 5624R IF Digitizer Front Panel LEDs

LED Indication

ACCESS Indicates the basic hardware status of the NI 5624R module.

• OFF—The module is not yet functional, or the module has detected a

problem with a PXI Express power rail.

• AMBER—The module is being accessed. Accessed means that the device

setup registers are being written to in order to control the device.

• GREEN—The module is ready to be programmed.

ACTIVE Indicates the NI 5624R module state.

• OFF—User has not turned on LED.

• AMBER—User defined.

• GREEN—User defined.

• RED—The module has detected a PLL unlock or an error state, such as a

clock fault, a power shutdown condition, or a thermal shutdown condition.

The behavior of this LED can also be user-defined.

Configuring the NI 5624R in MAX

Use Measurement & Automation Explorer (MAX) to configure your National Instruments

hardware. MAX informs other programs about which devices reside in the system and how

they are configured. MAX is automatically installed with NI LabVIEW Instrument Design

Libraries for IF Digitizers.

1. Launch MAX.

2. In the configuration tree, double-click Devices and Interfaces to see the list of installed

devices.

Installed devices appear under the name of their associated chassis.

3. Expand your Chassis tree item.

MAX lists all devices installed in the chassis. Your default device names may vary.

Note If you do not see your device listed, press <F5> to refresh the list of

installed devices. If the device is still not listed, power off the system, ensure

the device is correctly installed, and restart.

4. Record the device identifier MAX assigns to the hardware. Use this identifier when

programming the NI 5624R.

5. Self-test the device by selecting the device in the configuration tree and clicking Self-

Test in the MAX toolbar.

The MAX self-test performs a basic verification of hardware resources.

10 | ni.com | NI PXIe-5624R Getting Started Guide

Inhaltsverzeichnis

Andere National Instruments Messgerät Handbücher

National Instruments

National Instruments PXIe-4136 Bedienungsanleitung

National Instruments

National Instruments SA1000X Bedienungsanleitung

National Instruments

National Instruments NI PXI-6541 Bedienungsanleitung

National Instruments

National Instruments PXIe-5668 Bedienungsanleitung

National Instruments

National Instruments PXI-5660 Bedienungsanleitung

National Instruments

National Instruments FD-11605 Bedienungsanleitung

National Instruments

National Instruments PXIe-5665 Bedienungsanleitung

National Instruments

National Instruments 779640-01 Bedienungsanleitung

National Instruments

National Instruments PXIe-4162 Bedienungsanleitung

National Instruments

National Instruments NI 5911 Bedienungsanleitung

National Instruments

National Instruments NI 9421 Bedienungsanleitung

National Instruments

National Instruments PXIe-5668R Bedienungsanleitung

National Instruments

National Instruments NI PXIe-4143 Betriebsanleitung

National Instruments

National Instruments NI PXIe-4139 Handbuch

National Instruments

National Instruments USB-TC01 Bedienungsanleitung

National Instruments

National Instruments PXI-5142 Bedienungsanleitung

National Instruments

National Instruments 4551 Bedienungsanleitung

National Instruments

National Instruments 9235 Bedienungsanleitung

National Instruments

National Instruments NI 5105 Bedienungsanleitung

National Instruments

National Instruments RM-26999 Handbuch

National Instruments

National Instruments NI 5734 Bedienungsanleitung

National Instruments

National Instruments NI 435 Series Bedienungsanleitung

National Instruments

National Instruments NI 9213 Bedienungsanleitung

National Instruments

National Instruments PXI-5663 Handbuch

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung