NBB Nano-M SMJ Bedienungsanleitung

Receiver Type /

Version

Factory No.

Frequency

Transmitter Type /

Version

Factory No.

Frequency

Operating instructions

Nano-M SMJ USA/Canada

Compact-M

RADIO CONTROL SYSTEMS

OTTO-HAHN-STR. 3 - 5

DE-75248 ÖLBRONN-DÜRRN E-MAIL: [email protected]

INTERNET: www.nbb.de

TEL.: +49(0)7237/ 999-0

FAX: +49(0)7237/ 999-199

Table of contents

General information

Transmitter Nano-M SMJ

Receiver Compact-M

Accessories

Technical documents

The transmitter and receiver type, serial number, frequency range and approval for non-

EU countries are specified on the nameplates.

Please always specify the serial number for queries.

Example:

Never expose the radio control system to a strong jet from high pressure

cleaning equipment!

nTransmitter including carrying system

nReceiver with integrated mounting holes

nConnection cable for the receiver

The order confirmation and/or the delivery note when the system is received

is binding for the actual scope of delivery.

Even if you have already operated radio control systems, always read these

operating instructions before commissioning. Only these operating instructions

include the latest information about your NBB radio control system.

Please refer to the enclosed documents for explanations about the operating license.

Always observe the relevant work safety and accident prevention regulations. Only

trained and authorised persons may operate the NBB radio control system. The safety

features installed in the NBB radio control system must be checked regularly.

The NBB radio control system must be shut down immediately if there are

any faults. The transmitter must be switched off using the EMERGENCY STOP

switch or the STOP key. The connection cable must be disconnected at the

receiver of the connection socket (terminal) of the controlled system. The

radio control system may only be repaired by NBB or specialists authorised

by NBB.

Disregard of these recommendations puts you and others in danger! NBB refuses any

warranty or liability in such cases. This radio control system is only suitable for the

control of construction machines and industrial systems. The applied safety measures

(EMERGENCY STOP, zero position) are only fully effective in this application area. Any

different use is not permitted and releases NBB from any responsibility.

Transmitter Type / Version:

Factory No.:

Frequency:

Nano-L SMJ

999 899 4990

402 -470 MHz

Receiver Type / Version:

Factory No.:

Frequency:

Compact-V

999 899 4990

402 -470 MHz

Standard scope of delivery

Safety information

Nameplates

General information

Your NBB radio control system is maintenance-free to a large extent. Nevertheless

observe the following points:

nRegularly check the EMERGENCY STOP and STOP function.

nRemove remnants of building material.

nDisconnect receiver from the power supply for arc welding work, otherwise there

is a risk of damage to the receiver electronics.

nRegularly check wear parts.

NBB grants a functional warranty of 12 months from the date of sale on all NBB radio

control systems (transmitter, receiver, charger). Working hours and material costs are

included in the warranty. Shipping costs shall be at the expense of the buyer. Wear

parts, relays, rechargeable batteries and batteries are excluded from the warranty.

The functional warranty will become null and void for damage, accidental damage,

negligence, improper use, non-compliance of the operating conditions, non-observance

of the operating, test and service information as well as for repairs or device

modifications that are not authorised by NBB.

NBB is not liable for indirect damage and reserves the right to decide on improvements

or replacements.

If a fault event occurs with the NBB radio control system, cease work immediately!

Please note that even small faults can represent the beginning of extensive defects.

Always contact your dealer or NBB in the event of a fault. Do not attempt to repair the

NBB radio system yourself, irreparable damage may occur.

Maintenance

Warranty

In the event of faults

Variations

Transmitter Nano-M SMJ

Nano-M SMJ with a display and

2 joysticks

Nano-M SMJ with 3 joysticks

Nano-M SMJ with a display and

8 joysticks

Nano-M SMJ with 6 joysticks

Nano-M SMJ with a display and

3 joysticks

Nano-M SMJ with 4 joysticks

Nano-M SMJ 7.2 V accumulator

system

Operating voltage 7.2 V:

Insert the battery in the battery compartment for commissioning.

For removal, press in the locking pin to unlock and slide out the battery to the side.

If the NBB radio control system is not to be used for a long time, it is strongly

recommended to charge the battery approx. every 4 weeks. This prevents deep

discharge of the battery and enhances its service life. If you decommission the

NBB radio control system for a long time, we recommend that you remove the

batteries from the transmitter!

Safety equipment in the NBB radio control system:

nEMERGENCY STOP or STOP function

nZero position interlock

nAddressing each transmitter using a unique bit combination

nRubber sleeves to protect the switch

Please check the sleeves and the housing for breaks and cracks each time before

commissioning the transmitter. Contact your service team if necessary. Non-observance

can cause malfunctions and water damage.

Commissioning

Safety equipment

Press in the locking pin

and slide out the battery

Please refer to the technical annex for the exact design.

Completely charge the rechargeable battery before initial use.

Switching the transmitter on and off

Design with emergency stop

Unlock the Emergency Stop pushbutton by turning clockwise to switch on the

transmitter.

Two short signals can be heard.

A red dot flashes in the LED display and an antenna symbol appears in the LC display

during operation.

The transmitter is switched off by pressing the Emergency Stop pushbutton once.

After pressing the EMERGENCY STOP switch, stop telegrams are sent for 2 seconds

to switch off the system. This shut-off time is displayed on the LED display by the

segments rotating clockwise.

Toensurefaultlessoperation,pleaseobservethefollowingrulesforoperation precisely:

The system to be controlled - provided the transmitter is ready for operation - can only

be switched on if no command transmitters are activated. The command necessary

for this is activated by the «On/Horn» key. Here a horn signal is triggered for the

system to be controlled. After switching on the system to be controlled, this key

is used, according to the work specifications, for repeated triggering of the horn

signal.

Frequency switching:

To switch the frequency, press and hold the «On/Horn» key. Now press the «Frequency

switching» key successively. If the receiver locks on a new frequency, a horn signal can

be heard and the system is ready for operation.

Please observe the country-specific regulations, if applicable.

The system can also be equipped with automatic frequency switching (LBT) as an option.

Operation of the system

Operation:

The red dot flashes.

FREQUENCY

SWITCHING

ON/HORN

FREQUENCY SWITCHING

Channel number:

During operation, the set channel can be displayed by pressing the «Frequency swit-

ching» key.

Operation of the system

Please refer to the technical annex for the exact position of the «On/Horn» and

«Frequency switching» keys.

Battery life warnings:

The LED display of the active battery flashes green during operation. When the control

lamp flashes orange, the battery indicates a remaining capacity of approx. 10%. The de-

pletion of the battery capacity is indicated by the red control lamp lighting up. To replace

the depleted battery place the system on a solid, level surface with access to the bottom

at the system. Remove the spent battery and replace with a fully charged battery. The

radio system will not have an interruption in contol during battery replacement provided

the second battery is installed and has capacity left. Only charge the discharged battery

in the charger.

Battery display:

LED - flashes green: Battery OK and in operation.

 LED - flashes orange: Battery capacity left around 10%.

LED - flashes red: Battery capacity left around 5%.

LED - permanently lights up red: Battery empty, transmitter switches to

2nd battery.

Energy saving function:

If no keys are pressed within a specified time*, the transmitter automatically switches

off. The red dot in the LED display goes out.

A transmitter can also be manufactured without a standby function for continuous

operation as an option.

*The standby time can be set as desired.

LED battery left

LED battery right

Changing the Surface Mounted Joystick:

Switch off the transmitter and remove the batteries.

Loosen all 4 screws of the Surface Mounted Joystick with a Torx 10 screwdriver and

remove the screws.

Remove the Surface Mounted Joystick from the top.

Insert the new Surface Mounted Joystick and make sure that the plugs and sockets

are above each other. Screw down the Surface Mounted Joystick with the 4 screws

previously removed and reinsert the batteries.

Start teach mode after changing the Surface Mounted Joystick.

Surface Mounted Joystick teach mode activation with pushbutton:

4. .

Technology SMJ - Surface Mounted Joystick

To activate teach mode, the transmitter must be switched off.

Press and hold the «Frequency switching» key.

Switch the transmitter on.

The letters «Jt» appear in the display after 2 seconds.

Now release the «Frequency switching» key.

Completely move the Surface Mounted Joystick in one direction and return it to

the 0-position. Repeat this for all directions. Perform point 5 for all other Surface

Mounted Joystick if required. Reactivation of teach mode is not required.

Press the «On/Horn» key once. Teach mode will be closed and the new Surface

Mounted Joystick will function as intended by the system design.

Attention! The transmitter is now in working mode!

Error: If «Jt» does not appear in the display, please switch off the transmitter and

start teach mode activation from the beginning!

Surface Mounted Joystick teach mode activation with pushbutton and display:

The TEACH MODE, memory of max. and min.-values of the valves adjustment with

proportional control, is activated by a separate combination of keys.

Please refer to the technical annex.

Nano-M SMJ

See nameplate

Switchable frequency to respective national band possible as a result of synthe-

sizer technology.

Addressing each transmitter using a unique bit combination

FSK - Signal acc. to CCITT V.23

1200 -9600 baud (bit / sec.)

Approx. 300 - 1000 m (depending on environment)

Accumulateur 7.2 V NBB

60 - 100 mA

<10 mW ERP

IP 65

From -20 to +65 °C

3500 g

354 x 229 x 141 mm

Technical data

Transmitter

Transmission frequency range

Data security

LF-modulation

Baud rate

Range

Operating voltage

Current consumption

RF output

Protection class

Operating ambient temperature

Weight (without battery)

Measurements (L x W x H)

Technology SMJ - Surface Mounted Joystick

To activate teach mode, the transmitter must be switched off.

Press and hold the «Frequency switching» key.

Switch the transmitter on.

«Joy Teach» with graphics appears in the display after 2 seconds.

Now release the «Frequency switching» key.

Completely move the Surface Mounted Joystick in one direction and return it to

the 0-position. Repeat this for all directions. Perform point 5 for all other Surface

Mounted Joystick if required. Reactivation of teach mode is not required.

Press the «On/Horn» key once. Teach mode will be closed and the new Surface

Mounted Joystick will function as intended by the system design.

Attention! The transmitter is now in working mode!

Error: If «Joy Teach» does not appear in the display, please switch off the transmitter

again and start teach mode activation from the beginning!

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NBB Empfänger Handbücher

NBB

NBB Planar-D1 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung