NEC 120Le Bedienungsanleitung
120Le Pentium III Processor
Installation Insert
PN: 455-01616-001
Proprietary Notice and Liability Disclaimer
The information disclosed in this document, including all designs and related materials, is
the valuable property of NEC Computers Inc. and/or its licensors. NEC Computers Inc.
and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights
to this document, including all design, manufacturing, reproduction, use, and sales rights
thereto, except to the extent said rights are expressly granted to others.
The NEC Computers Inc. product(s) discussed in this document are warranted in
accordance with the terms of the Warranty Statement accompanying each product.
However, actual performance of each such product is dependent upon factors such as
system configuration, customer data, and operator control. Since implementation by
customers of each product may vary, the suitability of specific product configurations and
applications must be determined by the customer and is not warranted by NEC Computers
Inc.
To allow for design and specification improvements, the information in this document is
subject to change at any time, without notice. Reproduction of this document or portions
thereof without prior written approval of NEC Computers Inc. is prohibited.
Trademarks
Intel and Pentium III are registered trademarks of Intel Corporation.
All other product, brand, or trade names used in this publication are the trademarks or registered
trademarks of their respective trademark owners.
PN: 455-01616-001 July 2001
Copyright 2001
NEC Computers Inc.
15 Business Park Way
Sacramento, CA 95828
All Rights Reserved
120Le Pentium III Processor Installation 3
Introduction
This Intel® Pentium® III Processor Installation Insert provides information for
installing the Pentium III processor upgrade into your 120Le system. Read this
procedure in its entirety before performing the installation to become familiar
with the items in this upgrade and the sequence of steps you will perform.
Unpacking the Upgrade
When you receive your Pentium III processor upgrade, inspect the shipping
container prior to unpacking. If the shipping box is damaged, note the damage,
and if possible, photograph it for reference. After removing the contents of the
container, keep the carton and the packing materials. If the contents appear
damaged when you unpack the box, file a damage claim with the carrier
immediately.
Installing the Upgrade
!
CAUTION
Observe static precautions. Use an antistatic wrist strap.
Hold the processor only by its edges. Do not touch the pins
of the processor board.
!
CAUTION
Installing a second processor that is of a different type than
the first processor will result in system damage. Do not
touch or bend the processor's exposed pins.
Note: When adding a second processor to your system,
you must remove the terminator from the secondary
processor socket. Also, you must install a VRM into the VRM
socket on the system board.
4 120Le Pentium III Processor Installation
Opening and Removing the Front Door (Tower Version)
You must open the front door to remove the left side panel on your system.
Perform this procedure to open and remove the front door.
1. Power off the system and ensure the power cord is unplugged from the AC
wall outlet.
2. If the front door is locked, unlock it.
3. Grasp the indentation located on the right edge of the front door and pull the
door towards you to open it (Figure 1).
Figure 1. Opening the Front Door
4. To remove the front door, open it and lift the door and pull it towards you
(see Figure 2). The mounting pins of the front door are disengaged from the
mounting holes on the front of the system.
Figure 2. Removing the Front Door
120Le Pentium III Processor Installation 5
Removing Side Panel
To install options in your system, you must remove the side panel on the left
side of the system (as viewed from the front).
!
CAUTION
For proper cooling and airflow, do not operate the system
with the side panels removed. Always replace the panels
before powering on the system.
!
WARNING
If you are removing the side panel after the system is set up,
you must first power off the system and all external devices
and then Unplug the system power cord
To remove the left side panel:
1. The left side panel is secured to the chassis with one thumbscrew
(Figure 3, A). Remove the screw securing the side panel. Save the screw for
reattaching the side panel.
2. Using the indentation on the side of the panel, slide the side panel toward the
front of the system. This unlocks the locking fingers behind the side panel.
3. Pull the side panel out and away from the chassis (Figure 3).
A
Figure 3. Removing the Left Side Panel
6 120Le Pentium III Processor Installation
Removing the Air Duct
To install processor upgrade into your system, you must remove the system air
duct. See Figure 4.
!
CAUTION
For proper cooling and airflow, do not operate the system
with the air duct removed. Always replace the air duct and
the side panels before powering on the system.
To remove the air duct:
1. Pull the air duct plunger (Figure 4, B) to release the air duct from the system
chassis.
2. Pull the air duct out and away from the chassis (Figure 4, A).
AB
C
Figure 4. Removing the Air Duct
Installing the Processor Upgrade
1. Raise the secondary processor socket ZIF lever to the up position. See
Figure 5.
2. Remove the terminator from the secondary processor socket.
3. Position the processor over its ZIF socket so the processor pins align with
the socket holes. Note that one corner of the processor has three pins that
should be positioned over the corner of the socket that has the three
matching pin holes. See Figure 5, A.
120Le Pentium III Processor Installation 7
A
Figure 5. Positioning the Processor
4. Insert the processor pins into the socket. Apply pressure equally over the top
surface of the processor until it seats in the socket. The processor should
easily fit, do not force the processor into the socket.
5. Lower the ZIF socket lever into the locked position. See Figure 6.
Figure 6. Installing the Processor
8 120Le Pentium III Processor Installation
!
CAUTION
The thermal pad is very delicate and tears easily. Handle
with extreme care. Perform the next two steps exactly as
described to ensure proper heat transfer from the processor
to the heat sink.
6. One side of the thermal pad is shiny metallic foil. The other side of the
thermal pad is covered with a clear plastic liner. Carefully peel the liner
away from the pad. The clear liner is not used and may be discarded.
7. Position the thermal pad on top of the processor with the shiny side facing
down and the yellow sticky side of the pad facing up. Ensure the pad is
positioned over the center of the processor as shown in Figure 7.
Figure 7. Installing Thermal Pad
8. Ensure the small end of the heat sink clip is positioned into the heat sink as
far as it will go.
Note: The heat sink included with this upgrade may not
resemble the heat sink on the processor in your system.
Several types of heat sinks are used with the Pentium III
processor.
!
CAUTION
When performing the next three steps, be sure the heat sink
is positioned as shown and is held firmly in place. If the heat
sink should slide across the top of the processor, the thermal
pad may be damaged. In the next step, the heat sink must
be gently lowered onto the processor, being careful not to
move the heat sink from side to side.
120Le Pentium III Processor Installation 9
9. The bottom of the heat sink is not completely flat, and instead has an L-
shaped groove along two sides of the bottom. Position the heat sink over the
processor so that the long side of the groove covers the rear plastic edge of
the socket and the adjacent side of the groove covers the socket lever. See
Figure 8. Gently lower the heat sink onto the processor, being careful not to
move the heat sink from side to side.
Plastic part
Lever
Lever L-Shaped groove
L-Shaped groove
Plastic part
Top View
Heat sink
Lever
L-Shaped groove
(shaded area)
Side View
Figure 8. Positioning the Heat Sink Clip
10 120Le Pentium III Processor Installation
10.Attach the small end of the heat sink clip to the tab located on the base of the
ZIF socket. See Figure 9, A.
A
A
Figure 9. Positioning the Heat Sink Clip.
Inhaltsverzeichnis
Andere NEC Server Handbücher
NEC
NEC MH4500 Bedienungsanleitung
NEC
NEC Express5800/R120e-2E Bedienungsanleitung
NEC
NEC EXP339 Bedienungsanleitung
NEC
NEC Univerge SV8100 Bedienungsanleitung
NEC
NEC Express5800/T120e Bedienungsanleitung
NEC
NEC Express5800/1020Ba Bedienungsanleitung
NEC
NEC Univerge SV8100 Benutzerhandbuch
NEC
NEC Univerge SV8100 R2 Installationsanleitung
NEC
NEC TM1200 Bedienungsanleitung
NEC
NEC N8100-1793F Bedienungsanleitung
NEC
NEC NEC Express5800 Series Bedienungsanleitung
NEC
NEC N8800-103F Bedienungsanleitung
NEC
NEC Express5800/R120e-1M EXP291 Bedienungsanleitung
NEC
NEC iLO 5 Bedienungsanleitung
NEC
NEC Express5800/120Mc2 series Bedienungsanleitung
NEC
NEC Express5800/120Rj-2 Bedienungsanleitung
NEC
NEC Esmpro 320La Bedienungsanleitung
NEC
NEC Express5800/180Ra-7 Bedienungsanleitung
NEC
NEC DT330 Referenzhandbuch
NEC
NEC NECCare Gold Express5800/320Fd Handbuch
Beliebte Server Handbücher anderer Marken
Nortel
Nortel 1000 Con?guration guide Bedienungsanleitung
Asus
Asus AP7500 Bedienungs- und Wartungshandbuch
Avid Technology
Avid Technology AirSpeed 5000 Bedienungsanleitung
HP
HP Integrity rx2600 Installationsanleitung
Milestone
Milestone Husky IVO 350T Bedienungsanleitung
Planet
Planet NAS-7410 Bedienungsanleitung