Nilfisk-Advance APC 328 Bedienungsanleitung

APC 328

INSTRUCTIONS FOR USE-ORIGINAL INSTRUCTIONS

AND PARTS LIST

5/10 revise 7/10

FORM NO. 56041948

Models: 600303281, 600303282

2- FORM NO. 56041948 - APC 328

IMPORTANT SAFETY INSTRUCTIONS

This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops, and ofﬁces other than

normal residential housekeeping purposes.

When using any electrical appliance, basic precautions should always be followed, including the following:

WARNING!

To reduce the risk of ﬁre, electric shock, or injury:

•Do not leave the machine unattended when it is plugged-in. Unplug the unit from the power outlet when not in use.

• Always use a defoamer when foaming occurs to prevent damage to vacuum motor(s).

•Unplug the machine from the power outlet before cleaning or servicing.

•To avoid electric shock, do not expose to rain or snow. Store, and use, indoors.

•Wear hearing protection if desired.

•Do not allow to be used as a toy. Close attention is necessary when used near children.

•Use only the manufacturer’s recommended attachments.

•Inspect the power cord regularly for damage, such as cracking, ageing, or damaged insulation. Replace the power cord with the

same type as original if any damage is found. Do not use with damaged cord or plug.

• Use approved chemicals only. Never use solvents.

• Do not let the pump run dry.

•If the machine is not working as it should, has been dropped, damaged, left outdoors or ﬂooded with water, return it to a service

center.

•Do not pull the machine by the cord, do not use the cord as a handle, close a door on the cord, or pull the cord around sharp

edges or corners. Do not run the machine over the cord. Keep the cord away from heated surfaces. To unplug, grasp the plug,

not the cord.

•Extension cords must be 12 gauge and no longer than 15 m. Replace the cord or unplug immediately if the ground prong

becomes damaged.

• Never ﬁll the tank with water above 54ºC.

•Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may

reduce air ﬂow.

•Keep loose clothing, hair, ﬁngers, and all parts of body away from openings and moving parts.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes, or any health endangering dusts.

Do not use to pick up ﬂammable or combustible liquids such as gasoline or use in areas where they may be present.

•Turn off all controls before unplugging.

•Use extra care when cleaning on stairs.

•Liquid ejected at the spray nozzle could be dangerous as a result of its temperature, pressure,or chemical content.

SAVE THESE INSTRUCTIONS

FORM NO. 56041948 - APC 328 - 3

INSPECTION:

Carefully unpack and inspect your APC 328 for shipping damage. Each machine is tested and inspected before shipping. Any shipping damage

incurred is the responsibility of the carrier. You should notify the carrier immediately if you notice damage to the box or to the machine or parts.

CLEANING SOLUTIONS:

We recommend liquid cleaning chemicals. Powder chemicals may be used, but unless mixed very thoroughly they could cause a build-up in the

pump, lines, heat exchanger and/or quick disconnects. Any problem caused by a chemical build-up is not covered by warranty. Use a neutral

cleaner with a pH between 5 and 10 to avoid premature wear of the pump, seals, and/or other components.

MAINTENANCE:

For optimum performance ﬂush the machine with clear water at the end of each working day. Once a month, minimum, run a ﬂushing compound

through the machine to break up any mineral or chemical build-up that may have formed. The vacuum motor and the pump do not require any

scheduled maintenance; however, the motor may require replacement brushes after 1000 - 1500 hours. Clean the body with an all-purpose

detergent, and protect it with an automobile interior polish. Lubricate the wheels, castors, and quick disconnects with an all purpose silicone

spray. Refer to the maintenance schedule on page 9.

PARTS AND SERVICE:

Repairs, when required, should be performed by your authorized distributor who maintains an inventory of original replacement parts and

accessories. Call the distributor from whom you purchased this machine if you need parts and service. Be sure to specify the machine model.

Have your serial number at hand.

Serial Number: __________________ Model: APC 328

Purchase Date:_____________

Write the name and phone number of your distributor:

____________________________________________________________________

Be sure to register your purchase to activate your warranty

4- FORM NO. 56041948 - APC 328

KNOW YOUR MACHINE

Operator Handle (1): Operator holds onto this handle to move the machine from one location to another.

Solution Tank Lid (2): This lid screws off so the tank can be ﬁlled. The solution ﬁll hose is tethered to the lid, and hangs inside the arm of the

Operator Handle.

Maid’s tote and Recovery tank lid (3): This removable container holds often-used items and has a handle for easy carrying. The recovery

tank lid sits under the maid’s tote and covers the opening in the Recovery Tank. This is where the operator can access the tank to clean it

and the ball ﬂoat cage. The tank can be ﬂushed out by running clean warm water into this opening and laying the open drain hose into a

bucket or drain.

Recovery Hose (4): Waste water is picked-up through this hose.

Spray Hose (5): This hose delivers water from the machine to the cleaning tool.

Drain Hose (6): This hose is used to empty the recovery tank. NOTE: hold the end of the hose above the water level in the tank to avoid

sudden, uncontrolled ﬂow of waste water when you remove the cap, then lower the hose slowly to control the rate of discharge.

Quick Disconnect (7): Point of attachment for the Spray Hose (5).

Castors and Wheels (8): Castors pivot for ease of steering, and large back wheels make it easy to roll the machine from location to

location.

Chemical Feed Lines (9): These clear tubes connect the cleaning chemical containers to the machine where the chemical can be

siphoned into the outlet water from the pump. Metering tips -- used to change the ratio of water to chemical -- are installed here.

Switch Plate (10): The machine’s on/off switches for the vacuum and for the pump are located here and this is where the valve to change

chemical feeds is located.

Power Cord (11): The 25 ft. power cord connects to a power cord pigtail on the rear of the machine.

Chemical Container Holders (12): Two molded-in bottle holders for chemical jugs.

FORM NO. 56041948 - APC 328 - 5

COLOR HOLE SIZE MIX RATION FLOW RATE

Orange 0.007 1 to 128 7,81 ml per 1 l

Pink 0.012 1 to 64 19,53 ml per 1 l

Dark Green 0.014 1 to 50 23,44 ml per 1 l

Yellow 0.016 1 to 32 39,06 ml per 1 l

Light Blue 0.020 1 to 20 46,87 ml per 1 l

Burgandy 0.022 1 to 15 70,33 ml per 1 l

Black 0.048 1 to 5 156,27 ml per 1 l

METERING TIPS

KNOW YOUR SWITCH PLATE

Vacuum Switch (1): turns on the vacuum motor.

Chemical Valve (2): switches between the two chemical containers. When the selector is pointed straight down, the valve is off and neither

chemical is selected. When the selector is pointed directly towards one or the other symbols, that chemical is selected.

Solution Pump Switch (3): turns on the solution pump.

Quick Connect (4): this is where solution comes out of the machine and the attachment point for the solution hose.

METERING TIPS

The chemical metering tips allow you to select the ratio of chemical to water, as the water ﬂows out of the machine. Insert the correct metering tip

for the desired mixture into the chemical siphon tube.

6- FORM NO. 56041948 - APC 328

SET-UP AND USE

1) Insert the appropriate metering tips into the chemical feed lines (see illustration, page 5).

2) Fill the holding tank with warm water (not exceeding 54 °C). Do not add any chemical to the tank.

3) Prepare the area for cleaning by emptying waste receptacles, clearing debris, removing paper products, blowing out vents, and sweeping

ﬂoors.

4) Connect the 25 ft power cord to the pig-tail on the rear of the machine.

5) PRIME THE PUMP: Attach the priming hose to the outlet quick disconnect and place the open end of the hose into the recovery tank. Turn

on the pump and let it run until the pump is completely primed (no visible air in the water stream). Turn the pump off.

NOTE: prime the machine before you place the chemical feed tubes into chemical containers.

6) Disconnect the priming hose and attach the solution hose to the quick disconnect.

7) Attach the spray gun to the other end of the solution line.

8) Place chemicals in the molded-in chemical bottle containers on the rear of the machine. Insert one of the feed lines into one of the chemical

containers. Secure the line by screwing on the cap. The chemical will feed from which ever container the selector valve on the switch plate is

turned towards and when the gun is used in the low pressure setting. Use chemicals with a pH of between 5 and 10. Never add chemicals to

the clean water tank.

9) Set the spray gun to low pressure by sliding the pressure selector forward (low pressure = forward; high pressure = back).

10) Turn on the pump switch (push button) and spray through the gun for a few seconds to ﬁll the line with solution.

11) Apply the chemical to the walls and ﬁxtures from the bottom up. Spray the ﬂoor last as you work your way out of the room.

12) Allow the chemical to work for the proper amount of dwell time, according to the chemical manufacturer’s directions. Agitate heavily soiled

areas with a scrub brush.

13) Turn off the chemical injector valve by turning the selector to the down position.

14) Set the spray gun to high pressure and rinse the area from the top down.

15) Connect the vacuum hose, attach the squeegee, and turn on the vacuum (rocker switch).

16) Squeegee off the mirrors, pick up the liquid off the ﬂoor with the ﬂoor tool. If you have the optional blow dry hose, use it to dry the ﬁxtures.

17) Drain the recovered water into a utility sink or toilet. NOTE: Keep the top of the drain hose higher than the water level in the tank to avoid

uncontrolled discharge of water when you open the cap on the hose.

CAUTION

To avoid vacuum motor damage, always use a defoamer any time foam is present.

Before you turn on the vacuum always make sure the ﬁlter screen on the ball ﬂoat is clean and that the ball can travel freely.

RE-PRIMING THE PUMP

If the pump looses prime between jobs, follow the instructions to PRIME THE PUMP, above. If that doesn’t get water ﬂowing, put the priming hose

into the vacuum inlet hose barb and cover the rest of the space around the priming hose with your hand. Turn on the vacuum (with the pump also

running) and let the suction of the vacuum assist in getting water into the pump.

FORM NO. 56041948 - APC 328 - 7

MAINTENANCE

1) Use only approved chemicals at the recommended mix ratios. All chemicals should be added through the feed system and NOT added

directly to the water in the solution tank to prevent possible damage to the pump, seals, or other components.

2) For optimum performance, ﬂush the Chemical Feed lines after every job by replacing the chemical containers with containers of clear water

and spraying through the gun until the ﬂuid stream is clear. See the Maintenance Schedule, below.

3) The pump seals and/or valves in the high pressure pumps may need to be replaced after about 1000 hours of use, if the pump begins to lose

performance or to leak. The pressure regulator valve may need to be when a drop in the spraying pressure at the tool is apparent.

MAINTENANCE SCHEDULE

ITEM DAILY WEEKLY YEARLY

Flush chemical lines X

Check/clean vac inlet ﬁlter X

Clean solution ﬁlter X

Check vacuum motor airways X

Check pump for leaks X

Check vacuum motor brushes * X

* Have your distributor check the carbon brushes once a year or after about 500 hours of operation.

TECHNICAL SPECIFICATIONS (as installed and tested on the unit)

MODELS 600303281, 600303282

VACUUM MOTOR(s): Two stage, 8 Amp

WATER LIFT: 23 kpa

AIR FLOW: 100 CFM

TANK CONSTRUCTION: Rotationally molded polyethylene

HEIGHT: 98 cm X 59 X 86.5 cm

WEIGHT 50 KG

8- FORM NO. 56041948 - APC 328

APC 328

01-11-09

11 12 13

16A

17A

FORM NO. 56041948 - APC 328 - 9

ITEM PART No. DESCRIPTION

1 600732869 Lid and gasket, recovery tank

2 600732846 Hose kit, drain, priming and vac inlet

3 600732882 Hose kit, water and chemical metering

4 600732871 Metering tips and chemical injector

5 600732889 Filter, electrical noise suppression

6 600732883 Vacuum motor kit, with gasket and hose

7 600732884 Tank, recovery, complete

8 600732874 Vacuum inlet kit

9 600732886 Switch plate kit, complete

10 600732885 Switch kit, two switches

11 600732876 Pallet, component mounting, complete

12 600732848 Lid, with ﬁll hose, holding tank/base

13 600732858 Fasteners kit

14 600732856 Lid and ring, 4”

15 600732873 Power cord, EU

600732887 Power cord, UK

16 600732866 Pump and motor, complete

16A 600732868 Motor, pump drive

17 600732865 Pump, solution, complete, no motor

17A 600732875 Pressure regulator, for solution pump

18 600732877 Filter, pump in-line, with hoses

19 600732854 Vacuum recovery hose, complete, 8 M

20 600732855 Solution hose assembly, 8 M

21 600732847 Quick disconnect kit, with washers

22 600732859 Grommets and foam

23 600732849 Cap, drain, and brass ﬁtting

24 600732850 Castor kit, includes bracket

25 600732852 Wheel kit

26 600732879 Holding tank/base, complete

MISCELLANEOUS PARTS

600732872 Label kit, APC 328

600732888 Repair kit, solution pump

10 - FORM NO. 56041948 - APC 328

245

TOOLS AND ACCESSORIES

Tool kit, standard, complete

1 600732862 Squeegee, hand held

2 600732893 Handle, for hand held squeegee

3 600732855 Solution hose

4 600732863 Brush, dual surface

5 600732894 Handle, two piece

6 600732895 Squeegee, for ﬂoor

7 600732896 Gun, spray, dual pressure

8 600732860 Handle, straight, black

9 600732881 Tote, carry all

10 600732853 Metering tips, two each

11 600752127 Priming hose, for solution pump

12 600732854 Recovery hose

Optional accessories

1 600732897 Frame, micro ﬁber mop

2 600732898 Mop, micro ﬁber (6)

3 56380888 Squeegee assembly, 61 cm

4 56209089 Squeegee assembly, 76 cm

5 600732901 Mount assembly, mechanical, for squeegee heads

6 600732864 Blower hose assembly, with nozzle

123 or 4

Andere Handbücher für APC 328

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Nilfisk-Advance Hochdruckreiniger Handbücher

Nilfisk-Advance

Nilfisk-Advance MH 5M Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance MC 2C Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance MC 5M Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance P 130.2 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance C 120.4 Betriebsanleitung

Nilfisk-Advance

Nilfisk-Advance MH 5M E Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance FI-30N Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance MC 2C Series Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance MH 3M Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance MC 4M Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance ALPHA BOOSTER 3 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance 2300A Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance N/G-4001A Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance P 130.1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance NEPTUNE 4 FA Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance P 150.2 X-TRA Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance C 125.4 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Gerni 2302A Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SC UNO 4M 140/620 PS Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Nilfisk C 120.3 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Excellent 160 Betriebsanleitung

Nilfisk-Advance

Nilfisk-Advance N/G-6900A/C Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Core 150 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance C 100.6 Bedienungsanleitung

Beliebte Hochdruckreiniger Handbücher anderer Marken

Shark

Shark RG-232637 Bedienungsanleitung

Shakti Technology

Shakti Technology S3 Bedienungsanleitung

Kärcher

Kärcher K 4 Pure Bedienungsanleitung

Porter-Cable

Porter-Cable D25806-025-2 Bedienungsanleitung

REM POWER

REM POWER HDEm 662 Bedienungsanleitung

Landa

Landa HS-3000 Bedienungsanleitung

Craftsman

Craftsman 580.752270 Bedienungsanleitung

HIKOKI

HIKOKI AW 100 Bedienungsanleitung

Delco

Delco DC 1302 Bedienungsanleitung

Kärcher

Kärcher K 3 Full Control Bedienungsanleitung

BIEMMEDUE

BIEMMEDUE 120/10 - 170/13 Bedienungsanleitung

ARKSEN

ARKSEN 014-HG-14141-HR Bedienungsanleitung

Black & Decker

Black & Decker PW1700SPX Bedienungsanleitung

Kärcher

Kärcher 595 - SPARE Leitfaden

Kranzle

Kranzle B 10 200 Bedienungsanleitung

Stihl

Stihl RE 90 Bedienungsanleitung

PowR-Quip

PowR-Quip PQ-2600 Bedienungsanleitung

Hotsy

Hotsy 5645 Bedienungsanleitung