Nokeval 592D Bedienungsanleitung

No 090203 Nokeval

Manual

Model 592D

Nokeval oy

Yrittäjäkatu 12

37100 Nokia, Finland

Tel. 358-3-342 4800

Fax. 358-3-342 2066

Field dsplay 592D has 57 mm digit heigth. The large

display is designed for max. 20 meters distance. The field

display consist of two displays, 5 digits, max. 99999.

ModelhasredLEDdisplaywhichcanbeseenalsooutdoor

applications using a sun shade in the enclosure. The

• Dual 5 digits, 57 mm display

• Microprosessor based

• Pt100 sensor, thermocouples, 0/4..20

mA, 0/5..10V, potentiometers

Analog input:

Dual large field displays

Specification:

Voltage inputs:

Scaleable inputs: -9999..99999

0-1V, 0..5V, 1-5V, 0-10VDC

Input ranges : 20, 50, 500, 1000 mV

Input impedance: 1 Mohm, for 500 and 1000 mV, 10

kohm for 25 and 50 mV.

Decimal point selectable

Accuracy: 0.05 % of FS.

Current input 0/4..20 mA:

Display range: -9999....+99999

Offset: 0-99 %

Desimal point selectable

Input impedance: 50 ohm .

Accuracy: 0,05 % of FS.

Potentiometer input:

Input range 25....1000 ohm or

2...10 kohm

Scaleable display.

RTD sensors:

Pt100

2-, 3-, or 4 wire connection

Temperature rangee -200... +700 °C

Resolution 0.1 or 1 °C

Accuracy:

0,05% of FS + 0,1 °C (4-wire.)

0,05% of FS + 0.2 °C. (3-wire)

Error between channels, max. ± 0,1 °C.

Lead wire resistance effect:

(3-wire) 0.005%/ohm.

Other RTD-sensors available:

PT500, Pt1000, Ni100, Ni1000

Thermocouples:

K -100....+1250 °C

J,J/DIN -100..... +900 °C

T -50...... +350 °C

E -50....... +350 °C

R,S 0......+1700 °C

B 0... . +1800 °C

W3 0......+2300 °C

W5 0......+2490 °C

W 1000.. ..+2300 °C

N -200.....+1200 °C

Accuracy 1.5 °C ± 1 numero

S,R types 2.5 °C ± 1 numero

Lead wire < 1000 ohms, no effect

Cold junction effect: < 0.05 °C/°C.

General specification:

5 digits., red, LED, digit height 57 mm. Grey plastic

case.

Digit size 57 mm

Protection IP65

Power supply 230 VAC, 20 W

analog conversion is 15 bit and resolution 1/32000.

Continuosautocalibrationquaranteeslongtermaccuracy.

When you display big numbers the last digits on right may

be set to indicate zeros (null digits).

Connections for channel B

as channel A.

B+ - c + +

+ - c +

K1 K2

Pt100

2,3 4-

wire

Pt100

2,3 tai 4-

wire

+ -

Input: 0/1..5/10VDC:

Current 0/4..20 mA:

Potentiometer:

5/10 V

Output (V)

0/1...5/10 V

Thermocoupleand

mV-input:

Pt100 3-wire.

Pt100 4-wire.

Pt100 2-wire.

+Power supply

10 ja 12

Standard:

220 V AC

Channel A

Channel B

- +

Output (mA):

(0) 4..20 mA

Connections

N L

Note 1.

Output 0/1..5/10 : Connect jumper to

connectors 7 and 19.

Power supply:

Standard 220

Others 110, 24 V AC or

24 V D

24 VDC, connectors:

11(+) ja 10 (-).

Contacts:

selectable nc or no

Alarms

max. 240 V, 2 A

Protection: IP65

Black metal case

Wire connections: 2 x 13.5 mm

Dimensions: mm

Dimensions

670

625 120

646

210

250

d 7.0

Keyboard for configuration

Mother board

*-button

E T *

A B

Channel A Channel B

CONF

CONF END

END

*-button **

Channel AB

(optional) Common When display shows

symbol END you can

exit from programming

stage by pressing *-key.

Only when two

channels in use

(optional)

Indication lights

of alarm one and

two

Selection for upwards

(up button)

Selection for downwards

(down button)

Display

Indication lights

of channel 1 and 2

Youcan enterconfiguration stagethrough threebut-

tons on circuit board. Buttons E and T, on the left,

transfer indication lights in main menu and *-button

confirms selection. Alarms are available on request.

You can enter initial setting stage when all indication

lights are OFF. See chapter "initial settings" on next

page.

Indication lights (A and B)

AB AB off

(E,T)

confirms selection

Configuration

You can configurate the meter by three push buttons on circuit board. Display will show symbols,

which can be changed, or the settings may be controlled only. *-button will not change

settings but it transfers display and program to next stage.

Select config stage by pressing E , T and * -buttons at the same time.

CONF-text appears on the display. Now you are ready to start configuration.

Initial settings You can select the number of channels, output etc.

Display Push buttons

CONF Turn off lights A ja B by arrow keys and press *-button.

d i Select the number of digits (4 or 5 digits)

CH x Select one or two input channels. A=(CH1)1, B=(CH2) 2

SP 0 Extended channel AB. 0=OFF 1=ON

OU x Factory default, must be set to = 0

AL 0 Factory default, must be set to = 0

1 nc Factory default, do not change

F 50 Select line 50 or 60 Hz (default 50 Hz)

CCxx Special functions.

Setting of secret code

xx = 88, Secret code for configuration

xx = 89, Secret code for only alarms

Setting of secret code for configurations

CC 88 Choose number 88 by down-button. Display will show text CODE.

CODE Press *-button.

0000 Display will show number number 0000 and first 0 is blinking.

Choose any number between 0..9 and make following number to

blink by *-button. When 4 number code is set press *-button. Exit by

choosing CC90 and press *-button. Secret code is saved first when

you leave program stage (END). Code number 0000 is not in use.

You may select any number between 0001...9999.

Setting of secret code for only alarms

CC 89 Choose number 89 by down-button. Display will show text CODE.

CODE Press *-button.

0000 Display will show number number 0000 and first 0 is blinking.

Choose any number between 0..9 and make following number to

blink by *-button. When 4 number code is set press *-button. Exit by

choosing CC90 and press *-button. Secret code is saved first when

you leave program stage (END). Code number 0000 is not in use.

You may select any number between 0001...9999.

Channel A Channel B Channel AB

CONF Select channel A (CH1), B (CH) or AB (lights on front )

SExx Select measuring sensor, xx = 0 ... 74

1 0..20 mA Scaleabledisplay

2 4..20 mA Scaleabledisplay

11 Pt100 3-wire

12 Pt100 4-wire

13 Pt500 3-wire *

14 Pt500 4-wire *

15 Pt1000 3-wire *

16 Pt1000 4-wire *

17 Ni100 3-wire *

18 Ni100 4-wire *

19 Ni1000 3-wire *

20 Ni1000 4-wire *

21 1000 ohm Linear reistor 0..1000 ohm

22 500 ohm Linear resistor 0...500 ohm

31 TC B Thermocouple *

32 TC E Thermocouple

33 TC J Thermocouple ANSI FeCuNi

34 TC J DIN Thermocouple DIN FeCuNi

35 TC K Thermocouple

36 TC N Thermocouple

37 TC R Thermocouple

38 TC S Thermocouple

39 TC T Thermocouple

40 TC W Thermocouple *

41 TC W3 Thermocouple *

42 TC W5 Thermocouple *

51 0...10 VScaleabledisplay

52 0...5 V Scaleabledisplay

53 1...5 V Scaleabledisplay

54 0...1V Scaleabledisplay

61 Potentiometer max. 0-1000 ohm

62 Potentiometer max. 0-500 ohm

63 Potentiometer max. 0-50 ohm

64 Potentiometer max. 0-25 ohm

71 1000 mV

72 500 mV

73 50 mV

74 25 mV * = preliminary information

You can configurate both channel individually. Sensor types, alarms, display scaling and output

signals. Before channel configuration you shall decide in chapter "Initial Settings" whether

one or two channels, secret code etc. will be used. See chapter "Initial settings".

Channel settings

FU x Select function for channel A or B

0 Lineardisplay

3 log x

4 ln x

510

6xe

7 average (3 measuring values)

8 average (5 measuring values)

9 min. value Reset: press both arrows keys

simultaneusly 10 max. value Reset: press both arrows keys

simultaneusly

EN x Select whether the channel will be displayed by automa-

tic scanning =0 (not displayed), 1= (displayed)

ED x External display, 0=Off, 1=On (only for serial output)

DE x Decimals in display , x = 0 ... 3

LOFF Offset changing, f.ex. -1.0 degrees below measured

value xxxx Select offset value. You can change it any time

Scaleable inputs:

If sensor number is 1, 2, 12, 13, 14, 15, 16, 17, 18 or 19,

you have to select min/max display as follows:

LO Low-end of display (f.ex.. 4mA=0.0)

xxxx Select value

HI High-end of display (f.es. 20 mA=100.0)

xxxx Select value

OC x Factory default = 0, do not change

CONFCONF CONF

DONE

Press *-button

A B

Light A

END

Select END-text by arrow buttons and press *-button. When text [DONE] appears,

all parameter are saved to memory and indicator is ready to measure in a few seconds..

End of configuration

CONFCONF CONF END

A B Lights A....AB AB End of

configuration

You can select the number of channels, output etc.

Display Push buttons

CONF Turn off lights A ja B by arrow keys and press *-

button.

CH x Select one or two input channels, x, , 1=1 2=2

channels

SP 0 Exrtended channel AB. 1=OFF, 1=ON

OU x Output 0/4..20 mA or 0/1..5/10VDC On=1, Not

used=0 CCxx Customized calibration of potentiometers and current

output xx = 11, Potentiometer, channel A

xx = 12, Potentiometer, channel B

xx = 21, Current output 0/4..20 mA

xx = 22, Voltage output, 0/1..5/10 V

CC 11 (A) or CC 12 (B) (Select number by arrow-keys).

1. Run potentiometer to min. position (or max. position in of reverse function) when display shows

symbol P_lo and press then *-button. Resp. when display shows P_Hi

2. Return by arrow buttons symbol 0 and press *-button so many times until display shows

configuration start symbol CONF. You can now get symbol END by arrow buttons. Confirm exit

by *-button. The display now shows symbol DONE and the meter is calibrated fror the real path

angle.

adding output card.

Teaching potentiometer position

If the path of the actuator is not from zero to max.

value but, only a apart of it, you may calibrate meter

to correspond the real-path. Indicator saves to its

memory min./max. positions and this does not chan-

ge the scaling of the display. F.ex. display is scaled

0..100% corresponding 0-1000 ohm. In the field,

however,whenthevalveisclosedtherealvalueis70

ohmandwhenclosedtherealvalueis872ohm.This

means that display do not show 0-100% as desired.

This drawback can be easily corrected as follows:

Potentiometer input

Meter accepts pot. input in both channels, each

having its own scaling. Standard ranges are

0..25...1000 ohm. Inside the meter you can change

two resistor for range 10 times, ie. 0..250...10000

ohm.Ifyou usethe expanded rangeyou cannotuse

RTD´s. Standard range allows RTD, or some other

sensor on the other channel. You can set all mathe-

maticalfunctionsalso topot.input asf.ex.logaritmic

scaling display. You can also have output signal by

CONFCONF

CONF END

FU Choosing the function. see table 2

EN x You can pass a channel in automatic scanning,

0=pass, 1=shows

ED x External display 0=OFF, 1=ON

DE x Number of decimals, x = 0 ... 3

AC x Alarms and output can be chosen for channel A

and B. Set output and alarms to channel A and B.

Go to page "programming" and continue from point A

Cxx or press *-button, without doing any settings,

see point "exit".

Press *-button

Third channel AB

The lights A and B (AB) indicate that display

shows the result of calcutation, which can be

used as a separate channel. You can select

the functions like sum, subtraction, square root

etc. in a separate table.

A B Lights A....AB AB

Channel A or B

Definition of mathematical functions for third channel

(optional)

The display may show the third (extended channel)

i.e. the result of the calculations between the two

channels.ThebothsignallightsAandBlitatthesame

time. The third channel operates excatly like the

physical channels and may have alarms or output

signal.

Definition of functions to channel AB

Choose channel AB to display by arrow buttons and

press *-button

Inhaltsverzeichnis

Andere Nokeval Messgerät Handbücher

Nokeval

Nokeval 2026 Bedienungsanleitung

Nokeval

Nokeval eGate-Kombi-LWUS-RHT-CO2-TVOC-Dust40-DP Bedienungsanleitung

Nokeval

Nokeval 575F-2071 Bedienungsanleitung

Nokeval

Nokeval FT10 Series Bedienungsanleitung

Nokeval

Nokeval Stable-LWEU-T-DI Bedienungsanleitung

Nokeval

Nokeval Solid-Sky-2Pro-24VDC Bedienungsanleitung

Nokeval

Nokeval 2012 Bedienungsanleitung

Nokeval

Nokeval 575F Bedienungsanleitung

Nokeval

Nokeval Kombi-LoRaWAN Bedienungsanleitung

Nokeval

Nokeval PME600 Bedienungsanleitung

Nokeval

Nokeval BEAT10-T Bedienungsanleitung

Nokeval

Nokeval 2800-2071 Bedienungsanleitung

Nokeval

Nokeval 575F Bedienungsanleitung

Nokeval

Nokeval KMR260 Bedienungsanleitung

Nokeval

Nokeval 2061 Bedienungsanleitung

Nokeval

Nokeval 201 Bedienungsanleitung

Nokeval

Nokeval 2022Setp Bedienungsanleitung

Nokeval

Nokeval Ovasense Neo Series Bedienungsanleitung

Nokeval

Nokeval Solid-Sky-2Pro-DIO-RS485 Bedienungsanleitung

Nokeval

Nokeval PM10A Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung