Nibe F110 Bedienungsanleitung

IHB EN 1927-6

231974

INSTALLATION MANUAL

Hot water heat pump

NIBE F110

LEK

Quick guide

Navigation Ok button (confirm/select)

Back button (back/undo/exit)

Up/down buttons

(move/increase/reduce)

A detailed explanation of the button functions can be found on page 22.

How to scroll through menus and make different settings is described on page 24.

Increase hot water volume

true

off

To temporarily increase the amount of hot water, first press the down button to mark menu 2 (water droplet)

and then press the OK button twice. Read more about the settings on page 26.

In event of disturbances in comfort

If a disturbance in comfort of any type occurs there are some measures that can be taken before you need to

contact your installer. See page 34 for instructions.

41 Important information

4Safety information

4Symbols

4Marking

5Serial number

5Recovery

6Inspection of the installation

72 Delivery and handling

7Transport

7Assembly

8Supplied components

8Removing the covers

103 The Heat pump design

10Component positions

11List of components

124 Pipe and air connections

12General pipe connections

13Dimensions and pipe connections

14Installation alternative

16General ventilation connections

17Dimension and ventilation connections

17Ventilation flow (exhaust air)

17Adjusting ventilation (exhaust air)

185 Electrical connections

18General

18Connections

19Optional connections

206 Commissioning and adjusting

20Preparations

20Filling and venting

20Start-up and inspection

227 Control - Introduction

22Display unit

22Menu system

258 Control - Menus

25Menu 1 - ventilation

26Menu 2 - HOT WATER

28Menu 3 - INFO

29Menu 4 - MY SYSTEM

30Menu 5 - SERVICE

339 Service

33Service actions

3410 Disturbances in comfort

34Info menu

34Manage alarm

3611 Accessories

36Separable valve connector

36Base extension EF 45

36Top cabinet

3712 Technical data

37Dimensions and setting-out coordinates

38Technical specifications

39Energy labelling

40Electrical circuit diagram

41Item register

43Contact information

3Table of ContentsNIBE F110

Table of Contents

Safety information

This manual describes installation and service proced-

ures for implementation by specialists.

The manual must be left with the customer.

This appliance can be used by children

aged from 8 years and above and persons

with reduced physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given super-

vision or instruction concerning use of the

appliance in a safe way and understand

the hazards involved. Children shall not

play with the appliance. Cleaning and user

maintenance shall not be made by children

without supervision.

Rights to make any design or technical

modifications are reserved.

©NIBE 2019.

Water may drip from the safety valve’s

overflow pipe. The entire length of the over-

flow water pipe must be routed to a suitable

drain and be inclined to prevent water pock-

ets, and must also be frost-proof. The over-

flow pipe must be at least the same size as

the safety valve. The overflow pipe must be

visible and its mouth must be open and not

located close to electrical components.

Symbols

NOTE

This symbol indicates danger to person or ma-

chine .

Caution

This symbol indicates important information

about what you should consider when installing

or servicing the installation.

TIP

This symbol indicates tips on how to facilitate

using the product.

Marking

The CE mark is obligatory for most products sold

in the EU, regardless of where they are made.

Classification of enclosure of electro-technical

equipment.

IP21

Read the User Manual.

Read the Installer Manual.

NIBE F110Chapter 1 | Important information4

1 Important information

Serial number

The serial number can be found at the bottom right of

the front cover.

Serial number

Caution

You need the product's (14 digit) serial number

for servicing and support.

Recovery

Leave the disposal of the packaging to the in-

staller who installed the product or to special

waste stations.

Do not dispose of used products with normal

household waste. It must be disposed of at a

special waste station or dealer who provides this type

of service.

Improper disposal of the product by the user results in

administrative penalties in accordance with current le-

gislation.

5Chapter 1 | Important informationNIBE F110

Inspection of the installation

Current regulations require the heating installation to be inspected before it is commissioned. The inspection must

be carried out by a suitably qualified person.

DateSigna-

ture

NotesDescription

✔

Ventilation, exhaust air (page 14)

Setting the ventilation flow

Exhaust air filter

Ventilation, surrounding air or outdoor air

(page 15)

Pressure drop in the system

Hot water

System vented

Electricity (page 18)

Supply connected 230 V

Circuit fuses

Earth circuit-breaker

Miscellaneous

Type of installation

NIBE F110Chapter 1 | Important information6

Transport

F110 should be transported and stored vertically in a dry

place. However. the F110 may be carefully laid on its

back when being moved into a building. The centre of

gravity is in the upper part.

Assembly

• Position F110 on a solid foundation indoors that with-

stands water and the weight of the heat pump. Use

the product’s adjustable feet to obtain a horizontal and

stable set-up.

30 - 50 mm

15 - 40 mm

20-55 mm

• Because water comes from F110, the area where the

heating pump is located must be equipped with floor

drainage.

•Install with its back to an outside wall, ideally in a room

where noise does not matter, in order to eliminate

noise problems. If this is not possible, avoid placing

it against a wall behind a bedroom or other room

where noise may be a problem.

• Wherever the unit is located, walls to sound sensitive

rooms should be fitted with sound insulation.

• Route pipes so they are not fixed to an internal wall

that backs on to a bedroom or living room.

• The heat pump's installation area should always have

a temperature of at least 10 °C and max 30 °C.

INSTALLATION AREA

Leave a free space of 800 mm in front of the product.

Leave free space between F110 and wall/other ma-

chinery/fittings/cables/pipes etc. It is recommended that

a space of at least 10 mm is left to reduce the risk of

noise and of any vibrations being propagated.

800

10-50*10-50*

* Depending on whether the panels can be removed or

not.

NOTE

Ensure that there is sufficient space (300 mm)

above F110 for installing ventilation hoses.

7Chapter 2 | Delivery and handlingNIBE F110

2 Delivery and handling

Supplied components

Mora kniv

LEK

Filter cartridgeSilencer

Air connection

LOCATION

The kit of supplied items is placed in the lower section

of the product.

Removing the covers

AIR TREATMENT HATCH

LEK

1. Slacken off the screws for the securing plate above

F110.

2. Slide the hatch upwards and pull it towards you.

3. Pull the hatch towards yourself.

NOTE

An earth cable is installed in the hatch, which

can therefore only be lifted out 35 cm. If the

hatch needs to be removed completely, the

cable must be disconnected.

FRONT COVER

Remove the front hatch by pulling it straight out.

LEK

NOTE

A display cable is installed in the hatch, it can

therefore only be lifted out 1.5 m. If the hatch

needs to be removed completely, the cable

must be detached.

NIBE F110Chapter 2 | Delivery and handling8

SIDE PANELS

Air treatment section

1. Undo the screws at the edge.

2. Twist the cover slightly outward.

3. Move the side cover outwards and backwards.

4. Assembly takes place in the reverse order.

LEK

Heater section

1. Undo the screws at the edge.

2. Twist the cover slightly outward.

3. Move the side cover outwards and backwards.

4. Assembly takes place in the reverse order.

LEK

9Chapter 2 | Delivery and handlingNIBE F110

Component positions

LEK

AA4

XL43

XL44

BT77 QM25

BT7

WM1

BT35

EB1

FL1

XL3 XL4

AA2

PF1

GP12

BP1

QN20

CA1

GQ1

FL6FQ1

BT12

GQ10

EB10

PF1

BT6

QM30

BT76

QN1

BT16

EP1

EP2

HZ2

BT13

PF3

QM5

WM2

NIBE F110Chapter |10

Andere Handbücher für F110

Inhaltsverzeichnis

Andere Nibe Wärmepumpe Handbücher

Nibe

Nibe HBS 05 Series Benutzerhandbuch

Nibe

Nibe F1255 Series Benutzerhandbuch

Nibe

Nibe F2040 Series Bedienungsanleitung

Nibe

Nibe F2120 Series Benutzerhandbuch

Nibe

Nibe S2125 Benutzerhandbuch

Nibe

Nibe S2125 Bedienungsanleitung

Nibe

Nibe F2025 Bedienungsanleitung

Nibe

Nibe VVM S320 Benutzerhandbuch

Nibe

Nibe F1155 Series Bedienungsanleitung

Nibe

Nibe F130 Benutzerhandbuch

Nibe

Nibe S2125 Bedienungsanleitung

Nibe

Nibe AG-WL10 series Benutzerhandbuch

Nibe

Nibe S1255PC Benutzerhandbuch

Nibe

Nibe PCS 44 Benutzerhandbuch

Nibe

Nibe F730 Bedienungsanleitung

Nibe

Nibe FIGHTER 640P Bedienungsanleitung

Nibe

Nibe Fighter 2005 Original Betriebsanleitung

Nibe

Nibe FIGHTER 1240 Bedienungsanleitung

Nibe

Nibe AMS 10-8 Benutzerhandbuch

Nibe

Nibe F2300 Bedienungsanleitung

Nibe

Nibe FIGHTER 600P Bedienungsanleitung

Nibe

Nibe F205P Bedienungsanleitung

Nibe

Nibe VVM S320 Benutzerhandbuch

Nibe

Nibe F1155 Series Bedienungsanleitung

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung