NEC Express5800/140Hb Bedienungsanleitung

System Release Notes

Express5800/140Hb

System Release Notes

PN: 455-01598-002

Proprietary Notice and Liability Disclaimer

The information disclosed in this document, including all designs and related materials, is

the valuable property of NEC Computers Inc. and/or its licensors. NEC Computers Inc.

and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights

to this document, including all design, manufacturing, reproduction, use, and sales rights

thereto, except to the extent said rights are expressly granted to others.

The NEC Computers Inc. product(s) discussed in this document was warranted in

accordance with the terms of the Warranty Statement accompanying each product.

However, actual performance of each such product is dependent upon factors such as

system configuration, customer data, and operator control. Since implementation by

customers of each product may vary, the suitability of specific product configurations and

applications must be determined by the customer and is not warranted by NEC Computers

Inc.

To allow for design and specification improvements, the information in this document is

subject to change at any time, without notice. Reproduction of this document or portions

thereof without prior written approval of NEC Computers Inc. is prohibited.

Trademarks

Windows 2000 and Windows NT are registered trademarks of Microsoft Corporation.

Novell and NetWare are registered trademarks of Novell, Inc.

SCO OpenServer is a trademark of The Santa Cruz Operation, Inc.

UnixWare is a registered trademark of The Santa Cruz Operation, Inc.

All other product, brand, or trade names used in this publication are the trademarks or registered trademarks

of their respective trademark owners.

April 2001

NEC Computers Inc.

15 Business Park Way

Sacramento, CA 95826

Express5800/140Hb

System Release Notes

The Express5800/140Hb System Release Notes provide up-to-date information

on your system. These notes also provide additional valuable information about

your system that was not included in the user’s guide.

Please read these notes in their entirety.

CONTENTS

Introduction ............................................................................................................................................3

General Comments .................................................................................................................................3

Advisories...............................................................................................................................................3

EXPRESSBUILDER .........................................................................................................................3

SCO....................................................................................................................................................4

System Hardware ...............................................................................................................................4

Documentation Errata.............................................................................................................................5

nec

Express5800/140Hb System Release Notes 3

Introduction

These System Release Notes cover the following topics:

!General Comments

!Advisories

!Documentation Errata.

General Comments

The following general comments apply to this server.

!Versions of the Network Operating Systems tested and recommended are:

Windows®2000

Windows NT®4.0 Server with Service Pack 6

Novell® NetWare®5.1

SCO OpenServer™5.05 with Maintenance Supplement 505A.

UNIXWare®7.1.1

Advisories

This section contains advisories on the EXPRESSBUILDER, SCO, and system

hardware.

EXPRESSBUILDER

The following advisory applies to EXPRESSBUILDER.

!EXPRESSBUILDER EasySetup always configures the Windows 2000

TCP/IP Protocol IP settings to "Obtain an IP address automatically"

(DHCP), regardless of the IP address setting specified in EasySetup. If static

TCP/IP addressing is required, TCP/IP must be reconfigured. Refer to

Windows documentation for instructions.

!After installing Windows 2000, the Windows 2000 Device Manager may

show an NEC GEM SCSI Processor Device and/or an Unknown Device

under Other Devices. The Unknown Device is a reference to the baseboard

management controller. Installing the ESMPRO Agent can clear both of

these conditions.

!If you already have an operating system installed when creating a

maintenance partition, EXPRESSBUILDER will warn you of the existing

partition. If you want to preserve the installed operating system, do not

create the maintenance partition or the existing operating system will be

overlaid by the maintenance partition.

4Express5800/140Hb System Release Notes

!The Administrator Menu in the System Information Management segment

of the Offline Maintenance Utility is accessible only by NEC authorized

service representatives.

!EXPRESSBUILDER operates in floppy emulation mode. The emulated

floppy drive portion of your system CD-ROM is designated Drive A and the

remaining portion(s) of the CD-ROM is designated Drive Q. Your system

diskette drive is Drive B. After creating the Off-line Maintenance Utility

diskette, EXPRESSBUILDER prompts you to remove the diskette from

Drive B. At this prompt, remove the diskette from your diskette drive.

SCO

The following advisory applies when using SCO 5.05.

During the installation of SCO or any time thereafter when booting SCO

a warning message may appear as follows:

WARNING: Cannot connect to APM, error 0x0036 System loaded, press <Return> to

start:

To prevent the WARNING message from appearing, boot the system to

single-user Mode. Edit the /etc/default/boot file. Add "apm.check=no" to

the end of the line indicated by the "DEFBOOTSTR=" entry.

System Hardware

The following advisory applies to the Plug and Play feature of your server's I/O

expansion boards.

The factory standard default value (Hot-Plug PCI Master Control) of the

Plug N Play feature in your server is enabled. The Windows 2000

operating system requires that the Hot-Plug PCI Master Control feature

be enabled. To disable it, if required by your operating system, the Hot-

Plug PCI Master Control feature in the Advanced Submenu of the BIOS

Setup Utility described in Chapter 3 "BIOS Setup Configuration Settings"

can be changed to "disabled."

The following advisory applies to your system's documentation.

Both the User's Guide and Service Guide refer to the two SCSI channels

as either channel A and channel B or as channel 0 and channel 1. The

terms channel A and channel B are used when referencing the SCSI

channels from the on-board SCSI controller. The terms channel 0 and

channel 1 are used when referencing the SCSI channels from a RAID

controller. Therefore, it should be noted that these terms are an exact

counterpart of each other and can be used interchangeability.

Express5800/140Hb System Release Notes 5

Documentation Errata

The following changes apply to the Express5800/140Hb User's Guide

(456-01546-000) located on the EXPRESSBUILDER CD-ROM:

!Chapter 3, Configuring System Board Jumpers.

Replace Figure 3-2 System Jumpers with the following figure.

AProcessor speed jumper block

(located in the CPU cage)

DBattery power control/reset jumper block

BSystem function jumper block ESystem board

CDump/reset jumper block

Figure 3-2. System Jumpers

Replace Table 3-4 Processor Speed Jumper Summary with the

following table.

Table 3-4. Processor Speed Jumper Summary

Jumper SettingsProcessor

Frequency

(MHz) 1-2 3-4 5-6 6-8

700 ON OFF OFF ON

800 ON OFF ON OFF

900

(Fixed Bus Ratio)

N/A N/A N/A N/A

6Express5800/140Hb System Release Notes

Andere Handbücher für Express5800/140Hb

Inhaltsverzeichnis

Andere NEC Server Handbücher

NEC

NEC UNIVERGE NEAX 2000 IPS Bedienungsanleitung

NEC

NEC NEC Express5800 Series Bedienungsanleitung

NEC

NEC Univerge SV8100 Bedienungsanleitung

NEC

NEC Express5800/320Lb FT Linux Bedienungsanleitung

NEC

NEC Express 5800 TM700 Bedienungsanleitung

NEC

NEC NEAX 2000IVS2 Bedienungsanleitung

NEC

NEC Express5800/180Rb-7 Bedienungsanleitung

NEC

NEC Univerge SV8100 Bedienungsanleitung

NEC

NEC Express5800/R320g-M4 Betriebsanleitung

NEC

NEC Express5800/R120g Betriebsanleitung

NEC

NEC N8100- 1241F Bedienungsanleitung

NEC

NEC EXPRESS5800/R320d-E4 Bedienungsanleitung

NEC

NEC ExpEther-2S Bedienungsanleitung

NEC

NEC Univerge SV9100 Bedienungsanleitung

NEC

NEC NEAX 2000 IVS Benutzerhandbuch

NEC

NEC Express5800/R120f-1E Bedienungsanleitung

NEC

NEC Express5800/T120e Bedienungsanleitung

NEC

NEC Express 5800 Bedienungsanleitung

NEC

NEC Express5800 120Ed Referenzhandbuch

NEC

NEC Express 5800/320Lb-R Bedienungsanleitung

NEC

NEC N8100-1447F Bedienungsanleitung

NEC

NEC NEAX 2000 Bedienungsanleitung

NEC

NEC NEAX2000 IVS2 Bedienungs- und Wartungsanleitung

NEC

NEC Express5800/120Rh-1 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung