NETGEAR Wg111v2 - Usb Wifi Card Includes Driver Cd Handbuch

v3.0, January 2007

Basic Setup

The NETGEAR 54 Mbps Wireless USB2.0 Adapter WG111v2 lets you connect a PC computer to

wireless networks. It is designed for PC computers running Microsoft Windows. For information

about product features and compatible NETGEAR products, please see the NETGEAR website at

http://www.netgear.com.

This chapter describes how to install your wireless USB adapter and set up basic wireless

connectivity on your Wireless Local Area Network (WLAN). Advanced wireless network set up is

covered in “Network Connections and Wireless Security” on page 11.

What You Need Before You Begin

You must verify that your computer meets the minimum system requirements and identify the

wireless network settings of the wireless network where you will connect before you can set up

your wireless USB adapter and connect.

Verify System Requirements

Before installing the Wireless Adapter, make sure that these minimum requirements have been

met. You must have a computer with:

• A Pentium300 MHz or higher compatible processor with an available USB port.

•ACDdrive.

• 10 MB of free hard disk space.

• Windows 2000, XP, or Vista.

Observe Wireless Location and Range Guidelines

Computers can connect over wireless networks indoors at a range which vary significantly based

on the location of the computer with the Wireless Adapter. For best results, avoid potential sources

of interference, such as:

• Large metal surfaces

• Microwave ovens

• 2.4 GHz Cordless phones

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual

v3.0, January 2007

In general, wireless devices can communicate through walls. However, if the walls are constructed

with concrete, or have metal, or metal mesh, the effective range will decrease if such materials are

between the devices.

What Is in the Box

The product package should contain the following items:

• NETGEAR 54 Mbps Wireless USB2.0 Adapter WG111v2

• Installation Guide

• Plastic cradle and fasteners to hold the WG111v2

•NETGEAR CD, including:

– Driver and Configuration Utility Software

– This User Manual

• Warranty and Support information card

If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the

carton, including the original packing materials, in case you need to return the product.

Default Wireless Settings

If this is a new wireless network installation, use the factory default settings to set up the network

and verify wireless connectivity. If this is an addition to an existing wireless network, you need the

wireless network and wireless security settings that are already defined.

Your Wireless Adapter factory default basic settings are:

• Network Name Service Set Identification (SSID): ANY

• Network Mode (Infrastructure or Ad-hoc): Infrastructure

• Data security WEP, WPA2-PSK, or WPA-PSK encryption: Disabled

The section below provides instructions for setting up the Wireless Adapter for basic wireless

connectivity to an access point.

Note: In order for the Wireless Adapter to communicate with a wireless access point

or wireless adapter, all devices must be set up to use the same wireless network

name (SSID).

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual

v3.0, January 2007

Installation Instructions

The instructions in this chapter are for an Access Point (Infrastructure) installation. Wireless

security, advanced settings, and Computer-to-Computer (Ad Hoc) instructions are covered in

“Network Connections and Wireless Security” on page 11.

Follow the instructions below to install the Wireless Adapter.

1. First, install the software. Insert the NETGEAR CD. If the CD main page does not appear,

double click Autorun.exe on the CD.

a. Click Install the Software.The Check for Updates window will open.

b. If you are connected to the Internet, click Check for Updates. If not, you can choose to

install from the CD.

c. When the Installation Complete message appears, click Next.

d. On the Smart Wizard screen, click Next to proceed with the Smart Wizard setup.

2. Now, when prompted, insert your wireless USB adapter.

a. Click Next to proceed. Windows will discover the adapter and continue the software

installation process.

Figure 1

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual

v3.0, January 2007

b. Follow the Windows prompts to complete the software installation.

c. If a Windows logo certification warning appears, click Continue to proceed with the

installation.

d. When the Windows software installation is complete, click Finish.

3. Windows 2000 users go to Step 4. Windows XP or Vista users can set up the wireless adapter

either with the NETGEAR Smart Wizard (recommended) or the Windows Configuration

Utilities.

•NETGEAR Smart Wizard: Reveals more information about each network and makes it

easier to troubleshoot network connection problems. See “The Smart Wizard Status Bar”

on page 7 and “Statistics Page” on page 26.

•Windows Zero Configuration Utility: See the Windows documentation or see the link to

“Windows XP and Vista Wireless Configuration Utilities” on page 35.

Figure 2

Figure 3

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual

v3.0, January 2007

4. Use the Smart Wizard to set up your Wireless Adapter

a. When prompted, click Next to let the wizard help you connect to a network

(recommended).

b. Select the wireless network from the drop-down list, and the wizard records your choice.

If the network uses security, then the Smart Wizard detects it..

c. Follow the Wizard steps for Security (if used) and for saving a Profile.

d. After you have reviewed the settings, click Finish.

Figure 4

Note: Hidden networks do not broadcast the Network Name (SSID). These

networks are in the drop-down list, but the Network Name (SSID) is blank

Figure 5

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual

v3.0, January 2007

The icon appears in the System Tray and on the desktop. The wizard initiates your

wireless connection. It could take up to a minute for your wireless connection to be

established.

The Smart Wizard Settings page opens.

5. Use the status bar to verify your wireless connectivity. For more information about

connecting, see “Connecting to Wireless Networks and the Internet” on page 6.

Connecting to Wireless Networks and the Internet

The Wireless Adapter has indicators that show the status of your connection to a wireless network

and to the Internet:

• Icon: After you install the software, this icon appears on the desktop and in the lower

right of the Windows task bar. It is color coded to show the status of the connection. See “The

Smart Wizard Status Bar” on page 7.

•Smart Wizard Status Bar: Clicking on the system tray icon opens the Smart Wizard. The

status bar at the bottom of the page shows details about your wireless and Internet connection.

Figure 6

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual

v3.0, January 2007

The Smart Wizard Status Bar

Click the icon to open the Smart Wizard so you can view the status bar. The Smart Wizard

Settings page opens. The status bar is at the bottom of the page.

•Connection Status: The color shows the connection status.

•Signal Strength: Shows the signal strength of the wireless network. If the signal is poor, then

try moving closer to the wireless access point.

•Lock icon: Shows if security is used on the network.

•Router/Internet connection indicator: This shows the progress of your connection. By

default, this feature is on.

If you selected Europe during the WG111v2 installation, this feature is disabled.

The Router/Internet connection indicator is useful in isolating a problem. For example, if you are

connected to a router, but not to the Internet, then check the router’s Internet connection.

If you right-click the System Tray icon, you can disable the Internet notification feature by

clearing the check mark on this line. If you do so, then only the IP address is shown.

Figure 7

Figure 8

Connection Indicator Description

Connected to Internet

or IP Address Wireless Internet connection OK.

Connected to Router Wireless connection to router OK but no Internet

connection at router.

___.___.___.___ or

169.254..x.x Wireless connection to a router OK but there is a

problem with the router. See “Troubleshooting”.

signal strength

Unlocked: Network does not use security

Locked: Network uses security

Router/Internet

connection

connection indicator

status

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual

v3.0, January 2007

If you selected Europe during the WG111v2 installation, you will not see the “Enable Internet

Connected Notification” option.

Icon Colors

The icon is on the desktop and in the Windows System Tray. The System Tray resides on one end

of the taskbar in the Microsoft Windows desktop.

Placing the USB Adapter Cradle

You can attach the Wireless Adapter directly to a USB port on your computer, or use the USB

cable to extend the range and obtain better wireless reception.

Follow these instructions to use the USB cable, plastic cradle, and loop and hook fastener provided

in the package for better USB Adapter placement on a notebook computer:

1. The Wireless Adapter comes with three black fasteners. Locate the one that has a prickly side

and attach it to the plastic cradle on the middle of the outside rear.

2. Insert the Wireless Adapter in the plastic cradle.

Figure 9

Color Condition Description

Red The wireless USB adapter

has no connection to any

other wireless node.

The Wireless Adapter can not link to any other wireless node

or the link is lost. Check your configuration or try moving to a

location where the wireless signal quality is better.

Yellow The wireless USB adapter

has a connection with another

wireless node.

The wireless link is weak. You may need to move to a better

spot, such as closer to the wireless access point. Also, look

for possible interference such as a 2.4 GHz cordless phone or

large metal surface.

Green The wireless USB adapter

has a connection with another

wireless node.

The wireless USB adapter has established good

communication with an access point and the signal quality is

strong.

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual

v3.0, January 2007

3. Place one of the other pieces of loop and hook fastener on the back of the monitor near the top

for better reception.

4. Join the pieces of the fastener to attach the USB Adapter in the plastic cradle to the notebook

or desktop monitor.

See the installation instructions for your operating system before attaching the USB cable to the

USB Adapter and your computer

Removing the Software

You can remove the Wireless Adapter software in these two ways:

• Navigate the Windows Start menu to the NETGEAR 54 Mbps Wireless USB2.0 Adapter

WG111v2 program group, select the uninstall option, and follow the screen prompts.

• Navigate the Windows Start menu to the Control Panel Add or Remove Program item, select

the NETGEAR 54 Mbps Wireless USB2.0 Adapter WG111v2 option, and follow the screen

prompts.

Tip: Place the last piece of fastener on the side of monitor nearest your wireless

access point.

Figure 10

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual

v3.0, January 2007

Upgrading the Wireless Adapter Software

Upgrades may be available at the NETGEAR website. To install an upgrade, follow these steps.

1. Go to http://kbserver.netgear.com

2. Click the latest version of upgrade.

3. Examine the Release Note. Make sure to read any warnings and Known Problems.

4. Download the upgrade using the link in the Release Note.

5. Follow the Release Note installation instructions.

Andere Handbücher für Wg111v2 - Usb Wifi Card Includes Driver Cd

Inhaltsverzeichnis

Andere NETGEAR Adapter Handbücher

NETGEAR

NETGEAR GA311 - Gigabit PCI Adapter Bedienungsanleitung

NETGEAR

NETGEAR Powerline 500 Bedienungsanleitung

NETGEAR

NETGEAR WNDA3200 Bedienungsanleitung

NETGEAR

NETGEAR XAV1301v1/XAVB1301v1 Leitfaden

NETGEAR

NETGEAR XAV2001 - Powerline AV Ethernet Adapter Bedienungsanleitung

NETGEAR

NETGEAR Powerline 1200 Bedienungsanleitung

NETGEAR

NETGEAR Powerline 500 Nano Bedienungsanleitung

NETGEAR

NETGEAR XAVB5501 Bedienungsanleitung

NETGEAR

NETGEAR WG111T - 108 Mbps Wireless USB 2.0 Adapter Bedienungsanleitung

NETGEAR

NETGEAR A6150 Bedienungsanleitung

NETGEAR

NETGEAR XAV6501 Bedienungsanleitung

NETGEAR

NETGEAR XAVB1501 Bedienungsanleitung

NETGEAR

NETGEAR PowerLINE 1010 Series Bedienungsanleitung

NETGEAR

NETGEAR XA601 - Powerline USB Adapter Bedienungsanleitung

NETGEAR

NETGEAR XE602 - Powerline Ethernet Adapter Bedienungsanleitung

NETGEAR

NETGEAR WN121T - RangeMax Next Wireless-N USB 2.0... Bedienungsanleitung

NETGEAR

NETGEAR XAVB5201 Bedienungsanleitung

NETGEAR

NETGEAR HDX101 - Powerline HD EN Adapter Bridge Bedienungsanleitung

NETGEAR

NETGEAR XAVB1401 Bedienungsanleitung

NETGEAR

NETGEAR PowerLine 85Mbps Bedienungsanleitung

NETGEAR

NETGEAR XAV5004 - POWERLINE AV 500 ADAPTER Bedienungsanleitung

NETGEAR

NETGEAR XAV2101 - POWERLINE AV 200 NANO ADAPTER Bedienungsanleitung

NETGEAR

NETGEAR XAVB5501 Bedienungsanleitung

NETGEAR

NETGEAR WPNT121 - RangeMax 240 USB 2.0 Adapter Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung

RCA

RCA AH57R Bedienungsanleitung

Koolatron

Koolatron AC16 Bedienungsanleitung