NETGEAR DM602 - ADSL-Modem - 8 Mbps DSL Modem Bedienungsanleitung

with Ethernet or USB connection DM602

ADSL Modem

Installation Guide

Technical Support

Please refer to the Support Information card that shipped with your product.

By registering your product at www.NETGEAR.com/register, we can provide you with faster

expert technical support and timely notices of product and software upgrades.

NETGEAR, INC.

Support Information

Phone: 1-888-NETGEAR (For US & Canada only)

For other countries see your Support Information card.

E-mail: Support@NETGEAR.com

Website: www.NETGEAR.com

NETGEAR and Auto Uplink are trademarks or registered trademarks of NETGEAR, Inc. in the United States and/or

other countries.

Other brand and product names are trademarks or registered trademarks of their respective holders.

Information is subject to change without notice.

Introduction

Thank you for purchasing a NETGEAR DM602 ADSL Modem. With this modem you can

have secure high-speed ADSL Internet access for your computer using either an Ethernet or

USB cable.

This installation guide shows you how to connect the modem and configure it for secure

Internet access. Setup is easy—follow the instructions in this guide and your system will be up

and running quickly.

If you have problems, there is a troubleshooting section on pages 11 and 12 to help you. You

can get more detailed troubleshooting information from the Reference Manual on the CD,

online at www.NETGEAR.com, or by phone. If you have questions about terminology, you

can find definitions in the short glossary on page 13 and in the more extensive glossary in the

Reference Manual.

On the DM602 Resource CD, you’ll find the DM602 Installation Assistant, which supplements

the instructions in this installation guide by animating the step-by-step procedures given here.

For more detailed information about installation, troubleshooting and configuration

procedures, see the Reference Manual on the CD.

Installation Overview

Estimated time: 15 to 30 minutes

1. Gather the configuration information you have for your Internet account from your

Internet Service Provider (ISP).

2. Connect the modem to your computer.

3. Configure your computer to work with the modem and restart the computer.

4. Configure the modem and go online to test the connection.

ADSL Modem DM602

What’s in the Box

When you open the box, verify that you received everything.

The package includes:

•DM602 ADSL Modem

•AC power adapter

•Microfilter splitter (depending on the country of purchase)

•Category 5 Ethernet straight-through cable

•USB cable (depending on the country of purchase)

•Phone cable

•DM602 Resource CD, including a full Reference Manual and Installation Assistant

•DM602 Installation Guide (this document)

•Warranty and registration card

•Support information card

DM602 ADSL Modem

Resource CD, installation guide,

support information card &

warranty/registration card

Power adapter

Category 5

100 Mbps

Ethernet cable

Phone Cable

Micro Filter

DSL FILTER

DSL

HPN PHONE

LINE

ADSL Modem DM602

Gather Configuration Information from

Your Internet Service Provider

Before installing the DM602 modem, you must have active ADSL service and an Internet account

with an Internet Service Provider (ISP).

Ethernet Connection

You may use the Ethernet connection with any computer that supports TCP/IP. To connect the

modem with an Ethernet cable, you must have the following:

•An available RJ-45 Ethernet port in the computer —either built-in or on an installed

network interface card (NIC).

Note: If you have a built-in modem or a modem card, the telephone jack for the

modem looks very similar to an RJ-45 Ethernet port, but the RJ-45 port is larger.

•TCP/IP networking installed.

•For Windows®computers: Client for Microsoft®Networks software installed.

Note: TCP/IP and Client for Microsoft Networks is installed on most Windows

computers. If you have viewed Web sites with a browser, you are ready to go.

Please see the Reference Manual on the CD if you need help installing either on a

Windows computer.

•An Ethernet patch cable. (One is provided with the modem.)

USB Connection

You may use the USB connection with any Windows computer that has an available USB port.

To connect the modem with a USB cable, you must have the following:

•A computer running Windows 98 or later.

•An available USB port.

•A USB cable.

Connection information

Later in the setup process when you configure the modem to work with your computer, you’ll

need to know the type of account you have with your ISP and specific account information.

The next page includes blanks for you to fill in your ISP information and use later.

Note: Your ISP should have provided you with a summary sheet of all the

information needed to connect your computer to the Internet. If you cannot locate

the information, you’ll have to contact your ISP. 3

Multiplexing Method and Virtual Circuit Number

Your ISP should give you information about the type of multiplexing used and the numbers for

the virtual circuits, if used.

Circle either:

VC-Based or LLC-Based

Note: Use LLC-Based if your ISP did not give you a specific method.

VPI: (a number between 0 and 255)

VCI: (a number between 1 and 65535)

If your ISP requires a login name and password because you have a PPPoE or PPPoA account,

fill in the following:

Password:

Service name: (if required by your ISP)

Note: The login name could be called a user name or account name by your ISP.

The login name is case sensitive. You must type it exactly as given by your ISP. For

example, c_jones is a different login name than C_Jones or cjones.

Fixed (or Static) IP Address

If you have a static IP address through your ISP, fill in the following information:

Internet IP address:

Subnet mask:

Gateway IP address:

DNS server address information

If you were given specific Domain Name System (DNS) server addresses, fill in the following:

DNS Server IP address(es):

...

Note: For example,

169.254.141.148 could

be a valid IP address.

...

Connect the Modem

After unpacking the box and locating the configuration

information, you can install the modem.

Note: You do not have to power down your

computer to do this, but if you need to move your

computer (perhaps to get to a port in the back),

you may want to shut down the computer before

moving it.

Ethernet Connection

1. Connect a phone cord between the telephone wall

jack and the ADSL port on the modem.

Note: If you want to connect a telephone using this wall jack, you may use a

microfilter splitter as illustrated.

2. Use an Ethernet cable to connect the computer to the Ethernet port on the modem.

Note: If you’ve powered down your computer, start it up now.

3. Connect the power adapter into the back of the modem and then plug the adapter into a

power source (such as a wall socket or power strip) and make sure that power is applied.

4. Check the setup. (See the procedure on the next page.)

USB Connection

To use the USB port on the modem you must have a computer with Windows 98 or later.

1. Connect a phone cord between the telephone wall jack and the ADSL port on the

modem.

Note: If you want to connect a telephone at the wall jack, you may use a microfilter

splitter as illustrated.

2. Connect the power adapter into the back of the modem and then plug the adapter into a

power source (such as a wall socket or power strip) and make sure that power is applied.

Note: If you’ve powered down your computer, start it up now.

3. Insert the DM602 Resource CD in the CD-ROM drive.

4. Use a USB cable to connect the computer to the USB port on the modem.

The Add New Hardware wizard appears. 5

Phone

DSL

Line

DM602 ADSL Modem

5. Click Next to start the wizard.

6. Select Search for a suitable driver for my device and click Next.

7. Verify the driver found on the CD is dm602bus.inf and click Next.

Note: If Windows doesn’t locate the driver automatically, you have to browse for the

driver. It is in the [CD-ROM drive letter]:\DM602v1.0\USB\ folder.

8. Click Finish.

The USB driver is installed.

WARNING: Once you finish installing the USB driver, you MUST complete the

process by installing the Ethernet driver.

Next you need to install a special Ethernet driver for the modem, called NETGEAR PC-

attached Gateway, using the wizard that now appears on screen.

9. Click Next to start the wizard.

10. Again, select Search for a suitable driver for my device and click Next.

11. Verify the driver found on the CD is dm602eth.inf and click Next.

Note: If Windows doesn’t locate the driver automatically, you have to browse for the

driver. It is in the [CD-ROM drive letter]:\DM602v1.0\USB\ folder.

12. If you get queried about a Microsoft digital signature, click Yes.

13. Click Finish.

14. Check the setup.

Check the Setup

•The Power and Internet lights should be lit.

•For an Ethernet connection, the Ethernet light should be lit and may

blink to show network activity.

Note: If the Ethernet connection is a 100 Mbps connection, the light is green. If it is

a 10 Mbps connection, the light is yellow. If the Power, Internet or Ethernet light

isn’t lit, go to Troubleshooting on page 11.

•For a USB connection, the USB light should be lit and may blink

to show network activity.

Note: If the Power, Internet or USB light isn’t lit, go to Troubleshooting on page 11.

Configure the Computer to Work with

the Modem and Restart the Network

Next, you configure the computer to interact with the modem. To do this, you configure the

TCP/IP settings on the computer and then restart the computer. How you do this depends on

your computer.

Windows Operating System

Normally, you leave the TCP/IP setup parameters at their factory default settings unless you

have a specific reason to change them. You should verify that the computer is set to ‘obtain an

IP address automatically’in the Network control panel.

Windows 98 or Me

1. Choose Settings>Control Panel

from the Start menu.

2. Double-click the Network icon.

3. Click the Configuration tab.

4. In the list of installed network

components, select the TCP/IP

entry for the computer’s

Ethernet adapter or NIC.

5. Click Properties.

6. Click the IP Address tab.

7. If not selected, select Obtain an

IP address automatically.

8. Click the Gateway tab.

9. Select and remove any IP Gateway

addresses that are listed.

10. Click OK and click OK again to.

close the Network control panel.

11. Restart your computer.

Windows 98/Me

Windows 2000 or XP

1. Right-click My Network Place and

choose Properties.

2. Double-click Local Area Network

Connection and click Properties.

3. Select Internet Protocol (TCP/IP)

and click Properties.

4. Select Obtain IP address

automatically and Obtain DNS

server address automatically.

5. Click OK twice and click Close.

6. Restart your computer.

Macintosh Operating System

Mac OS® 8.6 or 9.x

1. Choose Control Panels >TCP/IP

from the Apple () menu.

2. If not already selected, select Ethernet

in the Connect via list.

3. Select Using DHCP Server in the

Configure list.

4. Click the close box.

5. Click Save.

6. Restart your computer.

Mac OS X

1. Choose System Preferences from the Apple menu.

2. Double-click Network.

3. If not already selected, select Built-in Ethernet in the Configure list.

4. If not already selected, select Using DHCP in the TCP/IP tab.

5. Click Save.

6. Restart your computer.

Linux®or UNIX®Operating System

If you’re installing the modem with a Linux-based or UNIX-based computer, see your system

documentation to set up TCP/IP networking to obtain IP addresses automatically using DHCP.

Mac OS 8.6/9.x

Andere Handbücher für DM602 - ADSL-Modem - 8 Mbps DSL Modem

Inhaltsverzeichnis

Andere NETGEAR Modem Handbücher

NETGEAR

NETGEAR DG834N Bedienungsanleitung

NETGEAR

NETGEAR CM500 Bedienungsanleitung

NETGEAR

NETGEAR DG814 - DSL Modem Internet Gateway Bedienungsanleitung

NETGEAR

NETGEAR CGD24G Bedienungsanleitung

NETGEAR

NETGEAR CM500 Bedienungsanleitung

NETGEAR

NETGEAR LM1200 Bedienungsanleitung

NETGEAR

NETGEAR XM128 Bedienungsanleitung

NETGEAR

NETGEAR A7000 Bedienungsanleitung

NETGEAR

NETGEAR 341U Bedienungsanleitung

NETGEAR

NETGEAR Nighthawk C7100V Bedienungsanleitung

NETGEAR

NETGEAR DG834PN - RangeMax ADSL Modem Wireless... Bedienungsanleitung

NETGEAR

NETGEAR AC327U Bedienungsanleitung

NETGEAR

NETGEAR Netgear DM11PSP Bedienungsanleitung

NETGEAR

NETGEAR Orbi RBS50Y Bedienungsanleitung

NETGEAR

NETGEAR AirCard Bedienungsanleitung

NETGEAR

NETGEAR CG814WG V3 Bedienungsanleitung

NETGEAR

NETGEAR CMD31T-100NAS Bedienungsanleitung

NETGEAR

NETGEAR AC329U Bedienungsanleitung

NETGEAR

NETGEAR CM500 Bedienungsanleitung

NETGEAR

NETGEAR DM602 - ADSL-Modem - 8 Mbps DSL Modem Bedienungsanleitung

NETGEAR

NETGEAR DG834GSP Bedienungsanleitung

NETGEAR

NETGEAR CGD24G Bedienungsanleitung

NETGEAR

NETGEAR CM500V Bedienungsanleitung

NETGEAR

NETGEAR CM1150V Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung