Nikon DTM-502 Series Bedienungsanleitung

H162 E 02.10.VF.2

Total Station DTM-502 series

DTM-552

DTM-532

DTM-522

Instruction Manual

1 NOMENCLATURE

1-1

NOMENCLATURE

Carrying-handle

battery BC-80

Telescope focusing ring

Telescope eyepiece

Diopter ring

Plate level

Display

Face-left keyboard

Storage mark

Leveling base

clamp knob

Refer to p.3-1 ~ p.3-3 for

the key arrangement and

its major function.

Battery mounting

buttons

Main body/Battery

aligning mark

Upper plate

tangent screw

Upper plate clamp

Vertical tangent screw

Vertical clamp

1-2

NOMENCLATURE

Optical sight (Finder)

Lumi-guide transmitter

Objective

Face-right keyboard

Leveling base

Holizontal axis

indication mark

Optical plummet

Data output/External

power input connector

Circular level

Base plate Leveling screw

Input voltage

DC 7.2 – 11V

NOMENCLATURE

This page is intentionally left blank.

Thank you for purchasing the Nikon products. This

instruction manual was written for the users of the

Electronic Total Station DTM-502 series. To ensure

correct usage read this manual carefully before

operating the instrument.

Also read the Instruction Manual provided with the

Battery Charger and any other equipments used

together with the DTM-502 series.

Warning and Caution

Symbols in This Manual

Though Nikon products are designed to provide you

utmost safety during use, incorrect usage or disregard of

the instructions can cause personal injury or property

damage. For your safety, read the instruction manual

carefully and thoroughly before usage. Do not discard

this manual but keep it near the product for easy

reference.

Inside this instruction manual, safety instructions are

indicated with the symbols shown below. Be sure to

follow the instructions marked with these symbols for

your safety.

WARNING

Disregarding instructions marked with this symbol

may lead to death or serious injury.

CAUTION

Disregarding instructions marked with this symbol

may lead to injury or property damage.

WARNING AND CAUTION

Read This Section Before Use!

WARNING

 Never see the sun through the telescope. Doing so may cause

the loss of your eyesight.

 The DTM-502 does not feature explosion-protected construction.

Do not use in coal mines, in areas contaminated with coal dust, or

near other flammable substances.

 Never disassemble, modify or repair the instrument. Doing so

may cause fire, electric shock or burn.

 Use only the specified charger Q-75U/E for charging the battery

pack BC-80. Charging by the other types of chargers than

specified may cause fire or rupture. (BC-80 can not be charged

by using the charger Q-7U/E or Q7C.)

 While recharging the battery pack, do not cover the charger with

any blanket or clothing which can cause overheating. Make sure

the charger is able to dissipate heat adequately.

 Avoid recharging in humid or dusty places, in direct sunlight, and

near heaters. Do not recharge when wet. Doing so may cause

electric shock, overheating or fire.

 Although the battery pack BC-80 is equipped with an auto-reset

circuit breaker, care should be taken not to short the contacts.

Shorting may cause fire or burn.

 Never burn or heat the battery. Doing so may cause rupture or

injury.

 When storing the battery pack or charger, guard against a short

circuit by putting the insulating tape on the contact point or by doing

some other methods. Failure to do so may result in a short circuit,

causing a fire, burn or instrument damage.

WARNING AND CAUTION

Read This Section Before Use!

CAUTION

 The top of the tripod ferrule is very sharp and may injure your body.

Be careful in handling or carrying the tripod.

 Check the shoulder strap and its clasp before carrying the tripod or

the instrument encased in the carrying case. Damaged strap or

imperfect clasping may cause an accident of falling.

 Before setting up the tripod, check below to make sure no one’s

hands or feet are in the way. Failure to do so may result in injury if

hands or feet should be pierced by the legs of the tripod.

 Fasten firmly the thumb screws of the tripod legs after mounting the

instrument on the tripod. If not, the tripod may collapse, resulting

in injury or instrument damage.

 Be sure to fasten the clamp screw on the tripod securely after

installing the instrument on the tripod. Failure to do this may

cause the instrument to fall, resulting in injury or instrument

damage.

 Fasten securely the leveling base clamp knob. If the knob is not

securely fastened, the leveling base may fall when you grasp the

carrying handle battery, resulting in injury or instrument damage.

 Roughly moving the instrument by grasping the carrying handle

battery without first placing the battery mounting buttons in the

LOCK position may cause the main unit to come loose and fall,

resulting in injury or instrument damage. Make sure that the

battery pack is clamped securely in place and the mounting buttons

are set in the LOCK position.

 Do not stack up the plastic carrying case and do not use it as a

stool. Plastic carrying case is slippery and unstable. Doing

things like this may cause an accident and result in personal injury

or instrument damage.

 Do not swing or throw the plumb bob. It may hit and injure the

other person.

 Be sure to read the instructions of Quick Charger Q-75U/E before

starting charging operation.

iii

MAINTENANCE

Read This Section Before Use!

 Avoid prolonged exposure to the sun or the heat of a closed vehicle.

Efficiency could be adversely affected.

 If the DTM-502 has been used in wet conditions, immediately wipe

off any moisture and dry it completely before replacing it in its

carrying case. The DTM-502 contains many sensitive electronic

assemblies which have been well protected against dust and

moisture. However, should dust or moisture be introduced into the

instrument, severe damage could result.

 Sudden changes in temperature may cloud the lenses and

drastically reduce the measurable distance, or initiate an electrical

system failure. Should this occur, leave the instrument in a warm

location with the case closed until the temperature of the instrument

returns to room temperature.

 Avoid storing the DTM-502 in hot humid locations. Especially, the

battery pack should be stored in a dry location at a temperature of

less than 30°C. Higher temperature and excessive humidity may

result in growth of mold on the lenses and deterioration of the

electronic assemblies, leading to instrument failure.

 Store the battery pack with the battery discharged.

 When storing the instrument in areas subject to extremely low

temperature, leave the carrying case open.

 Do not overtighten any of the clamp screws.

 When adjusting the vertical and upper plate tangent screws or the

leveling screws, stay as close as possible to the center of the

screw’s range, as indicated by a line on the screw.

Use a clockwise rotation of the tangent screws for final adjustment.

 If the leveling base is to be left unused for an extended period,

lock-down the leveling base clamp knob and tighten its safety

screw.

MAINTENANCE Read This Section Before Use!

 Do not use organic solvents (such as ether or paint thinner) to

clean the non-metallic parts such as the keyboard, and the painted

or printed surfaces. Doing so could result in discoloration or in the

peeling of printed characters. Clean only with a soft cloth or tissue

lightly moistened with water or mild detergent.

 Optical lenses may be cleaned by lightly wiping them with a soft

cloth or lens tissue moistened with alcohol.

 Do not leave the carrying case exposed to rain for an extended

period of time, though it is designed to be watertight. If you

expose the carrying case to rain because of unavoidable

circumstances, place it with its “Nikon” nameplate upward.

 The BC-80 battery pack holds Ni-MH inside. Be sure to follow the

laws or rules of your municipal waste system when disposing of it.

2. PREPARATION

2-1

PREPARATION

2-1. Unpacking and Packing the DTM-502

NOTE •Handle gently the DTM-502 to guard against shocks or excessive

vibration.

•Encase the instrument with the battery pack attached.

•When packing the charger Q-75U/E in the plastic carrying case, make

sure the storing position referring to the sticker inside of the case. Be

careful not to pinch the cable of the charger when closing the case

cover.

1) Unpacking

Hold the carrying-handle and take the

instrument out of the case. The instrument

is placed in its carrying case as shown in the

figure.

2) Packing

Set the telescope in the horizontal “face-left”

position and align the storage mark () on

the bottom of the face-left keyboard and the

mark ( ) on the leveling base clamp knob.

Fasten lightly the clamp knobs and then

replace the instrument in its case.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Nikon Messgerät Handbücher

Nikon

Nikon Retinomax Bedienungsanleitung

Nikon

Nikon XF Series Bedienungsanleitung

Nikon

Nikon Prostaff 7i Bedienungsanleitung

Nikon

Nikon COOLSHOT LITE Bedienungsanleitung

Nikon

Nikon COOLSHOT 20 GII Bedienungsanleitung

Nikon

Nikon N Series Bedienungsanleitung

Nikon

Nikon LASER 50 Bedienungsanleitung

Nikon

Nikon NPL-632 Bedienungsanleitung

Nikon

Nikon MONARCH 2000 Bedienungsanleitung

Nikon

Nikon Callaway iQ Bedienungsanleitung

Nikon

Nikon Coolshot 40i Bedienungsanleitung

Nikon

Nikon MONARCH 3000 STABILIZED Bedienungsanleitung

Nikon

Nikon Laser 800 - Monarch Laser 800 Rangefinder Bedienungsanleitung

Nikon

Nikon ARROW ID 3000 Bedienungsanleitung

Nikon

Nikon COOLSHOT 20 GII Bedienungsanleitung

Nikon

Nikon Aculon Bedienungsanleitung

Nikon

Nikon RifleHunter 550 Bedienungsanleitung

Nikon

Nikon Callaway RAZR Bedienungsanleitung

Nikon

Nikon Black Range X 4K Bedienungsanleitung

Nikon

Nikon LASER 30 Bedienungsanleitung

Nikon

Nikon NR-5500 Betriebsanleitung

Nikon

Nikon COOLSHOT Bedienungsanleitung

Nikon

Nikon Laser 550 Bedienungsanleitung

Nikon

Nikon Prostaff 1000i Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung