NEC NEC Express5800 Series Montageanleitung

NEC Express5800 Series

Note: Microsoft and Windows are registered trademarks of Microsoft Corporation in the U.S. and

other countries.

t®

r™

™

t®

r™

™

NEC Express5800/120Lh Operation Manual for Microsoft®Windows Server™ 2003 x64 Editions

™

This manual explains how to install the Microsoft® Windows Server™ 2003, Standard x64

Edition/Microsoft® Windows Server™ 2003, Enterprise x64 Edition (called the "Windows

Server 2003 x64 Editions" hereinafter) by using an NEC difference module for the Windows

Server 2003 x64 Edition for Express5800/120Lh.

Before installing the Windows Server 2003 x64 Editions, be sure to read this manual

thoroughly.

NOTE

The NEC difference module for the Windows Server 2003 x64 Edition

for Express5800/120Lh is dedicated to the Express5800/120Lh. This

module cannot be used for other devices.

The installation procedure of the Windows Server 2003 x64 Editions is outlined below.

It is impossible to upgrade the Windows Server 2003 x64 Editions from an existing 32-bit

edition.

These editions must be newly installed.

Preface

Installation Procedure Outline of the Windows Server

2003 x64 Editions

Create Windows Server 2003 x64 Edition OEM-DISK for EXPRESSBUIDLER

Update BIOS and perform BIOS Setup

Install Windows Server 2003 x64 Editions

System update

Setup for failure handling

Set driver details

NEC Express5800/120Lh Operation Manual for Microsoft®Windows Server™ 2003 x64 Editions





Items Required for Installation

Before starting to install the Windows Server 2003 x64 Editions, check that the

following media and manuals have been prepared:

NEC difference module for the Windows Server 2003 x64 Edition for the

Express5800/120Lh

(Called the NEC difference module hereinafter)

Visit NEC Express5800 Web Site (http://www.nec.co.jp/express/) (this Website

is called the download site hereinafter), and acquire the module.

Windows Server 2003 x64 Edition OEM-DISK for EXPRESSBUILDER

(or one 3.5-inch floppy disk in the 1.44MB format)

For the creation procedure, see "Creating the Windows Server 2003 x64 Edition

OEM-DISK for EXPRESSBUILDER".

NEC Express5800/120Lh Operation manual For Microsoft® Windows

Server™ 2003, Standard x64 Edition/Microsoft® Windows Server™ 2003,

Enterprise x64 Edition

Microsoft® Windows Server™ 2003, Standard x64 Edition/

Microsoft® Windows Server™ 2003, Enterprise x64 Edition

(CD-ROM) * To be purchased separately.

(Called the Windows Server 2003 x64 Edition CD-ROM hereinafter)

or Backup CD-ROM Microsoft Windows Server 2003, Standard x64

Edition/Backup CD-ROM Microsoft Windows Server 2003, Enterprise x64

Edition (called the backup CD-ROM hereinafter)

The following are supplied when the Express5800 series is purchased:

- EXPRESSBUILDER CD-ROM

- User's Guide

(See "Online Document" from the master control menu of the

EXPRESSBUILDER CD-ROM.)





Downloading the NEC Difference Module

Before creating the Windows Server 2003 x64 Edition OEM-DISK for

EXPRESSBUILDER or updating the system, download the NEC difference module

for the Express5800/120Lh by following the steps below.

(1) Visit the Download site and download the NEC difference module for the

Express5800/120Lh.

(2) After downloading the module, store it in any folder on the hard disk.

(Example: C:¥TEMP)

NOTE

Any folder name including blank characters cannot be

specified as the name of the download destination folder.

Preparation for Installing the Windows Server 2003 x64 Editions

NEC Express5800/120Lh Operation Manual for Microsoft®Windows Server™ 2003 x64 Editions







Creating the Windows Server 2003 x64 Edition OEM-DISK for

EXPRESSBUILDER

The installation requires a floppy disk called the Windows Server 2003 x64 Edition

OEM-DISK for EXPRESSBUILDER. Follow the creation steps below.

TIPS

When the Windows Server 2003 x64 Edition OEM-DISK for

EXPRESSBUILDER has already been created for the

device, it is unnecessary to create a new one.

Follow the steps below to create the disk:

(1) Prepare one empty 3.5-inch floppy disk formatted to the 1.44MB format.

(2) Start the operating system.

(3) Download the NEC difference module.

(See "Downloading the NEC Difference Module".)

(4) Set the floppy disk in the floppy disk drive.

(5) Copy all files in the following folder to the floppy disk:

<storage-destination-folder-name>¥WINNT¥OEMFD¥W2K3AMD¥FD1

Completion of the copy operation completes the creation of the Windows

Server 2003 x64 Edition OEM-DISK for EXPRESSBUILDER.

Write-protect the created Windows Server 2003 x64 Edition OEM-DISK for

EXPRESSBUILDER, attach a label to the floppy disk, and keep it in a safe place.

NEC Express5800/120Lh Operation Manual for Microsoft®Windows Server™ 2003 x64 Editions

Before installing Windows Server 2003 x64 Editions, read the following precautions

carefully.





Procedure for Obtaining a License

When the backup CD-ROM is used, its content is installed in the licensed state. When

other OS CD-ROMs are used, a procedure for obtaining the license of the Windows

Server 2003 x64 Editions is required. The product key used in the procedure and the

product key indicated on the COA label provided with the Windows Server 2003 x64

Editions must match.

IMPORTANT

•Perform activation within 30 days after the installation.

After 30 days elapse, the system may be locked.

•The COA label may be adhered to the device.





Optional Boards Supported by the NEC Difference Module

The following optional boards are supported by the NEC difference module:

•Boards for which OS installation is supported by the NEC difference module

- N8103-80F disk array controller (1ch)

- N8103-81F disk array controller (2ch)

- SCSI HostRAID (the controller on the motherboard is used)





Disk Configuration

The disk area may contain an area labeled "EISA configuration". This area is a

maintenance partition for storing configuration information and utilities. So, this area

must not be deleted.

Precautions

NEC Express5800/120Lh Operation Manual for Microsoft®Windows Server™ 2003 x64 Editions





Re-

Installation on a Dynamic Disk

When the hard disk drive that has been upgraded to a dynamic disk is used for

re-installation, if there is a partition other than the partition in which the OS is installed,

and you want to keep that partition, note the following:

•As the partition where the OS is to be installed, select the partition where the OS

was installed before.

•For the OS partition format, select "Use the current File System".





Magneto-optical drive

When NTFS is set for the file system with a magneto-optical drive left connected at the

time of installation, file system conversion may not be performed correctly.

If correct file system conversion is not performed, remove the magneto-optical drive, and

perform the installation from the beginning.





DAT and Other Media

During setup, do not set any media such as a DAT that are not required for installation.





Updating BIOS

Before the Windows Server 2003 x64 Editions can be installed, BIOS for the Windows

Server 2003 x64 Editions may have to be updated by using the EXPRESSBUILDER

CD-ROM.

To determine whether BIOS update is required or not, visit the download site and check

for any supported module.

For the update procedure, see the introductory statements presented at the time of BIOS

downloading to each device and "Readme.txt" included in downloaded data.

NEC Express5800/120Lh Operation Manual for Microsoft®Windows Server™ 2003 x64 Editions





Size of a Created Partition

The size of a partition where the system is installed can be calculated from the following

expression:

Required size for installation + paging file size + dump file size + application size

Required size for installation =

4100MB

Paging file size (recommended) = Installed memory size ×1.5

Dump file size = Installed memory size + 1MB

Application size = Any size

IMPORTANT

•The above paging file size is a recommended size for collecting

debug information (dump file). The boot volume requires a

paging file having an enough initial size for storing the dump file.

If the paging file becomes insufficient, collection of accurate

debug information may fail because of virtual memory shortage.

Therefore, set a sufficient paging file size for the entire system.

•If the installed memory size is 2GB or more, the maximum

dump file size is 2048MB plus 1MB.

•When other applications are to be installed, add the disk space

required for these applications to the partition size.

When the installed memory size is 512MB, for example, the partition size is calculated

using the above expression as follows:

4100MB + (512MB ×1.5) + 512MB + 1MB + application size

= 5381MB + application size

If the partition where the system is installed is smaller than the size (the required size for

installation plus the paging file size), enlarge the partition size, or install an additional

disk. If the dump file size cannot be allotted, more than one disk can be assigned as

follows:

(1) Set the size (the required size for installation plus the paging file size).

(2) See "Setup for Failure Handling" and make settings so that debug

information (for the dump file size) is written to another disk.

If the disk does not have enough space for writing for the dump file size, install the system

with the partition size set to the required size for installation plus the paging file size, and add

a new disk.





Manual Installation

The [Install hardware/install software] pop-up window may appear twice during

installation, which does not affect the system operation, however. Click [Yes] each time

and continue the installation steps.

In the subsequent steps, follow the messages to continue the installation.

NEC Express5800/120Lh Operation Manual for Microsoft®Windows Server™ 2003 x64 Editions





Creating a RAID Drive

When SCSI HostRAID is to be used, set HostRAID to Enabled with the SCSI Select

Utility to create a RAID drive before installation. For how to create a RAID drive, refer

to the description of RAID configuration in the user's guide. When using an optional

disk array controller, refer to the manual supplied with the board.

NEC Express5800/120Lh Operation Manual for Microsoft®Windows Server™ 2003 x64 Editions

This chapter explains how to newly install the Windows Server 2003 x64 Editions.

1. Turn on the power to the system.

IMPORTANT

Update BIOS for the Windows Server 2003 x64 Editions if necessary.

To determine whether BIOS update is required or not, visit the download

site and check for any supported module.

A description of POST (Power On Self-Test) is displayed on the display screen.

(If the "NEC" logo is displayed, press the <Esc> key.)

In a little while, the following message appears in the lower left part of the screen:

Press <F2> to enter SETUP

2. Press the <F2> key, select "Advanced" from the BIOS Setup menu, and set "Installed

O/S" to "PnP O/S". The setting method varies from model to model. For details,

refer to "Readme.txt" included in the BIOS download data of the device.

3. From the BIOS Setup menu, select "Exit" →"Save Changes & Exit", and select [Yes]

to restart the system.

4. Set the Windows Server 2003 x64 Edition CD-ROM or backup CD-ROM in the

CD-ROM drive, then perform a reset operation (by pressing the <Ctrl>+<Alt>+<Del>

keys) or turn the power off then on again to restart the NEC Express5800 series.

IMPORTANT

When an OS that is ready for operation is already installed on the hard

disk, press the <Enter> key while "Press any key to boot from CD..." is

displayed on the screen. This operation is unnecessary if there is no

OS that is ready for operation.

The system starts from the CD-ROM, starting the installation program.

The Windows Server 2003 x64 Editions setup screen appears. If the screen does

not appear, the <Enter> key was not pressed correctly. Turn on the power to the

system again, and start the steps from the beginning.

1 Installing Windows Server 2003 x64 Editions

NEC Express5800/120Lh Operation Manual for Microsoft®Windows Server™ 2003 x64 Editions

5. Press the <F6> key while "Setup is inspecting your computer's hardware

configuration.." is displayed in the upper part of the screen.

TIPS

•Pressing the <F6> key does not change the screen display.

•When SATA HostRAID or SCSI HostRAID is used, a RAID drive must be

created in advance. Refer to the description of RAID configuration in

the user's guide.

•When an optional disk array controller is used, refer to the manual

supplied with the board.

When the <F6> key need not be pressed, the subsequent steps are unnecessary.

Perform setup operation according to the instructions displayed on the screen. For

details, refer to "First Step Guide".

6. When the following message is displayed, press the <S> key:

The following message is displayed:

7. Set the Windows Server 2003 x64 Edition OEM-DISK for EXPRESSBUILDER in the

floppy disk drive, and press the <Enter> key.

A list of SCSI adapters is displayed.

Please insert the disk labeled

Manufacturer-supplied hardware support disk

into Drive A:

* Press ENTER when ready.

Setup could not determine the type of one or more mass storage

devices installed in your system, or you have chosen to

manually specify an adapter. Currently, Setup will load

support for the following mass storage device(s).

Andere Handbücher für NEC Express5800 Series

107

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NEC Server Handbücher

NEC

NEC Univerge SV8100 Benutzerhandbuch

NEC

NEC NEC Express5800 Series Bedienungsanleitung

NEC

NEC SX-Aurora TSUBASA A300-2 Bedienungsanleitung

NEC

NEC NEC Express5800 Series Bedienungsanleitung

NEC

NEC TM1200 Bedienungsanleitung

NEC

NEC Active Upgrade Express5800/320Fc Technisches Handbuch

NEC

NEC NEC Express5800 Series Bedienungsanleitung

NEC

NEC NEC Express5800 Series Bedienungsanleitung

NEC

NEC Express5800/R120e-2E Bedienungsanleitung

NEC

NEC Express5800/120Rh-1 Bedienungsanleitung

NEC

NEC US110 Bedienungsanleitung

NEC

NEC R120d-2E Bedienungsanleitung

NEC

NEC Express5800/120Rg-2 Bedienungsanleitung

NEC

NEC NEC Express5800 Series Bedienungsanleitung

NEC

NEC Express5800/320Fd-LR Bedienungsanleitung

NEC

NEC Express 5800/320Lb Montage- und Bedienungsanleitung

NEC

NEC Express5800 120Li Bedienungsanleitung

NEC

NEC Express5800/120Rc-2 Bedienungsanleitung

NEC

NEC EXPRESS5800/120Re-2 Bedienungsanleitung

NEC

NEC 120Rg-2 Bedienungsanleitung

NEC

NEC Expres5800/A2040b Bedienungsanleitung

NEC

NEC Express5800/A1080a Bedienungsanleitung

NEC

NEC Express5800/320Ma Bedienungsanleitung

NEC

NEC R320c-E4 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung