Nikon NIKKOR Bedienungsanleitung

AF-S NIKKOR 70-200mm f/4G ED VR

Nano Crystal Coat

使用説明書

User’s Manual

Benutzerhandbuch

Manuel d’utilisation

Manual del usuario

Användarhandbok

Pykoводство пользoвaтеля

Gebruikshandleiding

Manual do utilizador

Manual do usuário

Manuale d’uso

Návod k obsluze

Užívateľská príručka

Manualul utilizatorului

Посібник користувача

ҋᅶᢪ೗Ϸ

ᮢ⦦ᆙሬ

⏷⧴⑯󰵱⑧

Manual bagi Pengguna

For Your Safety

CAUTIONS

Do not disassemble.

Touching the internal parts of the camera or lens could

result in injury.

In the event of malfunction, the product should be repaired

only by a qualified technician.

Should the product break open as the result

of a fall or other accident, remove the camera battery and/or disconnect

the AC adapter and then take the product to a Nikon-authorized service

center for inspection.

Turn the camera off immediately in the event of malfunction.

Should you notice

smoke or an unusual smell coming from the equipment, immediately

unplug the AC adapter and remove the camera battery, taking care to

avoid burns.

Continued operation could result in fire or injury.

After

removing the battery, take the equipment to a Nikon-authorized service

center for inspection.

Do not use in the presence of flammable gas.

Operating electronic equipment in

the presence of flammable gas could result in explosion or fire.

Do not look at the sun through the lens or the camera viewfinder.

Viewing the sun

or other bright light source through the lens or viewfinder could cause

permanent visual impairment.

Keep out of reach of children.

Failure to observe this precaution could result in

injury.

Observe the following precautions when handling the lens and camera:

Keep the lens and camera dry.

Failure to observe this precaution could

result in fire or electric shock.

Do not handle the lens or camera with wet hands.

Failure to observe this

precaution could result in electric shock.

Keep the sun well out of the frame when shooting backlit subjects.

Sunlight focused into the camera when the sun is in or close to the frame

could cause a fire.

If the lens will not be used for an extended period, attach the front and

rear lens caps and store the lens out of direct sunlight.

If left in direct

sunlight, the lens could focus the sun’s rays onto flammable objects,

causing fire.

Do not carry tripods with a lens or camera attached.

You could trip or accidentally

strike others, resulting in injury.

Do not leave the lens where it will be exposed to extremely high temperatures, such as

in an enclosed automobile or in direct sunlight.

Failure to observe this precaution

could adversely affect the lens’internal parts, causing fire.

•

Parts of the Lens

!1 !2 !3 !4

rtyu io !0q

!9!8

!6 !7

Optional.

qLens hood mounting mark.......18

wFocus ring ............................................ 15

eFocus distance indicator

rFocus distance mark

tZoom ring............................................15

yFocal length scale...........................15

uFocal length mark

iLens mounting mark

oRubber lens-mount gasket.......20

!0 CPU contacts ..................................... 20

!1 Focus-mode switch.......................15

!2 Focus limit switch...........................15

!3 Vibration reduction ON/OFF

switch ...............................................16

!4 Vibration reduction mode

switch ...............................................16

!5 Lens hood............................................ 18

!6 Lens hood alignment mark ......18

!7 Lens hood lock mark.....................18

!8 Position indices (90°) *.................. 19

!9 Tripod collar ring*..........................19

@0 Tripod collar ring attachment

knob * ............................................... 19

Thank you for your purchase of an AF-S NIKKOR 70-200mm f/4G ED VR

lens.

Before using this product, please carefully read both these

instructions and the camera manual.

Note: When mounted on a DX-format digital single-lens reflex camera such as

the D7000 or cameras in the D300 series, this lens has an angle of view of

22° 50′– 8° and a focal length equivalent to 105– 300 mm (35 mm format).

Compatibility

Check marks (““) indicate supported features, dashes (“—”) features

that are not supported.

Some limitations may apply; see the camera

manual for details.

Camera

Exposure (Shooting) mode

Function

P4 SAMAF

5 VR6

Nikon FX-format and DX-format digital single-lens reflex cameras,

F6, F5, F100, F/N80-series1, F/N75-series1, F/N65-series1 

Pronea 600i/6i1, Pronea S2 

—

F4-series, F90X/N90s1, F90-series/N901, F70-series/N701 ——

—

F60-series/N601, F/N55-series1, F50-series/N501, F-401x/

N50051, F-401s/N4004s1, F-401/N40041 

——

F-801s/N8008s1, F-801/N80081, F-601M/N60001 ————

F3AF, F-601/N60061, F-501/N20203, Nikon manual focus

cameras (excluding F-601M/N60001)—

N-series cameras and Pronea

6i sold in U. S. A. only.

Exposure mode M (manual)

not available.

N2020 sold in U. S. A. and Canada only.

Includes AUTO and scene (Digital Vari-

Program) modes.

Autofocus.

Vibration reduction.

Focus

Supported focus modes are shown in the following table (for information

on camera focus modes, see the camera manual).

Camera

focus mode

Lens focus mode

A/M M

Nikon FX-format and DX-format digital single-lens

reflex cameras, F6, F5, F4-series, F100, F90X/N90s*,

F90-series/N90 *, F/N80-series *, F/N75-series *, F70-

series/N70 *, F/N65-series *, Pronea 600i/6i *, Pronea S

Autofocus with

manual override

(AF priority)

Manual focus

with electronic

rangefinder

MF Manual focus (electronic

rangefinder available with all

cameras except F-601M/

N6000*)

F60-series/N60 *, F/N55-series *, F50-series/N50 *,

F-801s/N8008s *, F-801/N8008 *, F-601M/N6000 *,

F-401x/N5005 *, F-401s/N4004s *, F-401/N4004 *

AF, MF

N-series cameras and Pronea 6i sold in U. S. A. only.

A/M (Autofocus with Manual Override/AF Priority)

To focus using autofocus with manual override (A/M):

zSlide the lens focus-mode switch to A/M.

xFocus.

If desired, autofocus can be over-ridden by rotating the lens focus

ring while the shutter-release button is pressed halfway (or, if the

camera is equipped with an AF-ON button, while the AF-ON button

is pressed); note that the ring must be rotated a short distance before

autofocus is over-ridden.

To refocus using autofocus, press the

shutter-release button halfway or press the AF-ON button again.

The Focus Limit Switch

This switch determines the focus distance limits for autofocus.

FULL: Select this option for subjects that may be closer than

3 m (9.84 ft).

∞–3 m: If your subject will always be at distance of at least

3 m (9.84 ft), select this option for faster focusing.

Zoom and Depth of Field

Before focusing, rotate the zoom ring to adjust the focal length and frame

the photograph.

If the camera offers depth-of-field preview (stop down),

depth of field can be previewed in the viewfinder (see page 210 for more

information).

Note: Note that the focus distance indicator is intended only as a guide and

may not accurately show the distance to the subject and may, due to depth

of field or other factors, not show ∞ when the camera is focused on a distant

object.

Aperture

Aperture is adjusted using camera controls.

Built-in Flash Units

When using the built-in flash on cameras equipped with a built-in flash

unit, remove the lens hood to prevent vignetting (shadows created

where the end of the lens obscures the built-in flash).

Vibration Reduction

Vibration reduction reduces blur caused by camera shake, allowing

shutter speeds up to five stops slower than would otherwise be the case

(Nikon measurements; effects vary with the photographer and shooting

conditions).

This increases the range of shutter speeds available and

permits hand-held, tripod-free photography in a wide range of situations.

Using the Vibration Reduction ON/OFF Switch

Select ON to enable vibration reduction.

Vibration reduction is

activated when the shutter-release button is pressed

halfway, reducing the effects of camera shake for

improved framing and focus.

Select OFF to turn vibration reduction off.

Using the Vibration Reduction Mode Switch

The vibration reduction mode switch is used to select the vibration

reduction mode when vibration reduction is on.

Select NORMAL to reduce the effects of vibration when

photographing from a fixed position and in other

situations with comparatively little camera motion.

Select ACTIVE to reduce the effects of vibration when

shooting from a moving vehicle, while walking, and in

other situations with active camera motion.

Using Vibration Reduction: Notes

Slide the vibration reduction switch to OFF if the camera does not

support vibration reduction (pg. 14).

Leaving vibration reduction on

may greatly increase the drain on the battery, particularly in the case of

Pronea 600i/6i cameras.

When using vibration reduction, press the shutter-release button

halfway and wait for the image in the viewfinder to stabilize before

pressing the shutter-release button the rest of the way down.

When vibration reduction is active, the image in the viewfinder may be

blurred after the shutter is released.

This does not indicate a

malfunction.

Slide the vibration reduction mode switch to NORMAL for panning

shots. When the camera is panned, vibration reduction applies only to

motion that is not part of the pan (if the camera is panned horizontally,

for example, vibration reduction will be applied only to vertical shake),

making it much easier to pan the camera smoothly in a wide arc.

Do not turn the camera off or remove the lens while vibration reduction

is in effect.

If power to the lens is cut while vibration reduction is on, the

lens may rattle when shaken.

This is not a malfunction, and can be

corrected by reattaching the lens and turning the camera on.

If the camera is equipped with a built-in flash, vibration reduction will

be disabled while the flash charges.

Turn vibration reduction off when the camera is securely mounted on a

tripod, but leave it on if the tripod head is not secured or when using a

monopod.

•

The Lens Hood

The lens hoods protect the lens and block stray light that would

otherwise cause flare or ghosting.

Align the lens hood lock mark (—) with the

lens hood mounting mark (L) on the lens (e).

When attaching or removing the hood, hold it near the symbol on its

base and avoid gripping it too tightly.

Vignetting may occur if the hood is

not correctly attached.

The hood can be reversed and mounted on the lens when not in use.

When the hood is reversed, it can be attached and removed by rotating it

while holding it near the lock mark (—).

Focusing Screens

The following cameras support a variety of focusing screens for use in

different situations.

Screen

Camera A B C E EC-B

EC-E G1 G2 G3 G4 J L M U

F6 

—————— 

F5+DP-30    

(+0.5)  

F5+DA-30 

(+1.0)



(+0.5) 

(+0.5) 

(–1.0)



(+0.5)



(+1.0) 

: Recommended.

: Vignetting visible in viewfinder (photographs are not affected).

—: Not compatible with camera.

( ): Figures in parentheses give the exposure compensation for center-

weighted metering.

Select “Other screen” for Custom Setting b6

(“Screen comp.”) when adjusting exposure compensation for the F6;

note that with screens other than B or E, “Other screen” must be

selected even when the value for exposure compensation is 0.

Exposure compensation for the F5 can be adjusted using Custom

Setting 18; see the camera manual for details.

Empty cell: Not suited to use with this lens.

Note that type M screens can

however be used for photomicrography and macro photography at

magnifications of 1 : 1 or higher.

Note: The F5 supports matrix metering with A, B, E, EC-B/EC-E, J, and L

focusing screens only.

The Optional RT-1 Tripod Collar Ring

Loosen the tripod collar ring attachment knob to rotate the camera to the

desired position and orient the display horizontally or vertically. Note that

your hand may come into contact with the tripod if you rotate the camera

while holding it by the handgrip. Depending on how the camera or

tripod is attached, camera shake may be reduced by attaching the tripod

to the camera tripod mount.

WARNING

Fully tighten the tripod collar ring attachment knob when attaching

tripod collar ring.

Failure to observe this precaution could result in the

tripod collar ring becoming detached from the lens, causing injury.

Attaching the Tripod Collar Ring

zLoosen the tripod collar ring attachment knob

(q).

xOpen the ring.

Pull the attachment knob toward you (w) and

open the ring (e).

cPlace the lens in the ring (r).

vClose the ring.

Pull the attachment knob toward you (t) and close

the ring (y).

Do not use excessive force, as your

hand could be caught in the ring.

bTighten the attachment knob (u).

Positioning the Camera

Loosen the attachment knob (q), adjust the position

indices to the desired vertical or horizontal orientation

(w), and then tighten the attachment knob (e).

Removing the Tripod Collar Ring

4zLoosen the attachment knob (q).

xRemove the ring.

Pulling the attachment knob toward you (w), open

(e) and remove the lens (r).

Lens Care

Do not pick up or hold the lens or camera using only the lens hood.

Keep the CPU contacts clean.

Should the rubber lens-mount gasket be damaged, cease use

immediately and take the lens to a Nikon-authorized service center for

repair.

Use a blower to remove dust and lint from the lens surfaces.

To remove

smudges and fingerprints, apply a small amount of ethanol or lens

cleaner to a soft, clean cotton cloth or lens-cleaning tissue and clean

from the center outwards using a circular motion, taking care not to

leave smears or touch the glass with your fingers.

Never use organic solvents such as paint thinner or benzene to clean

the lens.

The lens hood or NC filters can be used to protect the front lens

element.

Attach the front and rear caps before placing the lens in its flexible

pouch.

If the lens will not be used for an extended period, store it in a cool, dry

location to prevent mold and rust.

Do not store in direct sunlight or

with naphtha or camphor moth balls.

Keep the lens dry.

Rusting of the internal mechanism can cause

irreparable damage.

Leaving the lens in extremely hot locations could damage or warp parts

made from reinforced plastic.

Supplied Accessories

67 mm snap-on Front Lens Cap LC-67

Rear Lens Cap LF-4

Bayonet Hood HB-60

Flexible Lens Pouch CL-1225

Compatible Accessories

67 mm screw-on filters

Tripod collar ring RT-1

AF-I/AF-S Teleconverters TC-14E/TC-14E II/TC-17E II */TC-20E */

TC-20E II */TC-20E III *

Autofocus is available only with cameras that offer f/8 support.

•

Andere Handbücher für NIKKOR

Inhaltsverzeichnis

Andere Nikon Kameraobjektiv Handbücher

Nikon

Nikon AF-S Nikkor 300mm f/2.8G ED VR II Bedienungsanleitung

Nikon

Nikon 24mm F/1.4G ED AF-S Nikkor Bedienungsanleitung

Nikon

Nikon AF-S VR Zoom-Nikkor 200-400mm f/4G IF-ED Bedienungsanleitung

Nikon

Nikon AF-S DX NIKKOR 35mm f/1.8G Bedienungsanleitung

Nikon

Nikon AI-S Zoom-Nikkor 200-600mm f/9.5 Bedienungsanleitung

Nikon

Nikon AF-S NIKKOR 24-70mm f/2.8G ED Bedienungsanleitung

Nikon

Nikon AF Micro-Nikkor 60mm F/2.8 D Bedienungsanleitung

Nikon

Nikon NIKKOR Z 14-30mm f/4 S Bedienungsanleitung

Nikon

Nikon AF Micro-Nikkor 60 mm f/2.8D Bedienungsanleitung

Nikon

Nikon f/2 D Bedienungsanleitung

Nikon

Nikon DS-Ri2 Bedienungsanleitung

Nikon

Nikon PC-E Bedienungsanleitung

Nikon

Nikon AF-S VR Zoom-Nikkor 70-300mm f/4.5-5.6G... Bedienungsanleitung

Nikon

Nikon 24mm F/1.4G ED AF-S Nikkor Bedienungsanleitung

Nikon

Nikon D5000 Bedienungsanleitung

Nikon

Nikon AI-S Zoom-NIKKOR ED 200-400mm f/4 Bedienungsanleitung

Nikon

Nikon NIKKOR Z 70-200mm f/2.8 VR S Bedienungsanleitung

Nikon

Nikon AF-S NIKKOR 200mm f/2G ED VR II Bedienungsanleitung

Nikon

Nikon JAA78351 Betriebsanleitung

Nikon

Nikon AF-I Nikkor ED 300mm f/2.8D IF Bedienungsanleitung

Nikon

Nikon NIKKOR Z 400mm f/2.8 TC VRS Bedienungsanleitung

Nikon

Nikon PC NIKKOR 19mm f/4E ED Bedienungsanleitung

Nikon

Nikon Nikkor ASF200 Bedienungsanleitung

Nikon

Nikon NIKKOR Bedienungsanleitung

Beliebte Kameraobjektiv Handbücher anderer Marken

THORLABS

THORLABS ELL15 Bedienungsanleitung

FUJICA

FUJICA ZC1000 Bedienungsanleitung

Tamron

Tamron A09 Handbuch

Sony

Sony SEL-55210 Bedienungsanleitung

Sony

Sony VCL-HG2037 Bedienungsanleitung

Honeywell

Honeywell HLM25V6F12 Bedienungsanleitung

Sony

Sony VCL-ST30 Bedienungsanleitung

Canon

Canon FD 35 - 70 mm Bedienungsanleitung

Sony

Sony SAL-85F14Z - 85mm f1.4 Carl Zeiss Planar T Coated Telephoto... Bedienungsanleitung

ARRI

ARRI Lenses Bedienungsanleitung

Panasonic

Panasonic LUMIX G X Vario 45-175mm f/4.0-5.6 Bedienungsanleitung

Rokinon

Rokinon DS50M-C Bedienungsanleitung

Olympus

Olympus M.Zuiko Digital ES 300mm f4.0 IS PRO Bedienungsanleitung

Sony

Sony VCL-DE07T Bedienungsanleitung

Canon

Canon FD Lens Handbuch

Tamron

Tamron A036 Bedienungsanleitung

Samsung

Samsung 20-50mm F3.5-5.6 ED II Bedienungsanleitung

Tamron

Tamron 272E Bedienungsanleitung