NEC NP40CM Leitfaden

ISSUED: 11-01-06 SHEET #: 055-9478-6 01-14-09

Visit the Peerless Web Site at www.peerlessmounts.com

1 of 8 For customer care call 1-800-729-0307 or 708-865-8870.

Read instruction sheet before you start installation and assembly.

Maximum Load Capacity: 50 lb (22.7 kg)

IMPORTANT! Be sure not to touch the projector while tightening the set screw on the

ball and socket mount. This may cause the image to be unaligned when you let go.

Applications:

FlushMount.................................................................................................................................................. page 5

ExtensionColumn........................................................................................................................................ page 6

Installations:

To Wood Joist Finished Ceilings,

Exposed Wood Joists, or Wood Beam Ceilings........................................................................................ page 3

To Concrete Ceilings.................................................................................................................................... page 4

IMPORTANT! Turn to the appropriate page for your ceiling installation.

• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattachedhardwareand

components.

WARNING

This product is intended for use with UL

Listed products and must be installed by a

qualified professional installer.

NEC DISPLAY SOLUTIONS OF AMERICA, INC.

Model: NP40CM

Installation andAssembly -Ceiling Mount for

NEC NP 40/41/50/60/61/62/100/200 Projectors

ISSUED: 11-01-06 SHEET #: 055-9478-6 01-14-09

Visit the Peerless Web Site at www.peerlessmounts.com 2 of 8 For customer care call 1-800-729-0307 or 708-865-8870.

Parts List

Before you start check the parts list to insure all of the parts shown are included.

Note: Actual parts may appear slightly different than illustrated.

Description Qty. Part Number

Aball and socket mount 1 055-0016

B4 mm security allen wrench 1 560-9646

CM5 x .8 x 10 mm socket pin type F screw 1 520-2031

D#10-32 x 3/8" spade thumb screw 1 560-2107

E#10-32 x 3/8" serrated washer head socket pin screw 1 520-2151

F#14 x 2.5 phillips hex head wood screw 2 5S1-015-C04

Gceilingplate 1 580-4042

H.25" ID x .56" OD x .26 spacer 2 590-2071

Iextensioncolumn connector withcord management 1 580-4025

J#10-32 x 3/8" socket pin screw 2 520-2084

K#10-32 x 3/16" slotted set screw 3 520-2187

Ladapterplate 1 055-4808

MM3 x 16 mm serrated socket pin screw 1 510-2083

NM3 x 25 mm serrated socket pin screw 3 510-2127

O.156 x .375 retaining spacer 1 590-2140

P.198 x .750 retaining spacer 3 590-2134

Q2 mm security allen wrench 1 560-1097

R.198 x .313 x .688 H retaining spacer 3 590-2131

ISSUED: 11-01-06 SHEET #: 055-9478-6 01-14-09

Visit the Peerless Web Site at www.peerlessmounts.com

3 of 8 For customer care call 1-800-729-0307 or 708-865-8870.

WOOD

JOIST

CEILING

Drill two 5/32" (4 mm) dia. holes to a minimum

depth of 2.5" (64 mm). Attach ceiling plate (G)

with two #14 x 2.5" (6 mm x 65 mm) wood

screws (F) as shown using 3/8" (10 mm) socket

wrench.

Skip to step 2.

IMPORTANT: Be sure to drill holes into the

joistCENTER!

For optional Cord Management,

installtwo spacers (H)between ceiling

plate(G)and ceiling.

Installation To Wood Joist Finished Ceilings,

Exposed Wood Joists, or Wood Beam Ceilings

WOOD

JOIST

CEILING

• Tighten wood screws (F) so that ceiling plate (G) is

firmlyattached, butdo notovertighten. Overtightening

candamage the screws,greatly reducing their holding

power.

• Never tighten in excess of 80 in • lb (9 N.M.).

• Make sure that mounting screws are anchored into the

center of the studs. The use of an "edge to edge" stud

finderis highlyrecommended.

WARNING

• It is the responsibility of the installer to verify that the

supportingsurface will safelysupport the combined

loadof allattached hardware andcomponents.

WARNING

ISSUED: 11-01-06 SHEET #: 055-9478-6 01-14-09

Visit the Peerless Web Site at www.peerlessmounts.com 4 of 8 For customer care call 1-800-729-0307 or 708-865-8870.

Drill two 1/4" (6 mm) dia. holes to a minimum depth of

2.5" (64 mm). Attach ceiling plate (G) using two

concrete anchors and #14 x 2.5" wood screws (F) as

shown in Illustration A and 1, 2, and 3 (below).

Tightenallfasteners.

IMPORTANT: It is the responsibility of the installer

to verify that the ceiling will safely support the

combined load of all attached hardware and

components.

CUTAWAYVIEW

INCORRECT

concrete

metal

bracket

plaster/

drywall

CORRECT

concrete

metal

bracket

plaster/

drywall

concrete

ceiling

concrete

anchor

concrete

anchor

concrete

anchor

Illustration A

Installation to Concrete Ceilings

ACC 203 (Alligator® concrete anchors) are recommended.

•FORDIRECTATTACHMENTTOLOAD BEARING

CONCRETEONLY!Concreteexpansionanchorsare

not intendedfor attachment to concrete ceilings

coveredwith a layerof plaster,drywall, orother

finishingmaterial. If mountingto concrete ceiling

coveredwith plaster /drywall is unavoidable,plaster /

drywallmust be counterboredas shown below.

WARNING

CONCRETECEILING

concrete

anchor

Drill hole and insert anchor

Place ceiling plate over anchor and secure with screw

After repeating step one tighten all fasteners

• Tighten wood screws so that ceiling plate is firmly

attached,but donot overtighten.Overtightening can

damagethe screws, greatlyreducing their holding

power.

• Never tighten in excess of 80 in • lb (9 N.M.).

• Make sure that mounting screws are anchored into the

center of the studs. The use of an "edge to edge" stud

finderis highlyrecommended.

WARNING

• When installing Peerless mounts on concrete, verify that you have a minimum of 1 5/8" of actual concrete surface in

the 1/4" diameter hole to be used for the concrete anchors. Do not drill into mortar joints! Concrete must meetASTM

C-90specifications.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Makesure that the supporting surface will safely supportthe combined load of the equipment and allattached hard-

wareand components.

• Neverexceed the Maximum UL Load Capacity of50 lb (27 kg).

WARNING

ISSUED: 11-01-06 SHEET #: 055-9478-6 01-14-09

Visit the Peerless Web Site at www.peerlessmounts.com

5 of 8 For customer care call 1-800-729-0307 or 708-865-8870.

Screw ball and socket mount (A) into ceiling plate (G).Align the notch with one of the four holes of the ceiling plate

(G) and secure ball and socket mount (A) with a M5 x 10 mm socket pin screw (C) using security allen wrench (B)

as shown in detail 1.

Note: Slotted set screw (K) is used to jam against the threads of the ball and socket mount to prevent any excess

movementof the balland socket mount(A).Do not overtightenscrew; overtightening screwwill damage threads

making it difficult to separate the products.

Skip to step 3.

Flush Mount Application

DETAIL 1

WOOD

CEILING

NOTCH

ISSUED: 11-01-06 SHEET #: 055-9478-6 01-14-09

Visit the Peerless Web Site at www.peerlessmounts.com 6 of 8 For customer care call 1-800-729-0307 or 708-865-8870.

Screw extension column to ceiling plate (G).

Align the notch with one of the four holes in

the ceiling plate (G) and secure extension

column with a M5 x 10 mm socket pin

screw(C) using securityallen wrench (B).

See detail 4.

Screw extension column connector (I) to

extension column. Align slot in extension

column with one of the top holes in

extensioncolumn connector(I). Insertand

tighten one #10-32 x 3/8" socket pin screw

(J)throughextensioncolumnconnector(I)

into slot on extension column using security

allen wrench (B). See detail 5.

Screw ball and socket mount (A) to

extension column connector (I). Align slot in

ball and socket mount (A) to one of the

bottom holes in extension column connector

(I). Insert and tighten one #10-32 x 3/8"

socket pin screw (J) through extension

column connector into slot in ball and

socket mount (A) using security allen

wrench (B). See detail 6.

Note: Slotted set screws (K) are used to

jam against the threads of each connecting

jointtoprevent anyexcess movement.Do

notovertightenscrews;overtightening

screws will damage threads making it

difficultto separate the products.

DETAIL 6

SLOT

DETAIL 5

DETAIL 4

EXTENSION

COLUMN

Installation to

Extension Column

EXTENSION

COLUMN

SLOT

EXTENSION

COLUMN

SLOT

EXTENSIONCOLUMN

(UL Listed EXT or ADJ

Series)

Sold Separately

ISSUED: 11-01-06 SHEET #: 055-9478-6 01-14-09

Visit the Peerless Web Site at www.peerlessmounts.com

7 of 8 For customer care call 1-800-729-0307 or 708-865-8870.

*Notchindicates front ofprojector.

Flip projector upside down and fasten three M3 x 25 mm socket pin screws (N) and three .198 x .313 x .688

retaining spacers (R) into the threaded inserts as indicated below. Finish tightening M3 x 25 mm socket pin

screws (N) using 2 mm security allen wrench (Q).

B. NECNP100/200

A. NECNP40/41/50/60/61/62

*Notchindicates front ofprojector.

Flip projector upside down and remove feet from bottom of projector. Fasten two M3 x 25 mm socket pin

screws (N) and two .198 x .750 retaining spacers (P) into the threaded inserts as indicated below. Fasten one

M3 x 16 mm socket pin screw (M) and one .156 x .375 retaining spacer (O) into the threaded insert as indi-

cated below. Finish tightening screws (N, M) using 2 mm security allen wrench (Q).

Find your projector from the models listed below

3-1

ISSUED: 11-01-06 SHEET #: 055-9478-6 01-14-09

Visit the Peerless Web Site at www.peerlessmounts.com 8 of 8 For customer care call 1-800-729-0307 or 708-865-8870.

To adjust roll, pitch, and yaw loosen the set screw

(shown below) using security allen wrench (B) or

standard 4 mm allen wrench. You should be able to

just slightly loosen the screw so that your adjustments

can be set without having to hold the projector. Move

projector to desired position and slowly tighten set

screw.

Note: Be sure not to touch the projector while

tightening the set screw. This may cause the image

to be unaligned when you let go.

IMPORTANT:Allen wrench is your key for projector

removal. Store it in a safe place.

Peerless offers several Projector Mounts to fit various

projectors. New Projector Mounts are continually being

developed to meet the demands of a growing projector

market. To find out if a mount is available for your particular

projector, call Peerless customer service at 1-800-729-

0307 or 1-708-865-8870.

Note: The projector adapter plate and projector you are installing may differ in appearance from the sample

illustrated below.

SETSCREW

Attach projector, with adapter plate already on it, to the

ball and socket mount (A) by inserting the ball and

socket mount (A) into the adapter plate connection and

twisting until the adapter plate will no longer turn

(about 75°). The spring loaded captive screw should

line up with a corresponding hole on the adapter plate

(this should line up automatically when the two are

connected). Push down and tighten the spring loaded

captive screw to secure the adapter plate to the mount.

If not using the optional security feature, fasten thumb

screw (D) in the hole opposite the spring loaded

captive screw.

OPTIONAL: For Armor Lock™security, insert serrated

washer head socket pin security screw (E) in the hole

opposite the spring loaded captive screw. Tighten with

security allen wrench (B). This will prevent the

projector from being removed.

Note: Be sure to only use the #10-32 x 3/8" screw (E)

(or the thumb screw (D)) opposite the spring loaded

captive screw.

WOOD

JOIST

CEILING

PROJECTORADAPTERPLATE

(UL Listed PAP Series)

Sold Separately

PROJECTOR

WOOD

JOIST

CEILING

PROJECTOR

CUTAWAY VIEW OF

CEILINGPLATE (G)

CAPTIVE

SCREW

• Do not lift more weight than you can handle! Use

additionalman poweror mechanicallifting equipment

tosafely handle placementof the projector!

WARNING

Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NEC Rack & Stand Handbücher

NEC

NEC Video Wall Mount PD02VW MFS 46 55 L Leitfaden

NEC

NEC NP-M311W Leitfaden

NEC

NEC WM-46UN Wall Mount Portrait and Landscape Bedienungsanleitung

NEC

NEC T1000 - STAND MOUNTING Bedienungsanleitung

NEC

NEC PlasmaSync PX-60XM5A Bedienungsanleitung

NEC

NEC Video Wall Mount PD02VWXUN 46 L Bedienungsanleitung

NEC

NEC NP4000CM Bedienungsanleitung

NEC

NEC MultiSync V461 Bedienungsanleitung

NEC

NEC NP-PH1000U Bedienungsanleitung

NEC

NEC NEC W32-70 Bedienungsanleitung

NEC

NEC LCD8205 - MultiSync - 82" LCD Flat Panel... Bedienungsanleitung

NEC

NEC WMK-3255S Bedienungsanleitung

NEC

NEC WMK-3257 Leitfaden

NEC

NEC N8140-820 Bedienungsanleitung

NEC

NEC WM-46S-P Bedienungsanleitung

NEC

NEC MultiSync P701 Bedienungsanleitung

NEC

NEC WM-46UN-2X2 Bedienungsanleitung

NEC

NEC NP02LK Bedienungsanleitung

NEC

NEC WM-55UN-L Bedienungsanleitung

NEC

NEC NP-UM330W Series Leitfaden

NEC

NEC N8154-46 Bedienungsanleitung

NEC

NEC PA600CM Bedienungsanleitung

NEC

NEC NP600CM Leitfaden

NEC

NEC Wall Mount WMS32-55 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung