NI C Series Bedienungsanleitung
GETTING STARTED GUIDE
NI 9860
2-Port, C Series Vehicle Multiprotocol Interface
Module
This document explains how to connect to the NI 9860.
Note Before you begin, complete the software and
hardware installation procedures in your chassis
documentation.
Note The guidelines in this document are specific to
the NI 9860. The other components in the system might
not meet the same safety ratings. Refer to the
documentation for each component in the system to
determine the safety and EMC ratings for the entire
system.
Safety Guidelines
Operate the NI 9860 only as described in this document.
Hot Surface This icon denotes that the component
may be hot. Touching this component may result in
bodily injury.
Caution Do not operate the NI 9860 in a manner not
specified in this document. Product misuse can result in
a hazard. You can compromise the safety protection
built into the product if the product is damaged in any
2| ni.com | NI 9860 Getting Started Guide
way. If the product is damaged, return it to NI for
repair.
Safety Guidelines for Hazardous Locations
The NI 9860 is suitable for use in Class I, Division 2, Groups A,
B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4
and Ex nA IIC T4 hazardous locations; and nonhazardous
locations only. Follow these guidelines if you are installing the
NI 9860 in a potentially explosive environment. Not following
these guidelines may result in serious injury or death.
Caution Do not disconnect I/O-side wires or
connectors unless power has been switched off or the
area is known to be nonhazardous.
Caution Do not remove modules unless power has
been switched off or the area is known to be
nonhazardous.
Caution Substitution of components may impair
suitability for Class I, Division 2.
Caution For Division 2 and Zone 2 applications,
install the system in an enclosure rated to at least IP54
as defined by IEC/EN 60079-15.
NI 9860 Getting Started Guide | © National Instruments Corporation | 3
Special Conditions for Hazardous Locations Use in
Europe and Internationally
The NI 9860 has been evaluated as Ex nA IIC T4 Gc equipment
under DEMKO Certificate No. 12 ATEX 1202658X and is
IECEx 14.0089X certified. Each NI 9860 is marked II 3G and
is suitable for use in Zone 2 hazardous locations, in ambient
temperatures of -40 °C ≤ Ta ≤ 70 °C. If you are using the NI 9860
in Gas Group IIC hazardous locations, you must use the device in
an NI chassis that has been evaluated as Ex nC IIC T4, Ex IIC
T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.
Caution You must make sure that transient
disturbances do not exceed 140% of the rated voltage.
Caution The system shall only be used in an area of
not more than Pollution Degree 2, as defined in
IEC 60664-1.
Caution The system shall be mounted in an
ATEX/IECEx-certified enclosure with a minimum
ingress protection rating of at least IP54 as defined in
IEC/EN 60079-15.
4| ni.com | NI 9860 Getting Started Guide
Caution The enclosure must have a door or cover
accessible only by the use of a tool.
Wiring the NI 9860
The NI 9860 has two ports for connecting to NI-XNET CAN/LIN
Transceiver Cables (required to connect to the CAN/LIN bus)
and a two-position connector for use with an external power
supply.
For more information about transceiver cables, refer to the
NI-XNET CAN/LIN Transceiver Cables page on ni.com.
The NI 9860 requires an external power supply of +9 to +30 V to
power the transceiver cables. Supply power to the NI 9860 VSUP
connector on the module front panel using the supplied power
cable. The exposed lead wires at the end of the power cable are
routed as follows: black wire—COM, red wire—VSUP. The
power cable lead wires may be daisy-chained to the controller
power port when the controller supply voltage is in the
appropriate range.
Note Power on VSUP is required for transceiver cable
operation.
NI 9860 Getting Started Guide | © National Instruments Corporation | 5
Note When using more than four transceiver cables
with your CompactRIO chassis, refer to the NI-XNET
CAN/LIN Transceiver Cables page on ni.com for
mounting guidelines to limit the thermal impact to your
CompactRIO system.
The following figure shows the NI 9860 with Port 1 connected to
an NI-XNET CAN HS/FD Transceiver Cable and the
two-position connector connected to the power cable. The breaks
in the cables represent additional cable length.
6| ni.com | NI 9860 Getting Started Guide
Figure 1. NI 9860 with Power and Transceiver Cables Attached
NI 9860 Hardware Overview
The NI 9860 is a two-port C-Series module based on the XNET
architecture. Users can choose the physical bus protocol by
plugging in the corresponding transceiver cable. The NI 9860
NI 9860 Getting Started Guide | © National Instruments Corporation | 7
supports hot-swapping of transceiver cables and can detect and
identify transceiver cable types.
For more information about transceiver cables, refer to the
NI-XNET CAN/LIN Transceiver Cables page on ni.com.
Figure 2. NI 9860 Hardware Overview
Ext Pwr
Supply
Required
Controller
COM
Vsup
+
_
Pwr Sup
Controller
Port 1
Port 2
Transceiver
Cable
Transceiver
Cable
Inserting and Removing the NI-XNET
Transceiver Cable
The NI-XNET Transceiver Cable connects to a host device with
an active latching connector. To connect the NI-XNET
8| ni.com | NI 9860 Getting Started Guide
Transceiver Cable to a host device, push the connector assembly
into the host receptacle until the internal latch snaps into position.
The latch emits an audible click when engaged. To remove the
NI-XNET Transceiver Cable, push the lock ejector forward to
disengage the latch and simultaneously pull the NI-XNET
Transceiver Cable, as shown in the following figure.
Figure 3. Inserting and Removing the NI-XNET Transceiver Cable
Push Lock
Ejector Forward
Pull Cable
Inserting and Removing the Power Cable
The NI 9860 connects to the provided power cable with an active
latching connector. To connect the power cable, push the end of
the power cable into the two-position connector until the internal
NI 9860 Getting Started Guide | © National Instruments Corporation | 9
latch snaps into position. The latch emits an audible click when
engaged.
To remove the power cable, push the lock ejector down to
disengage the latch and simultaneously pull the power cable
away from the module, as shown in the following figure.
Figure 4. Removing the NI 9860 Power Cable
Pull Power
Cable
Push Lock
Ejector Down
10 | ni.com | NI 9860 Getting Started Guide
Andere Handbücher für C Series
3
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere NI Steuereinheit Handbücher
NI
NI USB-6008 Bedienungsanleitung
NI
NI REM-11175 Bedienungsanleitung
NI
NI PXI-6682 Bedienungsanleitung
NI
NI PXIe-1487 Bedienungsanleitung
NI
NI 9866 Bedienungsanleitung
NI
NI PXIe-8623 Betriebsanleitung
NI
NI USB-6008 Stücklistenhandbuch
NI
NI PXIe-1486 Bedienungsanleitung
NI
NI FlexRIO PXIe-7976R Bedienungsanleitung
NI
NI REM-11190 Bedienungsanleitung
NI
NI ISM-7412 Bedienungsanleitung
NI
NI 9512 C Series Bedienungsanleitung
NI
NI TBX-2808 Bedienungsanleitung
NI
NI SCXI-1160 Kurzanleitung
NI
NI 9770 Bedienungsanleitung
NI
NI PXIe-7975 Bedienungsanleitung
NI
NI 9265E Bedienungsanleitung
NI
NI 9266 Bedienungsanleitung
NI
NI LabVIEW Bedienungsanleitung
NI
NI PXI-4204 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
