National Instruments BNC-2120 Bedienungsanleitung

INSTALLATION GUIDE

BNC-2120

Connector Accessory for E/M/S Series Devices

This installation guide describes how to install, configure, and use your BNC-2120 accessory with

68-pin or 100-pin E/M/S Series multifunction data acquisition (DAQ) devices. This document also

contains accessory specifications.

The BNC-2120 has the following features:

• Eight BNC connectors for analog input (AI) connection

• Onboard temperature reference

• Thermocouple connector

• Resistor measurement screw terminals

• Two BNC connectors for analog output (AO) connection

• Screw terminals for digital I/O (DIO) connection with state indicators

• Screw terminals for timing I/O (TIO) connection

• Two user-defined BNC connectors

• A function generator with the following outputs:

– Frequency-adjustable, TTL-compatible square wave

– Frequency- and amplitude-adjustable sine wave or triangle wave

• Quadrature encoder

• A 68-pin I/O connector that connects to multifunction DAQ devices

• Can be used on a desktop or mounted on a DIN rail

Contents

Conventions ......................................................................................................................................... 2

What You Need to Get Started ............................................................................................................ 2

Installing the BNC-2120...................................................................................................................... 2

Connecting Analog Input Signals ........................................................................................................ 5

Connecting Differential Analog Input Signals ............................................................................ 5

Measuring Floating Signals ................................................................................................. 5

Measuring Ground-Referenced Signals............................................................................... 6

Measuring Temperature............................................................................................................... 6

Measuring Resistance .................................................................................................................. 7

Connecting Analog Output Signals ..................................................................................................... 7

Using the Function Generator.............................................................................................................. 8

Connecting Timing I/O Signals ........................................................................................................... 8

Using the Quadrature Encoder..................................................................................................... 10

Connecting User-Defined Signals ....................................................................................................... 10

Connecting Digital I/O Signals............................................................................................................ 11

Specifications....................................................................................................................................... 11

BNC-2120 Installation Guide 2 ni.com

Conventions

The following conventions are used in this document:

<> Angle brackets that contain numbers separated by an ellipsis represent a range of values

associated with a bit or signal name—for example, AO <3..0>.

»The »symbol leads you through nested menu items and dialog box options to a final action.

The sequence File»Page Setup»Options directs you to pull down the File menu, select the

Page Setup item, and select Options from the last dialog box.

This icon denotes a note, which alerts you to important information.

This icon denotes a caution, which advises you of precautions to take to avoid injury, data loss,

or a system crash. When this symbol is marked on a product, refer to the Read Me First: Safety

and Radio-Frequency Interference document for information about precautions to take.

bold Bold text denotes items that you must select or click in the software, such as menu items and

dialog box options. Bold text also denotes parameter names.

italic Italic text denotes variables, emphasis, a cross-reference, or an introduction to a key concept.

Italic text also denotes text that is a placeholder for a word or value that you must supply.

monospace Text in this font denotes text or characters that you should enter from the keyboard, sections

of code, programming examples, and syntax examples. This font is also used for the proper

names of disk drives, paths, directories, programs, subprograms, subroutines, device names,

functions, operations, variables, filenames, and extensions.

What You Need to Get Started

To set up and use your BNC-2120 accessory, you need the following:

❑BNC-2120 accessory/accessories1

❑BNC-2120 Installation Guide

❑One of the following DAQ devices:

– 68-pin E/M/S Series device (with one or two I/O connectors)2

– 100-pin E Series device

❑Cable(s) for DAQ device(s), as listed in Table 1

❑The E Series User Manual, the M Series User Manual, or the S Series User Manual

❑BNC cables

❑28–16 AWG wire

❑Wire strippers

❑Flathead screwdriver

Installing the BNC-2120

Figure 1 shows the front panel of the BNC-2120.

1 You can use two BNC-2120 accessories with both connectors of NI 6224/6229/6254/6259/6284/6289 M Series devices.

2 You cannot use the BNC-2120 with Connector 1 of NI 6225/6255 devices.

©National Instruments Corporation 3 BNC-2120 Installation Guide

Figure 1. BNC-2120 Front Panel

1 RES/BNC Switch (AI 3)

2 Resistor Measurement Screw

Terminals

3 Thermocouple Input Connector

4 Temperature Reference

5 BNC/Temp. Ref. Switch (AI 0)

6 BNC/Thermocouple Switch (AI 1)

7 Analog Input BNC Connectors

8 FS/GS Switches

9 Analog Output BNC Connector

10 Frequency Range Selection Switch

11 Sine/Triangle BNC Connector

12 TTL Square Wave BNC Connector

13 Sine/Triangle Waveform Switch

14 Frequency Adjust Knob

15 Amplitude Adjust Knob

16 Digital I/O Screw Terminals

17 Digital I/O LEDs

18 User-Defined Screw Terminals

19 User-Defined BNC Connectors

20 Timing I/O Screw Terminals

21 Quadrature Encoder Screw

Terminals

22 Quadrature Encoder Knob

23 Timing I/O BNC Connector

24 Power Indicator LED

Floating

Source (FS)

Ground Ref.

Source (GS)

ANALOG OUTPUTS

ANALOG INPUTS

DIGITAL I/O

FUNCTION GENERATOR

Frequency Selection

Amplitude Adjust

Sine /Triangle TTL Square Wave

Frequency Adjust

GSFS GSFS

AI 0 AI 1

USER 1

USER 2

P0.7

P0.6

P0.5

P0.4

P0.3

P0.2

P0.1

P0.0

D GND

AI 2

BNC

RES+

AI GND

AI SENSE

RES-

Temp.

Ref.

0.1-10 kHz

LO HI LO HI

1-100 kHz 13-1000 kHz

Thermo

couple

BNC

RES

AI 3

BNC

AI 3

AI 4 AI 5

AI 6 AI 7

AO 0 AO 1

USER-DEFINED

SIGNALS*

*For BNC connections, wire

anyTiming I/O or Digital I/O

screw terminals here.

PWR

BNC-2120

TIMING I/O

PFI 0 / P1.0

96 Puls es / Rev

Quadrature

Encoder

PFI 1 / P1.1

PFI 2 / P1.2

PFI 3 / P1.3

PFI 4 / P1.4

PFI 5 / P1.5

PFI 6 / P1.6

PFI 7 / P1.7

PFI 8 / P2.0

PFI 9 / P2.1

PFI 12 / P2.4

PFI 13 / P2.5

PFI 14 / P2.6

+5 V

PULSES

UP / DN

D GND

BNC-2120 Installation Guide 4 ni.com

To connect the BNC-2120 to your DAQ device, complete the following steps. Consult your computer or

PXI/PXI Express chassis user manual for specific instructions and warnings.

Note If you have not already installed your DAQ device, refer to the DAQ Getting Started Guide for

instructions.

Caution Do not connect the BNC-2120 to any device other than National Instruments E/M/S Series

multifunction DAQ devices. Doing so can damage the BNC-2120, the DAQ device, or the host

computer. National Instruments is not liable for damage resulting from these connections.

1. Place the BNC-2120 near the host computer or PXI/PXI Express chassis or use the optional DIN

Rail Mounting kit for UMI-FLEX-6 and BNC boxes (part number 777972-01), which you can

order from National Instruments at ni.com.

Caution Do not connect input voltages greater than 42.4 Vpk/60 VDC to the BNC-2120. The

BNC-2120 is not designed for any input voltages greater than 42.4 Vpk/60 VDC, even if a

user-installed voltage divider reduces the voltage to within the input range of the DAQ device. Input

voltages greater than 42.4 Vpk/60 VDC can damage the BNC-2120, all devices connected to it, and

the host computer. Overvoltage can also cause an electric shock hazard for the operator. National

Instruments is not liable for damage or injury resulting from such misuse.

2. Connect the BNC-2120 to the DAQ device using the appropriate cable for your DAQ device,

as listed in Table 1.

The power indicator LED, shown in Figure 1, lights. If it does not light, check the cable

connections.

3. Launch Measurement & Automation Explorer (MAX), confirm that your DAQ device is

recognized, and configure your device settings. Refer to the DAQ Getting Started Guide for more

information.

4. Connect signals to the BNC connectors and screw terminal block as described in the following

sections.

Note With NI-DAQmx, National Instruments has revised its terminal names so they are easier to

understand and more consistent among NI hardware and software products. The revised terminal

names used in this document are usually similar to the names they replace. For a complete list of

Traditional NI-DAQ (Legacy) terminal names and their NI-DAQmx equivalents, refer to the

Terminal Name Equivalents table in the NI-DAQmx Help.

Table 1. BNC-2120 Cabling Options

Number of Pins DAQ Device Recommended Cable(s)

68-pin DAQCard E Series,

NI PCI/PCIe/PXI/PXIe M Series*

NI 6143 S Series

SHC68-68-EPM or RC68-68

PCI/PXI E Series,

USB Mass Termination M Series*,

NI 611x/612x/613xS Series†

SH68-68-EPM or R6868†

100-pin PCI/PXI E Series SH1006868

*You cannot connect the BNC-2120 to Connector 1 of NI 6225/6255 devices.

†Do not use the R6868 cable with NI 6115/6120 S Series devices; use only the SH68-68-EPM cable.

©National Instruments Corporation 5 BNC-2120 Installation Guide

5. Test specific device functionality, such as the ability to send and receive data with MAX test panels.

Refer to the DAQ Getting Started Guide for detailed information about running test panels in

MAX.

When you have finished using the BNC-2120, power off any external signals connected to the

BNC-2120 before you power off your computer.

Connecting Analog Input Signals

You can use the analog input BNCs on the BNC-2120 in the following ways:

• Measure differential AI signals, as described in the Connecting Differential Analog Input Signals

section

• Measure temperature, as described in the Measuring Temperature section

• Measure resistance, as described in the Measuring Resistance section

Connecting Differential Analog Input Signals

Use the BNC-2120 BNC connectors on the front panel to connect AI <0..7> signals to your DAQ device.

The BNC-2120 is only intended for differential analog input signals. The number of connectors you use

depends on your DAQ device and application. Complete the following steps to measure a differential

(DIFF) analog input signal.

1. Connect the BNC cable to one of the AI <0..7> BNC connectors on the front panel.1

2. If you are using AI 0, move the BNC/Temp. Ref. switch to the BNC position.

If you are using AI 1, move the BNC/Thermocouple switch to the BNC position.

If you are using AI 3, move the RES/BNC switch to the BNC position.

3. Configure your software to measure the channel differentially.

4. Move the FS/GS switch to the applicable position, depending on whether you are measuring a

floating source (FS) or ground-referenced source (GS) analog input signal. Refer to the Measuring

Floating Signals and Measuring Ground-Referenced Signals sections for more information about

these signal sources.

Measuring Floating Signals

To measure floating signal sources, move the corresponding switch below the BNC connector to the FS

position. In the floating source switch position, the DAQ device’s amplifier negative terminal connects

to ground through a 4.99 kΩresistor, as shown in Figure 2. Refer to your DAQ device documentation

for more information about measuring floating signals.

1 When using the BNC-2120 with Connector 1 of NI 6224/6229/6254/6259/6284/6289 devices, the AI <0..7> BNCs on the

BNC-2120 map to the AI <16..23> channels on the M Series device.

BNC-2120 Installation Guide 6 ni.com

Figure 2. Measuring a Floating Signal Source

Measuring Ground-Referenced Signals

To measure ground-referenced signals, move the switch below the BNC connector for the AI channel

you are using to the GS position. Using the ground-referenced source switch position avoids ground

loops, as shown in Figure 3. Refer to your DAQ device documentation for more information about

measuring ground-referenced signals.

Figure 3. Measuring a Ground-Referenced Signal Source

AI GND and AI SENSE signals are located at the analog input screw terminals of the BNC-2120. When

connecting signals to the screw terminals, use 28–16 AWG wire with the insulation stripped to 0.28 in.

Measuring Temperature

You can measure temperature on the BNC-2120 with the temperature reference and thermocouple

connector.

To use the integrated circuit (IC) temperature reference on the BNC-2120, move the BNC/Temp. Ref.

switch above the AI 0 BNC to Temp. Ref. The integrated circuit (IC) temperature reference provides

built-in cold-junction compensation (CJC) through software. The IC sensor voltage is linearly

proportional to the sensor temperature where:

°C = Volts ×100

The sensor is accurate to ±1.5 °C.

To use the thermocouple on the BNC-2120, move the BNC/Thermocouple switch above the AI 1 BNC

to Thermocouple. You can connect any type of thermocouple with a two-prong miniature or

subminiature male connector to the thermocouple connector.

–

Signal

Source BNC-2120

DAQ Device

(Differential Input Mode)

AI GND

–

4.99 kΩ

FSMode

0.1 μF

–

Signal

Source BNC-2120

DAQ Device

(Differential Input Mode)

AI GND

–

4.99 kΩ

GSMode

0.1 μF

©National Instruments Corporation 7 BNC-2120 Installation Guide

For more information on thermocouples and CJC, refer to the Developer Zone document, Taking

Thermocouple Temperature Measurements, by going to ni.com/info and entering the info code

rdtttm.

Measuring Resistance

You can measure resistance with the analog input screw terminals on the BNC-2120. Figure 4 is a

schematic representation of how the BNC-2120 measures resistance.

Figure 4. Measuring Resistance on the BNC-2120

RES+ is internally connected to AI 3 and VCC. RES– is internally connected to AI 11. There is also a

10 kΩresistor between AI 11 and AI GND.

When connecting signals to the screw terminals, use 28–16 AWG wire with the insulation stripped

to 0.28 in.

Complete the following steps to measure resistance.

1. Move the RES/BNC switch above the AI 3 BNC to the RES position.

2. Configure your software to measure AI 3 and AI 11 in referenced single-ended (RSE) mode.

3. Connect the resistor to the RES+ and RES– screw terminals.

You can measure resistors with values ranging from 100 Ωto 1 MΩ.

4. Measure VCC on AI 3 and the voltage drop across the internal 10 kΩresistor on AI 11.

5. With these measurements, calculate the resistor value using the following formula:

Connecting Analog Output Signals

Use the AO <0..1> BNC connectors on the BNC-2120 front panel to connect analog output signals to

your DAQ device.1The number of connectors you use depends on your DAQ device and application.

Refer to your DAQ device documentation for information about the use of these signals.

1 When using the BNC-2120 with Connector 1 of NI 6229/6259/6289 devices, the AO <0..1> BNCs on the BNC-2120 map to

the AO <2..3> channels on the M Series device.

RES+ AI 3

BNC-2120

VCC

User Resistor

Screw

Terminals

AI 11

AI GND

AI SENSE

RES–

10 kΩ

0.5%

Resistor Value

VAI 3 VAI 11

–

VAI 11 10 kΩ()⁄

---------------------------------------=

BNC-2120 Installation Guide 8 ni.com

Using the Function Generator

The BNC-2120 has a function generator that produces sine or triangle waveforms and TTL-compatible

square waveforms. Use the switch below the Sine/Triangle BNC to select a sine wave or triangle wave

output for the connector. A TTL-compatible square wave is always present at the TTL Square Wave

BNC.

To adjust the frequency of the function generator, select your frequency range using the Frequency

Selection switch. You can select 0.1–10 kHz, 1–100 kHz, or 13–1000 kHz. The Frequency Adjust knob

adjusts the frequency within the preselected range for the sine or triangle wave and the TTL square wave

outputs.

The Amplitude Adjust knob adjusts the amplitude of the sine or triangle wave output up to 4.4 Vp-p.

Connecting Timing I/O Signals

Connect the timing I/O signals of your DAQ device to the PFI 0/P1.0 (AI START TRIG) BNC or the

timing I/O screw terminals on the BNC-2120. When connecting signals to the screw terminals, use

28–16 AWG wire with the insulation stripped to 0.28 in.

Table 2 describes the timing I/O BNC and terminal signals on the BNC-2120.

Table 2. BNC-2120 Timing I/O BNC/Terminal Descriptions

BNC/Terminal Description

PFI 0/P1.0 Programmable Function Input channel 0 or Port 1 Digital Input/Output channel 0

AI START TRIG (AI Start Trigger Signal)—As an output, this pin is the ai/StartTrigger

signal. In post-trigger DAQ sequences, a low-to-high transition indicates the initiation of

the acquisition sequence. In applications with pre-trigger samples, a low-to-high transition

indicates the initiation of the pre-trigger samples.

PULSES Refer to the Using the Quadrature Encoder section for information about using these

terminals.

UP/DN

PFI 1/P1.1 Programmable Function Input channel 1 or Port 1 Digital Input/Output channel 1

AI REF TRIG (AI Reference Trigger Signal)—As an output, this pin is the

ai/ReferenceTrigger signal. In applications with pretrigger samples, a low-to-high

transition indicates the initiation of the post-trigger samples. AI Reference Trigger

is not used in applications with posttrigger samples.

PFI 2/P1.2 Programmable Function Input channel 2 or Port 1 Digital Input/Output channel 2

AI CONV CLK (AI Convert Clock Signal)—As an output, this pin is the ai/ConvertClock

signal. A high-to-low edge on AI CONV indicates that an A/D conversion is occurring.

PFI 3/P1.3 Programmable Function Input channel 3 or Port 1 Digital Input/Output channel 3

CTR 1 SOURCE (Counter 1 Source Signal)—As an output, this pin is the Ctr1Source

signal. This signal reflects the actual source connected to the general-purpose counter 1.

©National Instruments Corporation 9 BNC-2120 Installation Guide

PFI 4/P1.4 Programmable Function Input channel 4 or Port 1 Digital Input/Output channel 4

CTR 1 GATE (Counter 1 Gate Signal)—As an output, this pin is the Ctr1Gate signal.

This signal reflects the actual gate signal connected to the general-purpose counter 1.

PFI 5/P1.5 Programmable Function Input channel 5 or Port 1 Digital Input/Output channel 5

AO SAMP CLK (AO Sample Clock Signal)—As an output, this pin is the ao/SampleClock

signal. A high-to-low edge on AO SAMP indicates that the AO primary group is being

updated.

PFI 6/P1.6 Programmable Function Input channel 6 or Port 1 Digital Input/Output channel 6

AO START TRIG (AO Start Trigger Signal)—As an output, this pin is the ao/StartTrigger

signal. In timed AO sequences, a low-to-high transition indicates the initiation of the

waveform generation.

PFI 7/P1.7 Programmable Function Input channel 7 or Port 1 Digital Input/Output channel 7

AI SAMP CLK (AI Sample Clock Signal)—As an output, this pin is the ai/SampleClock

signal. This pin pulses once at the start of each AI sample in the interval sample.

A low-to-high transition indicates the start of the sample.

PFI 8/P2.0 Programmable Function Input channel 8 or Port 2 Digital Input/Output channel 0

CTR 0 SOURCE (Counter 0 Source Signal)—As an output, this pin is the Ctr0Source

signal. This signal reflects the actual source connected to the general-purpose counter 0.

PFI 9/P2.1 Programmable Function Input channel 9 or Port 2 Digital Input/Output channel 1

CTR 0 GATE (Counter 0 Gate Signal)—As an output, this pin is the Ctr0Gate signal.

This signal reflects the actual gate signal connected to the general-purpose counter 0.

PFI 12/P2.4 Programmable Function Input channel 12 or Port 2 Digital Input/Output channel 4

CTR 0 OUT (Counter 0 Output Signal)—As an input, this pin can be used to route signals

directly to the RTSI bus. As an output, this pin emits the Ctr0InternalOutput signal.

PFI 13/P2.5 Programmable Function Input channel 13 or Port 2 Digital Input/Output channel 5

CTR 1 OUT (Counter 1 Output Signal)—As an input, this pin can be used to route signals

directly to the RTSI bus. As an output, this pin emits the Ctr1InternalOutput signal.

PFI 14/P2.6 Programmable Function Input channel 14 or Port 2 Digital Input/Output channel 6

FREQ OUT (Frequency Output)—This output is from the frequency generator.

+5 V +5 V Power—These terminals are fused on the DAQ device and are self-resetting.

The current available depends on the product to which it is connected.

D GND Digital Ground—This terminal supplies the reference for the digital signals at the

I/O connector as well as the +5 VDC supply.

Table 2. BNC-2120 Timing I/O BNC/Terminal Descriptions (Continued)

BNC/Terminal Description

BNC-2120 Installation Guide 10 ni.com

Using the Quadrature Encoder

The BNC-2120 contains a mechanical quadrature encoder circuit that produces 96 pulses per encoder

revolution. Two outputs, PULSES and UP/DN, are at the screw terminals located below the quadrature

encoder knob.

PULSES outputs a pulse train generated by rotating the encoder shaft. It provides four pulses per one

mechanical click of the encoder. UP/DN outputs a high or a low signal indicating rotation direction.

When the direction is counterclockwise, UP/DN is low. When the direction is clockwise, UP/DN is high.

To use the quadrature encoder with counter 0 of the DAQ device, connect the PULSES terminal to PFI 8

and connect the UP/DN terminal to the P0.6 digital I/O terminal, the up/down pin of counter 0. To use

the quadrature encoder with counter 1, connect the PULSES terminal to PFI 3 and connect the UP/DN

terminal to the P0.7 digital I/O terminal, the up/down pin of counter 1. Refer to Table 2 for more

information about PFI 3 and PFI 8. Refer to the Connecting Digital I/O Signals section for more

information about the digital I/O terminals and LEDs.

You can use the Count Digital Events VI from the LabVIEW Example Finder (Hardware Input and

Output»DAQmx»Counter Measurements»Count Digital Events) with the BNC-2120 quadrature

encoder. After opening the VI, select Externally Controlled in the Count Direction control. The VI

retrieves the count from the counter. You can convert the count into total degrees rotated using the

following formula:

Total Degrees Rotated = PULSES ×3.75°/pulse

where

3.75°/pulse = 360°/96 pulses

Calculate the number of revolutions and remaining degrees by dividing the total degrees rotated by 360°.

The calculated quotient is equal to the number of revolutions and the remainder is equal to the remaining

degrees.

Connecting User-Defined Signals

The USER 1 and USER 2 BNC connectors allow you to use a BNC connector for a digital I/O or

timing I/O signal of your choice. The USER 1 and USER 2 BNC connectors are routed (internal to

the BNC-2120) to the USER 1 and USER 2 screw terminals, as shown in Figure 5.

Figure 5. USER <1..2> BNC Connections

Figure 5 shows an example of how to use the USER 1 and USER 2 BNCs. To access the PFI 8/P2.0

(CTR 0 SOURCE) signal from a BNC, connect USER 1 on the screw terminal block to PFI 8/P2.0 with

a 28–16 AWG wire.

USER 2 BNC

Internal

Connection

USER 1 BNC

D GND

USER 2

USER 1

D GND

Internal

Connection

Andere Handbücher für BNC-2120

Inhaltsverzeichnis

Andere National Instruments Klemmenblock Handbücher

National Instruments

National Instruments PXIe-4310 Bedienungsanleitung

National Instruments

National Instruments NI TB-2634 Bedienungsanleitung

National Instruments

National Instruments SCXI-1384K Bedienungsanleitung

National Instruments

National Instruments NI TB-2630B Bedienungsanleitung

National Instruments

National Instruments NI SCXI -1339 Bedienungsanleitung

National Instruments

National Instruments VXI-TB-1303 Bedienungsanleitung

National Instruments

National Instruments TB-2627 Bedienungsanleitung

National Instruments

National Instruments SCXI -1305 Bedienungsanleitung

National Instruments

National Instruments 776572-1600 Bedienungsanleitung

National Instruments

National Instruments SCXI-1321 Bedienungsanleitung

National Instruments

National Instruments TBX-1316 Bedienungsanleitung

National Instruments

National Instruments PXI TB-2705 Bedienungsanleitung

National Instruments

National Instruments SCXI-1303 Bedienungsanleitung

National Instruments

National Instruments NI TB-9214 Handbuch

National Instruments

National Instruments NI TB-2631B Bedienungsanleitung

National Instruments

National Instruments TB-2643 Bedienungsanleitung

National Instruments

National Instruments TB-2630 Bedienungsanleitung

National Instruments

National Instruments NI TB-2627 Bedienungsanleitung

National Instruments

National Instruments SCXI-1300 Bedienungsanleitung

National Instruments

National Instruments SCXI-1305 Bedienungsanleitung

National Instruments

National Instruments TBX-68S Bedienungsanleitung

National Instruments

National Instruments Terminal Block NI TB-2706 Bedienungsanleitung

National Instruments

National Instruments NI TB-2630 Bedienungsanleitung

National Instruments

National Instruments SCXI-1338 Bedienungsanleitung

Beliebte Klemmenblock Handbücher anderer Marken

Russound

Russound EZB-1SC Bedienungsanleitung

Siemens

Siemens MOBY FC 56 Stücklistenhandbuch

Panasonic

Panasonic TY-FB8TA Bedienungsanleitung

NI SCXI-1379 Bedienungsanleitung

ABB

ABB ZLS924 Benutzerhandbuch

Festo

Festo CPVSC1-EPR Series Bedienungsanleitung

Festo

Festo CPV -GE-DN2-8 Stücklistenhandbuch

Stahl

Stahl 8146/2 Bedienungsanleitung

Crestron

Crestron CLT-1FAN4 Bedienungsanleitung

Sony

Sony CBX-H11 Bedienungsanleitung

Festo

Festo CPX-FB38 Stücklistenhandbuch

Festo

Festo CPV -GE-ASI-8E8A-Z Series Stücklistenhandbuch

Festo

Festo MPA-S Series Stücklistenhandbuch

Hubbell

Hubbell BASETRAK PB2 Series Bedienungsanleitung

Crestron

Crestron CLT-2DIM2 Bedienungsanleitung

Omron

Omron XW2B-40J6-2B Bedienungsanleitung

Festo

Festo CPV GE-IL Series Stücklistenhandbuch

Lenz

Lenz XpressNet Digital plus LA152 Betriebsanleitung