NI REM-11190 Bedienungsanleitung
-~
ARTISAN
®
~I
TECHNOLOGY
GROUP
Your definitive source
for
quality
pre-owned
equipment.
Artisan Technology
Group
Full-service,
independent
repair
center
with
experienced
engineers
and
technicians
on staff.
We
buy
your
excess,
underutilized,
and
idle
equipment
along
with
credit
for
buybacks
and
trade-ins
.
Custom
engineering
so
your
equipment
works
exactly as
you
specify.
•
Critical
and
expedited
services
•
Leasing
/
Rentals/
Demos
• In
stock/
Ready-to-ship
•
!TAR-certified
secure
asset
solutions
Expert
team
ITrust
guarantee
I
100%
satisfaction
All
tr
ademarks,
br
a
nd
names, a
nd
br
a
nd
s a
pp
earing here
in
are
th
e property of
th
e
ir
r
es
pecti
ve
ow
ner
s.
Visit our website - Click HERE
GETTING STARTED GUIDE
NI REM-11190
Bus Power Module for Remote I/O
This document explains how to connect to the REM-11190.
Note The guidelines in this document are specific to the REM-11190. The other
components in the system might not meet the same safety ratings. Refer to the
documentation for each component in the system to determine the safety and EMC
ratings for the entire system.
Caution Do not operate the REM-11190 in a manner not specified in this
document. Product misuse can result in a hazard. You can compromise the safety
protection built into the product if the product is damaged in any way. If the product
is damaged, return it to NI for repair.
Isolation Withstand Voltages
Test section Test voltage
5 V communications power (logic), 24 V supply (I/O) 500 VAC, 50 Hz, 1 min.
5 V supply (logic)/functional earth ground 500 VAC, 50 Hz, 1 min.
24 V supply (I/O)/functional earth ground 500 VAC, 50 Hz, 1 min.
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits for
electromagnetic compatibility (EMC) stated in the product specifications. These requirements
and limits provide reasonable protection against harmful interference when the product is
operated in the intended operational electromagnetic environment.
This product is intended for use in industrial locations. However, harmful interference may
occur in some installations, when the product is connected to a peripheral device or test object,
or if the product is used in residential or commercial areas. To minimize interference with
radio and television reception and prevent unacceptable performance degradation, install and
use this product in strict accordance with the instructions in the product documentation.
Furthermore, any changes or modifications to the product not expressly approved by National
Instruments could void your authority to operate it under your local regulatory rules.
Preparing the Environment
Ensure that the environment in which you are using the REM-11190 meets the following
specifications.
Operating temperature -25 °C to 60 °C
Operating humidity 5% RH to 95% RH, noncondensing
Pollution Degree 2
Maximum altitude 3,000 m
Indoor use only.
Note Refer to the device datasheet on ni.com/manuals for complete specifications.
2| ni.com | REM-11190 Getting Started Guide
Verifying the Kit Contents
Verify that the following items are included in the REM-11190 kit.
Figure 1. REM-11190 Kit Contents
12 3
1. NI REM-11190
2. Red Bus connector
3. Supply voltage connector
Unpacking the Kit
Caution To prevent electrostatic discharge (ESD) from damaging the device,
ground yourself using a grounding strap or by holding a grounded object, such as
your computer chassis.
1. Touch the antistatic package to a metal part of the computer chassis.
2. Remove the device from the package and inspect the device for loose components or any
other sign of damage.
Caution Never touch the exposed pins of connectors.
Note Do not install a device if it appears damaged in any way.
3. Unpack any other items and documentation from the kit.
Store the device in the antistatic package when the device is not in use.
REM-11190 Getting Started Guide | © National Instruments | 3
Installing the REM-11190
Figure 2. Structure of the REM-11190
1
34
5
2
1. Bus connector
2. REM-11190
3. Module function label
4. Supply voltage connector
5. LED indicators
Table 1. Module Function Labels
Label Color Module Function
Blue Digital input
Red Digital output
Green Analog input, thermocouple
Yellow Analog output
White Bus coupler, power module
Installing Bus Connectors
What to Use
• Bus connector
• DIN rail
What to Do
Complete the following steps to install bus connectors on the DIN rail.
4| ni.com | REM-11190 Getting Started Guide
1
2
1. Insert the bus connector for the REM-11190 into the DIN rail.
Note Verify that you are using the red bus connector. The REM-11190 will
not function if you mount it on any other bus connector.
2. Slide the bus connector along the DIN rail until it connects to the preceding bus
connector.
Note A bus connector will not attach to a preceding bus connector with a
mounted module. Remove the preceding module before installing additional
bus connectors.
3. Repeat Steps 2 and 3 for additional bus connectors.
Installing the Module
What to Use
• REM-11190
• Mounted bus connector
What to Do
Complete the following steps to install the REM-11190 on the DIN rail.
REM-11190 Getting Started Guide | © National Instruments | 5
1. Align the REM-11190 over the appropriate bus connector.
Note Verify that the bus connector socket aligns with the socket on the
underside of the module.
2. Press the REM-11190 directly onto the bus connector and DIN rail until it clicks into
place.
Caution Tilting the module when mounting it on the DIN rail will damage the
contacts.
Installing Spring-Terminal Blocks
What to Use
• REM-11190
• Spring-terminal block
What to Do
Align the spring-terminal block over the REM-11190 and press until it clicks into place.
6| ni.com | REM-11190 Getting Started Guide
REM-11190 Pinout
a1
a2
b1
b2
24 VDC GND
GND24 VDC
Table 2. REM-11190 Signal Descriptions
Signal Color Description
a1, a2 Red 24 VDC (UL) Supply of logic voltage (internally jumpered)
b1, b2 Blue GND Reference potential of the supply voltage (internally
jumpered)
Figure 3. REM-11190 LEDs
UL
E1
Table 3. LED Indicators
LED LED Color LED Pattern Indication
UL
Green Solid Communications power UBus is present.
Red Solid
• Communications power UBus is not present.
• Communications power UBus downstream of the
power module is not present.
— Off Communications power supply not present.
E1
Red Solid Module mounted on incorrect bus connector
— Off No error
REM-11190 Getting Started Guide | © National Instruments | 7
Connecting the REM-11190
24 VDC
F1
+
–
24 VDC
F2
+
–
a1
a2
b1
b2
a1
a2
b1
b2
REM-11190
a1 b1
a2 b2
REM-111xx
REM-111xx
The supply terminals blocks contain internal jumpers. You can use the first connection for
supply and the second connection to forward a potential to the next module.
Caution Connect an 8 A external fuse to the 24 V UL supply to protect against
polarity reversal. The power supply must provide four times the nominal current of
the external fuse. This rating ensures that the fuse trips in the event of an error.
Connection Guidelines
• Make sure that devices you connect to the REM-11190 are compatible with the module
specifications.
• Push the wire into the terminal when using a solid wire or a stranded wire with a ferrule.
• Open the terminal by pressing a screwdriver into the spring lever when using a stranded
wire without a ferrule.
8| ni.com | REM-11190 Getting Started Guide
Removing Components
Removing Spring Terminal Blocks
Complete the following steps to remove a spring-terminal block from the REM-11190.
1
3
2
1
1. Press the locking latch to release the spring-terminal block.
2. Tilt the block toward the center of the module.
3. Remove the connector from the module.
Removing the REM-11190
Remove all connections before removing the REM-11190, either by disconnecting the cables
or removing the spring-terminal block.
What to Use
• Flathead Screwdriver
What to Do
Complete the following steps to remove the REM-11190 from the DIN rail.
1
1
2
1. Insert the screwdriver and loosen the base latches on either end of the module.
2. Remove REM-11190 perpendicular to the DIN rail.
REM-11190 Getting Started Guide | © National Instruments | 9
Inhaltsverzeichnis
Andere NI Steuereinheit Handbücher
NI
NI DAQPad-6016 OEM Bedienungsanleitung
NI
NI LabVIEW Bedienungsanleitung
NI
NI 9217 Bedienungsanleitung
NI
NI SCC Series Bedienungsanleitung
NI
NI 9247 Bedienungsanleitung
NI
NI PCMCIA-FBUS Bedienungsanleitung
NI
NI NI-9205 Bedienungsanleitung
NI
NI SCXI-1127 Bedienungsanleitung
NI
NI PXIe-8623 Betriebsanleitung
NI
NI FlexRIO PXIe-7976R Bedienungsanleitung
NI
NI 9866 Bedienungsanleitung
NI
NI GPIB Series Montageanleitung
NI
NI SCC-RLY01 Bedienungsanleitung
NI
NI 9770 Bedienungsanleitung
NI
NI ELVIS RIO Bedienungsanleitung
NI
NI USB-6008 Bedienungsanleitung
NI
NI FieldPoint cFP-RLY-423 Bedienungsanleitung
NI
NI IMAQ PCI-1409 Bedienungsanleitung
NI
NI NI-9223 Bedienungsanleitung
NI
NI 9201E Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
