Nivel System NL410 Bedienungsanleitung

Thank you for purchasing a Nivel System NL410 / NL410G laser level.

To best use the purchased instrument, please read the instructions carefully and put in a

convenient spot so that in the future you will be able to use it.

INTRODUCTION

Multitasking self-leveling laser construction levels are used to determine the height in

construction measurements. Model NL410 / NL410G has a visible light beam (NL410 - red

beam, NL410G - green beam) and it can be used at work inside and outside the building. The

device is powered by rechargeable batteries which use advanced micro-controlled charging

technology.

NL series levels may designate a vertical or horizontal laser plane, additionally the device define

the axis of the laser plane (laser line - point up and down). The device can also "draw" a laser

line (scan function) –thanks to it it's possible to stop the beam at a given distance. NL410 /

NL410G models can be controlled from the device control panel or remotely, with remote

control.

Laser level is waterproof and can be used outdoors, even in the rain. However, these devices

can’t be submerged in water

The laser plummet (top)

Rotating head

Windows which security

laser heads

Control panel

AC input

Rechargeable battery

pack

The laser plummet (bottom) Tripod adapter (vertical set up)

PRECAUTIONS

WARNING: the device has a built in laser source which generates laser beam. It Is not allowed

to disassembly the device by "your own".

There is a risk of fire, electric shock, or injury while self-repair.

Repairs can be made only by Nivel System service or its authorized representatives.

The laser beam can be hazardous to the human eye if the device is improperly operated.

Never repair the laser by your own.

Protect your eyes from damage.

Never look into the laser beam

Risk of fire and electric shock.

Never use a wet battery.

The possibility of explosion.

Never use a laser level near flammable gases and liquids.

A short-circuit may cause a fire.

Pay attention to not to short-circuit the battery while storing the device.

Protection against shock

When transporting the instrument it should be protected against shocks. Strong shocks can

cause measurements errors.

The user of this instrument should follow the instructions contained in this manual and

remember to periodically check the correctness of its working. The manufacturer is not liable for

any damage resulting from the incorrect use of the instrument and losses due to this.

Improper use of the laser and use not in accordance with instructions described in this manual,

can cause injury or exposure to excessive radiation dose.

Do not allow anyone to work in a laser beam. Before you begin, make sure that the laser beam

is over the heads of workers. The lighting by laser beam can cause temporary blindness. When

it's possible, use warning signs when construction machines are working near laser level

Do not expose the body and clothing to the acid leaking from batteries and accumulators.

However, if it occurs, quickly wash the body with clean water and consult a doctor.

Broken or damaged transport box or transport box latches can lead to falling out of the box and

damage the laser.

The collapse of laser level to the ground can lead to damage.

Shaky, unstable site of laser level can lead to collapse and damage the laser. Always make

sure that all screws and latches in a tripod works properly.

Exclusions of liability

1. It is expected from the user to comply all recommendations regarding to the use of this

product and perform periodic reviews of the work of the instrument.

2. The manufacturer, or its representatives assume no liability for damages caused by

improper handling or intentional improper use , including direct or indirect damage and

loss of income.

3. The manufacturer and its representatives are not liable for damage or loss of income

caused by natural disasters (earthquake, storm, flood, etc.), Fire, accident or involving

third parties in use of this instrument or using the instrument under conditions other than

normal.

4. The manufacturer and its representatives are not liable for any damages, loss of income,

loss of data, interruption of business, etc.., Caused by the use of the product.

5. The manufacturer and its representatives are not liable for any damages and loss of

income caused by the use of the instrument in a way other than described in the manual.

6. The manufacturer and its representatives are not liable for damage caused by improper

activities or reactions as a result of combining with other products.

TAKE CARE OF THE EQUIPMENT!

Never put a wet instrument in the case, wipe it with a cloth and dry it earlier. Although the

equipment is waterproof, storing the wet equipment in the case may affect the condition of the

equipment (eg the elements inside may corrode).

BATTERIES

The NL410 / NL410G used nickel-hydrogen batteries that can be recharged.

Charging the battery is done by the AC adapter (included in standard) - Use the connector on

the front panel of laser level.

Charging process is indicated by illumination of the LED. When the LED lights up green, the

charging process is completed.

Never use alkaline batteries to power the NL410 / NL410G

If it's necessary to replace the battery - battery compartment should be unscrewed with a

screwdriver. Replacement batteries can be purchased from an authorized distributor.

Use levelers NL410 / NL410G with care, protect from moisture. Never put a wet instrument to

the transport box (wait until dry).

CONTROL PANEL

4 8

3 7

2 6

1 5

Description of buttons and functions:

1) On / off power and switch to manual mode

- Turns on and off

- Longer press of a button - approx. 6 seconds. (when the equipment is turned on) enables /

disables the manual mode. The equipment in manual mode can be tilted (beyond self-levelling)

or work in difficult terrain, near the heavy construction equipment (does not react to the

vibrations of the land). When the equipment is switched to manual mode, the display shows the

"hand" icon.

2) Adjusting the rotation speed of the head

- available head spin speeds: 100-200-400-800 rpm. Each press will switch speed. When

working on smaller distances, classic measurements - choose 400 rpm. When working on large

distances and with the cooperation of machine control systems, select 800 rpm. Keep in mind

that the faster the head rotates, the energy consumption is greater

3) Select the inclination in axis (X, Y)

- Use the button to select the direction of the inclination (X, Y). Plane can be tilted up to ±8%

4) laser inclination mode switch (device automatically switches to manual mode)

5) movement alarm mode (TILT) / “WIND” function

- The laser is able to secure. While the device is moved, placed in another place (which can

cause incorrect measurements) –it turns off (system beeps). In such a situation, turn off and on

laser level again (or turn off the TILT by button 5). “WIND” function - after shock-moving the

laser re-levels.

6) directional scan button - narrowing of the laser line in the required range (where the work is

carried out)

- available display of beam angles: 0 -10° -45° -90° -180°. Each press will switch the display of

the beam angle.

7) MINUS / right rotation

- Use the key to: subtract the value of inclination (minus) / heads turn to the right (when the

head is not spinning or level is switched into scan mode)

8) PLUS / counter-clockwise rotation

- Use the key to: add the value of inclination (plus) / turn heads left

WORKING WITH LASER LEVEL

Turning on the power

On the front panel press button 1. The instrument will level by itself and the power LED lights

up. Press the button again to turn off the power.

Once leveled up, the laser LED stops blinking and the laser head rotates at a speed of 600 rpm.

If instrument will be is set inclined more than ± 5°, it won't level by itself.

Rotating laser head mode

button 2 allows you to adjust the speed of laser head rotation. Switching the speed is carried out

by pressing again this button

Scan mode

Adjust the rotating speed of the head. Press button 6 which will cause the device goes into scan

mode, the laser will begin to "draw" a line at set distatnce. Each time when you press this button

you will cause increase the range of "drawn" line. Depending on your needs, switch the direction

of rotation of the head (clockwise or counter-clockwise).

The inclination of laser plane

NL410/410G allows you to incline the laser plane in one or two directions

Press 4 button which will go into a mode of enter the inclinations

Press 3 to enable selection of the axis along which surface will be tilted (X or Y).

To set the inclination in the X-axis, press the buttons 7, respectively (positive values) or 8

(negative values) - every time pressing the laser beam will tilt to the surface - in the X or Y

plane, on the top cover of the laser are marked directions of inclinations. Positive values will

incline laser plane according to the arrow on the top cover, negative - in the opposite direction)

After entering the inclination value for the X-axis, Y-axis, press 3 again after approx. 3 seconds,

the plane begins to be tilted to entered values.

Press the 4 button to exit set inclination mode, the plane will be automatically levelled.

TILT function (function is active by pushing buttons 5).

Enable this system will cause the icon at LCD will present. After automatic levelling of the

instrument, after about 3 seconds, the TILT function is activated. Excessive inclination of the

instrument or unwanted movement / strike of the instrument will cause the TILT starts - warning

the user about disleveling of instrument (rotation is stopped) - it protects work with the wrong

referential plane. Function is working only with horizontal plane (without slopes).

WIND function (function is active by pushing buttons 5).

The equipment automatically adjusts the level of the displayed beam in real time to the field

conditions. When the position of the instrument changes during work, it will be subjected to

vibrations (machines work in the area / strong wind) - the compensator corrects the

inconvenience and leveling the beam display at all times (without switching off the equipment),

ensures continuity of work in extreme conditions on the construction site. Function is working

only with horizontal plane (without slopes).

PRINCIPLE OF OPERATION

Height Measurement

Turn the power on to Level the instrument itself. Once leveled, the laser head

starts to spin, setting the laser plane. Attach the laser sensor on the laser

staff. Place a laser staff with attached sensor on a benchmark (zero point)-

reset the position of sensor (adjust the height of the sensor to define a zero

level, the laser staff should also indicate zero). Move the laser staff with

sensor to another point which height you want to measure, adjust the height

of the sensor to place it in the field of the laser beam - move it up or down on

the laser staff. The difference of sensor positions on the staff will indicate the

height differences of the measured point compared to the benchmark.

Slope determination

Set the laser level on a tripod. Set the laser level in the axis you want to tilt

and turn on the laser level. The laser plummet (bottom) indicates the first

point of the axis, on the other end point set the laser staff with laser sensor -

reset position (sensor and staff). Depending on the desired value of inclination

slide the sensor on a staff and by remote control change the inclination of the

laser plane in order to fit in the position of the laser sensor (this shift of laser

sensor will specify the inclination, eg. If you want to get a inclination of 1%, at

a distance of 10 m (laser staff) the difference between the height of the zero

point on the staff should and designated inclination should be 10 cm).

Working with the vertical plane

NL410 / NL410G can set horizontal or vertical beam. If you work with a vertical laser beam

you must set the laser level as in the picture beside. After switching on the laser level the

device will level by itself –the head will start to rotate - setting a vertical plane.

The laser plummet (top) defines a line perpendicular to the plane of the laser level, which

is used in all perpendicular works (building partitions, setting 90°angle, etc.).

To set up vertical line of laser please use buttons + / - (no. 7, 8 –at control panel graphic).

Remote control

Features of NL410 / NL410G laser level can be controlled remotely using the remote control.

On the remote control panel there are buttons that correspond to those included on the front

panel of laser level. The operating range of remote control is approximately 20 meters (depends

on the conditions on the site)

Checking the laser level

You should regularly check the following parameters of the laser level

setting a horizontal plane

cone error

setting a vertical plane

Checking and calibration of the horizontal and vertical planes is simple and in most cases can

be done by the user. Checking the cone error can be also done by the user, but this error can

be only removed by an authorized service center.

Checking the horizontal plane

1. Set the instrument about 30m from the wall so that the X-axis is perpendicular to the

wall and X direction a pointed to a wall.

2. Turn on the instrument and wait until it level automatically.

3. Place a sheet of paper on the wall. Mark the position of the laser beam on the sheet.

Turn off the instrument.

4. Loosen the tripod fixing screw and rotate the instrument 180°.

WARNING! Be careful not to move the instrument while the head is spinning.

5. Turn on the instrument once again and wait until it level automatically.

6. Once again mark the position of the laser beam on the sheet.

7. Measure the distance between the marks, if the distance is less than 6 mm calibration

is not necessary, in other case please contact service center

8. Perform similar operations for the Y axis .

Checking the cone error

Please do this procedure after calibration of horizontal plane.

1. Set the laser centered between the walls distanced from each other of 30 m. Set the

instrument in the X or Y direction.

2. Mark the position of the laser beam on both walls.

3. Turn off the instrument and move it near to the of one of the walls (1 to 2 meters). Do not

change the orientation of the axes. Turn on the instrument.

4. Again, mark the position of the laser beam on the walls

5. Measure the distance between the marks on the walls.

6. If the difference in distance is less than 3 mm, it can be assumed that this error does not

occur.

Warning! If this error is more than 3m, you should contact the service center.

Checking the vertical plane

This procedure should be done after calibration of the horizontal plane.

1. Set the laser centered between the walls distanced from each other of 30 m

2. Turn on the laser level.

3. Place the paper sheets on the walls and mark the position of the laser beam.

4. Turn off the instrument. Set the instrument in vertical position near to one of the walls.

5. Turn on the instrument.

6. Mark the position of the laser beam on the paper sheet. Measure the distance

between the markers

7. Do not change the position of the laser and spin it 180°.

8. Mark the position of the laser beam on the paper sheet. Measure the distance

between the markers

9. If the distance between the markers is less than 3mm calibration is not necesery.

Laser sensor RD400

magnets

coarse mode (±2mm) precise mode (±1mm)

too high,

the laser signal is below laser signal receiver

(please Lower the sensor) Indicators

- you will hear a high frequency sound

you are in the right position Indicators

- you will hear a continuous sound

too low,

the laser signal is above

- you will hear a high frequency sound

discharged batteries

buzzer on / off

operating mode sound signal/buzzer

LCD backlight ON/OFF button

Laser sensor RD600 Digital

display laser detector area

level„zero”

LED grade indicator

lbubble

keypad

magnet

unit (mm, cm, cal)

On/Off / Beeper volume

deadband resolution / LED On/Off

Display

numeric / text display

grade indication arrows

on grade indicator

low battery grade indication arrows

accuracy (1 / 2 / 5 mm) beeper volume

Battery

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Nivel System Laser-Nivelliergerät Handbücher

Nivel System

Nivel System NL810 Bedienungsanleitung

Nivel System

Nivel System DT-2 Bedienungsanleitung

Nivel System

Nivel System NL510 Bedienungsanleitung

Nivel System

Nivel System NL311 Bedienungsanleitung

Nivel System

Nivel System CL1G Bedienungsanleitung

Nivel System

Nivel System CL8 Bedienungsanleitung

Nivel System

Nivel System NL540 Bedienungsanleitung

Nivel System

Nivel System NL200 Bedienungsanleitung

Nivel System

Nivel System CL4D-G Bedienungsanleitung

Nivel System

Nivel System NL740R Bedienungsanleitung

Nivel System

Nivel System NL301 Bedienungsanleitung

Nivel System

Nivel System CL2 Bedienungsanleitung

Nivel System

Nivel System CL4D-R Bedienungsanleitung

Nivel System

Nivel System NL610 Bedienungsanleitung

Nivel System

Nivel System CL2R Bedienungsanleitung

Nivel System

Nivel System N24x Bedienungsanleitung

Nivel System

Nivel System MC-1D Bedienungsanleitung

Nivel System

Nivel System CL4 Bedienungsanleitung

Nivel System

Nivel System NL540G Bedienungsanleitung

Nivel System

Nivel System DL60 Bedienungsanleitung

Nivel System

Nivel System NL Series Bedienungsanleitung

Nivel System

Nivel System EL-32 Bedienungsanleitung

Beliebte Laser-Nivelliergerät Handbücher anderer Marken

Nedo

Nedo ET-5 Bedienungsanleitung

geo-FENNEL

geo-FENNEL Maxi-Liner FL 65 HP Bedienungsanleitung

LaserLiner

LaserLiner X2-Laser Bedienungsanleitung

Spectra

Spectra LL300N Bedienungsanleitung

geo-FENNEL

geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Bedienungsanleitung

Nedo

Nedo Crossliner 4 Bedienungsanleitung

Lasertec

Lasertec FX360G Bedienungsanleitung

Flex

Flex ALC 8 Bedienungsanleitung

Black & Decker

Black & Decker LZR5 Bedienungsanleitung

Johnson

Johnson 40-6692 Bedienungsanleitung

Cocraft

Cocraft HL 20-SG Bedienungsanleitung

Zircon

Zircon iLine Bedienungsanleitung

HWH

HWH 310 SERIES Bedienungsanleitung

Leica

Leica iCON robot 60 Bedienungsanleitung

LaserLiner

LaserLiner SuperCross-Laser SCL 2 Bedienungsanleitung

LaserLiner

LaserLiner ActiveFinder XP Bedienungsanleitung

DeWalt

DeWalt DW082 Bedienungsanleitung

imex

imex EL20 Bedienungsanleitung