NI SbRIO-9697 Bedienungsanleitung

sbRIO-9697

Getting Started

2022-07-06

Contents

Installation Purpose (RIO Mezzanine Card). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Kit Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Digital I/O Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installing the NI 9697. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.3 V Digital I/O on 50-Pin IDC Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Physical Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Environmental. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Environmental Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

EU and UK Customers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

电子信息产品污染控制管理办法（中国 RoHS）. . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Worldwide Support and Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

ni.com

sbRIO-9697 Getting Started

Installation Purpose (RIO Mezzanine Card)

The NI 9697 two-slot C Series RIO Mezzanine Card is an accessory you can use to

connect up to two board-only C Series modules to the NI sbRIO-9607/9627.

sbRIO RMC Interface Connector

C Series

Module

C Series

Module

3.3 V

Digital I/O

5 V

Power Supply

x 24

Note NI recommends using the NI 9693 with the NI sbRIO-9605/9606 or

the NI sbRIO-9623/9626 as the NI 9697 is not compatible with these

products.

Note Board-only C Series modules are represented with an 'E' at the end

of the product name. For example, the NI 9219 is the enclosed C Series

module and the NI 9219E is the board-only version of the module.

Kit Contents

The NI 9697 kit contains the following components:

sbRIO-9697 Getting Started

Figure 1. Contents of the NI 9697 Kit

1. M3 × 7 mm Silver Low-Profile Screw (x7)

2. M3 × 4 mm Black Low-Profile Screw (x10)

3. NI 9697

4. C Series Module Support Bracket (x3)

5. Isolator Sheet

6. M3 × 7 mm Stando (x6)

Caution NI makes no electromagnetic compatibility (EMC) or CE marking

compliance claims for the NI 9697. The end-product supplier is responsible

for conformity to any and all compliance requirements.

Caution The NI 9697 must be installed inside a suitable enclosure prior to

use. Hazardous voltages may be present.

ni.com

sbRIO-9697 Getting Started

Caution Follow proper ESD precautions to ensure you are grounded

before installing hardware.

Caution The protection provided by the NI 9697 can be impaired if the NI

9697 is used in a manner not described in this document.

Digital I/O Connector Pinouts

The following figure shows the pinouts of the I/O connector on the NI sbRIO device.

Figure 2. Pinout of the DIO Connector

J1, DIO

+5V

D GND

+5V

DIO22

DIO21

DIO19

DIO18

DIO17

DIO16

DIO23

DIO20

DIO15

DIO14

DIO13

DIO12

DIO11

DIO10

DIO9

DIO8

DIO7

DIO6

DIO5

DIO4

DIO3

DIO2

DIO1

DIO0

1 2

3 4

5 6

7 8

910

11 12

13 14

15 16

17 18

19 20

21 22

23 24

25 26

27 28

29 30

31 32

33 34

35 36

37 38

39 40

41 42

43 44

45 46

47 48

49 50

Pin 1

Note The DIO numbering on this connector corresponds to naming of the

DIO on the NI sbRIO device. For example, DIO0 on the NI 9697 connector

corresponds to DIO0 on the NI sbRIO-9607/9627 RMC connector.

sbRIO-9697 Getting Started

Installing the NI 9697

What to use:

■Socket driver, 4.5 mm

■Screwdriver, Phillips #1

Complete the following steps to install the NI 9697.

1. Attach the three C Series support brackets to the NI 9697 using six of the M3 ×

4 mm black, low-profile screws included in the kit.

Note Do not tighten the screws until you reach step 8. You may need

to adjust the brackets during assembly.

Figure 3. Attaching the Support Brackets to the NI 9697

2. Connect board-only C Series modules to the NI 9697.

Caution To avoid causing damage to the NI 9697 and the C Series

modules, do not allow C Series module support brackets to contact

ni.com

sbRIO-9697 Getting Started

components on the secondary side of the board-only C Series

modules.

Figure 4. Connecting Board-only C Series Modules to the NI 9697

3. Screw three of the remaining M3 × 4 mm black, low-profile screws into the

holes.

Figure 5. Inserting Three Screws into the Module and Bracket Holes

4. Insert the six M3 × 7 mm standos from the secondary side of the NI sbRIO

device into the six mounting standos for your application. The mounting

standos are not included in the NI 9697 kit.

Note You can attach the NI 9697 to an NI sbRIO-9607. You must

support the NI 9697 mounting holes that overhang the NI sbRIO

sbRIO-9697 Getting Started

device with standos that are 9.2 mm (0.36 in.) taller than the

mounting standos described in step 4.

Figure 6. Inserting the Standos into the NI sbRIO Device

1. M3 × 7 mm Stando (x6)

2. sbRIO Device

3. Mounting Stando (x6, Not Provided)

5. Tighten the standos to 0.45 N · m (4.0 lb · in.). Do not overtighten.

6. Press the isolator sheet over the standos so that 1 mm to 2 mm of stando

protrudes through the holes.

7. Align the bracket holes attached to the NI 9697 with the tops of the M3 × 7 mm

standos, and insert the six M3 × 7 mm silver low-profile screws.

ni.com

sbRIO-9697 Getting Started

Figure 7. Inserting the Standos and Screws into the NI sbRIO Device

1. M3 × 7 mm Silver Low-Profile Screw (x6)

2. NI 9697

3. Isolator

8. Tighten all the screws to 0.45 N · m (4.0 lb · in.). Do not overtighten.

The following figures show the dimensions of the assembled NI 9697 and NI sbRIO

device with two board-only C Series modules.

sbRIO-9697 Getting Started

Figure 8. Side View with Dimensions

71.70 mm

(2.820 in.)

13.40 mm

(0.530 in.)

9.20 mm

(0.360 in.)

Figure 9. Rear View with Dimensions

18.0 mm

(0.71 in.)

73.6 mm

(2.90 in.)

73.6 mm

(2.90 in.)

1. Recommended Keepaway from Modules

Tip For two-dimensional drawings and three-dimensional models of the

NI 9697, visit ni.com/dimensions and search by model number.

Specifications

Refer to the documentation for the NI sbRIO device and the board-only C Series

modules for the specifications of those products.

3.3 V Digital I/O on 50-Pin IDC Connector

Number of DIO channels 24

Maximum tested current per channel ±3 mA

Input logic levels

Input low voltage, VIL 0 V min; 0.8 V max

Input high voltage, VIH 2.0 V min; 5.25 V max

ni.com

sbRIO-9697 Getting Started

Inhaltsverzeichnis

Andere NI Steuereinheit Handbücher

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung

NI sbRIO-9697 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken