NETGEAR R9000 Bedienungsanleitung

Contents

1 Introduction• 2 Hardware Specifications• 3 Installation• 4 Upgrading/Downgrading

DD-WRT

•

5 Recovery• 6 GPIO• 7 VLAN Detached networks

7.1 Detaching the

SFP+ port

♦

•

Introduction

Hardware Specifications

See Netgear R9000 on wikidevi

This router can handle top VPN speeds, as of 2019.

Please note, Wireless-AD (60GHz) support is untested at this time, 2019.

10g interface- supported SFP hardware info:

https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1230130#1230130

Installation

Download and flash the factory-to-ddwrt.img file:

Authenticate to the router. The original Netgear firmware defaults to IP address 192.168.1.1,

username "admin" and password "password"

Go to the Administration page - then Upgrade (or something similar).2. You will see a notice about the file you uploaded being older than the firmware currently on the

router. Click Yes to proceed.

The router will flash DD-WRT. Wait a few minutes (5 min to be safe).4.

Try logging into DD-WRT at http://192.168.1.1. You should see a screen asking you to create a username and

password.

Netgear_R9000

Contents 1

Upgrading/Downgrading DD-WRT

Download and flash the r9000-webupgrade.bin file:

NOTE: The webupgrade.bin file is only used to upgrade or downgrade to a *different* version

of DD-WRT.

•

Authenticate to the router.1. Go to the Administration -> Firmware Upgrade page.2. Select the r9000-webupgrade.bin file you downloaded (do not select "reset to defaults after flashing").3. Click on "Upgrade".4. Wait a minimum of 5 minutes for router to flash and reboot.5.

NOTE: reset is only necessary if you run into issues or changes in firmware require it. There are two

methods of doing this:

via the "Administration -> Factory Defaults" page or via telnet/ssh nvram erase && reboot.

•

Recovery

The same rules apply for dd-wrt tftp as you would for stock below. Just make sure you grab the

factory-to-dd-wrt.IMG file.

ONLY IMG files can be TFTP'd onto the router.

Make sure you statically set the IP address on your computer to 192.168.1.2; subnet 255.255.255.0 and

gateway to 192.168.1.1.

If you want to go back to stock: All you need to do is TFTP the stock firmware back onto the router. Make

sure to factory reset dd-wrt on the admin>factory defaults tab. Grab the latest Firmware file from Netgear:

https://www.netgear.com/support/product/R9000.aspx#download

1. Get TFTP64 installed on your PC https://www.tftpd64.com/ (MAKE SURE TO ALLOW THIS

PROGRAM IN YOUR FIREWALL FOR BOTH PUBLIC AND PRIVATE NETWORKS OR YOU'LL

NEVER SEND THE IMG FILE)

2.Read how to use "TFTP client mode"-

https://kb.netgear.com/000059633/How-to-upload-firmware-to-a-NETGEAR-router-using-TFTP-client

3.Get the TFTP program up and running and ready to push the correct file onto the router- then you will wait

for step 6 below.

To put the R9000 into TFTP mode.

1. Power off the router.

2.Hold down the reset button.

Netgear_R9000

Upgrading/Downgrading DD-WRT 2

3.Power on the router and keep holding down the reset button.

4.When the router first boots the power led flashes orange and then it will switch to a slow white flash. Keep

holding down reset button. The slow white flash will change to a faster white flash and then to a second even

faster white flash. Let it blink 3-4 on the second set of faster white flashes and let go of the reset button and

now send the IMG file via TFTP. When the power LED is fast white blinking, the router is in TFTP mode and

ready to accept any IMG file (Stock or dd-wrt). You will have about 2-3 minutes to send the IMG file.

5. Go to the tftp program and re-select your NIC with the static IP 192.168.1.2 from the dropdown. It will

change as you boot the router initially so you have to go back and select the right NIC/IP in the TFTP

program. (You can avoid this by using a cheap/dumb 1gig switch which keeps your NIC active the whole time

and shouldn't have to worry about re-selecting the right NIC in the dropdown)

6. Push the file onto the router using TFTP64.

7.Wait a full 5 minutes before touching the router. It should do it's update and reboot by itself. Keep your

browser open and try to load 192.168.1.1 It should load the stock firmware gui/website automatically once the

router is booted. If the stock gui loads, clear your static NIC settings to grab IP's automatically again.

8. If 5 minutes have passed and nothing has happened performing website refreshes, then reboot the router

manually and try loading the gui website again.

GPIO

GPIO LED's

22 =Power LED

23 =WAN LED

36 =USB 1 LED

37 =USB 2 LED

30 =10Gbps LED

29 =WIFI Button LED

https:/http://wiki.dd-wrt.com/wiki.dd-wrt.comhttp://wiki.dd-wrt.com/wiki/index.php/LED_Scripts

VLAN Detached networks

Putting any of the 6 ethernet ports on a separate detached VLAN network is complicated by the fact that there

are two internal hardware switches used by R9000 for routing traffic. Creating additional Vlan's on the

R9000, right now, has not yet been "figured out" for the 6 ehternet ports.

However, the SFP+ port can be easily segregated into its own VLAN since it's the only port associated with

the eth0 interface. Read below for how to unbridge eth0, which is bridged to br0 by default .

Netgear_R9000

Recovery 3

Detaching the SFP+ port

To create a 10 gb/sec VLAN, start by setting up the SFP+ port as you would any VAP by navigating to Setup

>Networking:

Next, under the Port Setup heading, locate the group box called Network Configuration eth0 and unbridge

the interface by selecting the Unbridged radio button assigned to Bridge Assignment. Since it's going to be a

VLAN, select the Net Isolation radio button to isolate it from the rest of your network and assign IP/Subnet

mask of your choosing.

Netgear_R9000

Detaching the SFP+ port 4

Optionally, you can force DNS redirection if you want the devices on that VLAN to be forced into using a

preferred DNS server choice by enabling the Forced DNS Redirection option and entering the DNS server IP

in the Optional DNS Target text boxes.

Stop here and click Save and Apply Settings at the bottom of the page, in that order.

Finally, create a DHCP server for your newly minted VLAN by scrolling to the bottom of the same page and,

under the DHCPD heading, click the Add button to create a new DHCP server. In the ensuing list box, scroll

through the list of interfaces and select eth0, make sure it is enabled by selecting On in the neighboring list

box, leave the default lease time or modify it, click Save, then Apply Settings, in that order.

Netgear_R9000

Detaching the SFP+ port 5

Restart for good measure and begin using the SFP+ VLAN.

As for choice of SFP+ modules, note that there really isn't any meaningful speed difference between them as

shown in this Serve The Home YT video: https://www.youtube.com/watch?v=4qM9dyEuaS4

Also note that the SFP+ modules do get hot. I would change the fan threshold parameters to make sure that

your R9000 fans stay on 24/7. They aren't loud and could help keep mobo and CPU speeds in check during

the incoming summer months while transferring files at 10 gb/sec in your new VLAN.

Netgear_R9000

Detaching the SFP+ port 6

Andere Handbücher für R9000

Inhaltsverzeichnis

Andere NETGEAR Netzwerk-Router Handbücher

NETGEAR

NETGEAR DG834Gv1 - 54 Mbps Wireless ADSL Firewall... Bedienungsanleitung

NETGEAR

NETGEAR Orbi RBRE950 Bedienungsanleitung

NETGEAR

NETGEAR D8500 Bedienungsanleitung

NETGEAR

NETGEAR DG834Gv2 - 54 Mbps Wireless ADSL Firewall... Bedienungsanleitung

NETGEAR

NETGEAR ME101 - Wireless EN Bridge Network Converter Bedienungsanleitung

NETGEAR

NETGEAR FVX538v2 - ProSafe VPN Firewall Dual WAN Bedienungsanleitung

NETGEAR

NETGEAR D6200v2 Bedienungsanleitung

NETGEAR

NETGEAR Nighthawk D7000 Bedienungsanleitung

NETGEAR

NETGEAR RO318 Bedienungsanleitung

NETGEAR

NETGEAR RH348 Bedienungsanleitung

NETGEAR

NETGEAR C7800 Bedienungsanleitung

NETGEAR

NETGEAR WGE101 Bedienungsanleitung

NETGEAR

NETGEAR WNDR4500 Bedienungsanleitung

NETGEAR

NETGEAR Nighthawk CAX30 Bedienungsanleitung

NETGEAR

NETGEAR Orbi Pro SXK50 Bedienungsanleitung

NETGEAR

NETGEAR FS308 - Switch Bedienungsanleitung

NETGEAR

NETGEAR ETHERNET SWITCH SW108 Bedienungsanleitung

NETGEAR

NETGEAR RP614 v2 Bedienungsanleitung

NETGEAR

NETGEAR DGN2200M - Wireless-N 300 Router Bedienungsanleitung

NETGEAR

NETGEAR C6250 Bedienungsanleitung

NETGEAR

NETGEAR JWNR3000 Bedienungsanleitung

NETGEAR

NETGEAR WGR614 v7 Benutzerhandbuch

NETGEAR

NETGEAR RT338 Bedienungsanleitung

NETGEAR

NETGEAR Nighthawk Pro XR300 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung