Nibe Contura C 710 Bedienungsanleitung

Installation

Instructions

www.contura.eu

C 710

50 CERTIFICATE

PRODUCT

Product type Stove lit with solid biofuels

Type designation Contura 710

Manufacturing number See rating plate on the stove

Intended area of use Heating of rooms in residential buildings

Fuel Wood

MANUFACTURER

Name NIBE AB / Contura

Address Box 134, Skulptörvägen 10

SE-285 23 Markaryd, Sweden

CHECKS

According to AVCP System 3

European standard EN 13240:2001 / A2:2004

Test institute Rein-Ruhr Feuerstätten Prüfstelle, NB 1625,

has checked declared performance and issued test report no. RRF-40 16 4237

Declaration of performance according

to Regulation (EU) 305/2011

No. C710-CPR-160329-SE-1

DECLARED PERFORMANCE

Essential characteristics Performance Harmonised technical

speciﬁcation

Reaction to fire A1 WT

Minimum distance to combustible material Rear: 100 mm

Side: 450 mm

Other safety distances according to

the installation instructions

Risk of falling embers Pass

Emissions from combustion CO 0.1%

NOx 103 mg/m3

OGC 77 mg/m3

PM 23 mg/m3

Surface temperatures Pass

Cleaning options Pass

Mechanical durability Pass

Emissions of hazardous substances Pass

Nominal output 5 kW

Efficiency 80%

Flue gas temperature in connector at nominal

output

315°C

EN 13240:2001 / A2:2004

The undersigned is responsible for the manufacture and conformity with the declared performance.

Niklas Gunnarsson, Business area manager NIBE STOVES

Markaryd, March 29, 2016

Table of contents

Technical details 52

Prior to installation 52

Connection to chimney 53

Supply of combustion air 54

Installation distance 55

Installing 56

Removing the loose parts 58

A warm welcome to Contura.

A warm welcome to the Contura family. We hope

you will get a great deal of pleasure from your new

stove. As a new owner of a Contura stove you have

secured a product with timeless design and long

service life. Contura also has combustion that is both

environmentally friendly and efficient for the best heat

production.

Read through these installation instructions carefully

before installation. Read how to best light your stove

in the lighting instructions.

NOTE!

Report the installation of a stove to your local

authority.

The owner of the house is personally responsible

for ensuring compliance with the mandatory safety

requirements and must have the installation approved by

a qualified inspector. Your local chimney sweep must also

be informed about the installation as this will affect the

routines for regular chimney-sweeping services.

WARNING!

The stove becomes very hot

During operation, certain surfaces of the stove become

very hot and can cause burn injury if touched. Be aware

of the strong heat radiated through the hatch glass.

Placing flammable material closer than the safe distance

indicated may cause a fire. Pyre lighting can cause quick

gas ignition with the risk of damage to property and

personal injury.

CONTENTS

52 FACTS

Output 3-7kW

Nominal output 5 kW

Efficiency up to 80%

Model 710

Height (mm) 1151

Width (mm) 459

Depth (mm) 372

Weight (kg) 103

Type approved in accordance with:

European standard EN-13240

NS 3059 (Norway)

DIN Plus, RRF-40 16 4237 (Germany)

Art. 15a B-VG (Austria)

Clean Air Act. (UK)

Prior to installation

If the insert needs to be put down

to be moved or if the pillar foot is

to be installed, remove any loose

components. This is described at the

end of these installation instructions.

1 Fire bars

2 Grate disc

3 Heat deflector

4 Hearth cladding

Installation by authorised

technician

This manual contains instructions about

how the stoves must be assembled and

installed. To ensure the function and safety

of the stove, we recommend that the

installation is carried out by an authorised

technician. Contact one of our dealers who

can recommend suitable technicians.

Building application

These main insructions may give guidance

which would contravene national building

regulations. Please refer to supplementary

instructions or ask your local authority for

advice regarding building regulations.

Before installing a stove or erecting a

chimney it is necessary for you to make

a building application permission to your

local authority.

Structural support

Check that the wood joists are strong

enough to bear the weight of the stove and

chimney. The stove and chimney can usually

be placed on a normal wooden joist in a

single occupancy house if the total weight

does not exceed 400 kg.

Hearth plate

Due to the risk of falling embers, a

flammable floor must be protected by a

hearth plate. It must extend 300 mm in

front of the stove and 100 mm on each side

of the stove, or have a 200 mm extension

on each side of the opening. The hearth

plate can consist of natural stone, concrete,

metal plate or glass. A painted metal

or glass hearth plate is available as an

accessory for these models.

Important to remember!Technical details

CHIMNEY

Connection to chimney

Rear connection to a masonry chimney

Top connection to the chimney

Make sure that the connector

gasket does not work loose when

the connection pipe is placed

on the connector. If further

sealing material is required, heat-

resistant sealant may be used.

The back panel must be installed before the stove is rear connected.

The hot air grille must be installed before chimney top

connection.

• The stove meets the requirements for connecting to chimneys

dimensioned for 350°C flue gas temperature.

• The external diameter of the connection sleeve is 150 mm.

• The stove requires a draft in the chimney of at least –12 Pa. The

draft is affected both by the length and area of the chimney, and

by how well sealed it is. Minimum recommended chimney length

is 3.5 m and suitable cross section area is 150-200 cm² (140-160

mm in diameter).

• A flue with sharp bends and horizontal routing reduces the

draught in the chimney. Maximum horizontal flue is 1 m, on the

condition that the vertical flue length is at least 5 m.

• It must be possible to sweep the full length of the flue and the

soot hatches must be easily accessible.

• Carefully check that the chimney is sealed and that there is no

leakage around soot hatches and flue connections.

In the bag with these installation instructions

are two wing screws for the cover.

ca 180 mm

2 31

5 64

54 SUPPLY AIR

Supply of combustion air

When a stove is installed in a room, the demand for air supply to

the room increases. Air can be provided indirectly via a vent in

the outer wall or via a duct from the outside that is connected to

the connector on the underneath of the stove. The amount of air

needed for combustion is 25m3/h.

The connector has an external diameter of 67 mm. When duct

routing further than 1 m the pipe diameter must be increased to

100 mm and a correspondingly larger wall vent must be selected.

In hot areas the duct should be insulated with 30 mm mineral wool

covered with a moisture inhibitor (plastic). It is important that the

lead-in between the pipe and the wall (or floor) is sealed using

jointing compound.

A 1 m length of condensation insulated ducting for combustion air

is available as an accessory.

Through the external wall.

Indirect air supply through the external wall.

Through floor and foundation slab.

Through floor and wall-and-cavity foundation.

In the back and floor plates there are

knockouts that must be removed to insert

the pipe.

Installation variants

Leave a 40 mm gap between

the condensation insulation

and the bottom of the stove.

40 mm

INSTALLATION DISTANCES

C 710

* If the stove is placed on a hearth plate made of glass for example (accessory), the height from the floor is affected by a distance corresponding to the thickness of the hearth plate. Also applies to

separate glass hearth plates (accessory).

** We recommended the same side distance as to combustible walls to prevent discolouration of painted non-flammable walls.

The minimum distance in front of

the stove opening to combustible

parts of the building or interior

decoration must be at least 1 m.

The dimension diagrams only

show the minimum permitted

installation distances for the

stove. When connecting to a steel

flue, also note the safety distance

requirements of the flue. The

safety distance between an un-

insulated flue and a combustible

part of the building should be at

least 450 mm.

Installation distances

A = height from floor to chimney

connection upwards

B = height from floor to c/c chimney

connection rear

C = height from floor to air inlet

D = height from floor to lower edge

of hatch

Permitted area

for combustible

parts of the

building

A separate glass hearth

plate (accessory)

increases the connection

height to the chimney by

6 mm.

D 433

100*

459

1151

2100*

Combustible roof

372

176

A 1116*

178

B 1026*

C 420

Ø150

Air inlet Ø67

100

292

553

100

610

Combustible wall

453

225**

700

1100

228

50**

Fire-retardant wall of

brick or concrete

900

242

503

50**

540

Fire-retardant wall of

brick or concrete

678

450

540

278

100

Combustible wall

56 ASSEMBLY

Assembly

Final inspection of the installation

It is extremely important that the installation is inspected by an authorised chimney sweep before

the stove is used. Also read the ”Lighting instructions”, before lighting for the first time.

ASSEMBLY

58 REMOVAL

How to remove the hearth surround

Handle the vermiculite with care. Lift the smoke baffle with one hand whilst

removing the sides. The side posts need not be removed when sweeping.

Reinstall in reverse order

How to remove the heat deflector

Andere Nibe Holzofen Handbücher

Nibe

Nibe C856T Style Bedienungsanleitung

Nibe

Nibe Contura 890T Style Bedienungsanleitung

Nibe

Nibe Contura 690AG Style Bedienungsanleitung

Nibe

Nibe Contura 620T Bedienungsanleitung

Nibe

Nibe Contura 590T Bedienungsanleitung

Nibe

Nibe Contura 896 Style Bedienungsanleitung

Nibe

Nibe Contura C610AG Bedienungsanleitung

Nibe

Nibe Contura C590T Bedienungsanleitung

Nibe

Nibe Contura C870 Bedienungsanleitung

Nibe

Nibe Flakt Contura C600 Bedienungsanleitung

Nibe

Nibe Contura 690AG Style Bedienungsanleitung

Nibe

Nibe Contura 596T Bedienungsanleitung

Nibe

Nibe Contura C 720T Bedienungsanleitung

Nibe

Nibe Contura 870G Style Bedienungsanleitung

Nibe

Nibe Contura 590T Bedienungsanleitung

Nibe

Nibe Contura C890T Style Bedienungsanleitung

Nibe

Nibe Contura C596T Bedienungsanleitung

Nibe

Nibe Contura C890G Bedienungsanleitung

Nibe

Nibe Contura C896 Style Bedienungsanleitung

Nibe

Nibe Contura C520 Bedienungsanleitung

Nibe

Nibe Contura 610AG Style Bedienungsanleitung

Nibe

Nibe Contura 886G Style Bedienungsanleitung

Nibe

Nibe Contura C856T Bedienungsanleitung

Nibe

Nibe Contura 856G Style Bedienungsanleitung

Beliebte Holzofen Handbücher anderer Marken

Plamen

Plamen ECO MINIMAL 50 Bedienungsanleitung

RAIS

RAIS 800 Bedienungsanleitung

Henley

Henley Arklow Bedienungsanleitung

Jøtul

Jøtul F 500 Bedienungsanleitung

Englander

Englander BLUE RIDGE 100 Bedienungsanleitung

WoodPro

WoodPro WS-TS-1500 Bedienungsanleitung

Contura

Contura C 586W Bedienungsanleitung

Nordpeis

Nordpeis N-20 T Bedienungsanleitung

Palazzetti

Palazzetti EVA Konfigurationshandbuch

Lopi

Lopi 1250 Republic Bedienungsanleitung

Panadero

Panadero CAPRI 3V Programmierhandbuch

RAIS

RAIS RONDO 92 Bedienungsanleitung

RAIS

RAIS attika NEXO 100 GAS Bedienungsanleitung

ADURO

ADURO 15-3 Benutzerhandbuch

Pacific energy

Pacific energy SUPER 27 SPECTRUM Bedienungsanleitung

Avalon

Avalon Olympic 11190 Bedienungsanleitung

Ventis

Ventis HES350 Bedienungsanleitung

IronStrike

IronStrike Striker S160GL Bedienungsanleitung