nologo ADR3000 Bedienungsanleitung
User Manual
Teye ADR3000
Automated Drive Recorder
Unlike other in-car recording systems, the Drive Recorder is used to record
both video and audio data in a continuous loop fashion. If the vehicle is
involved in an accident such as a collision, impact, and sudden acceleraon-
related incident, this data is marked and stored. One may thereaer analyze
the data to find its root cause by playing back the scenes of interest and
where acceleraon, vehicle speed, direcon, and locaon are available for
review. Added to the recording are vehicle speed and direction and GPS
locaon.
Main Features
Connuous recording
The video and audio data from the front and interior views is connuously recorded while power
on. When the capacity of the SD card has been reached, the oldest files are overwrien by the
latest ones in a “round-robin”, first in, first out fashion.
Pre and post event recording
When impact or unusual acceleraon or deceleraon is detected by the built-in G-Sensor and has
exceeded the preset limit or one acvates the manual emergency record buon, the recorded
video data is locked-in and is erased only by an authorized party and by using a PC or laptop,
accessing the SD card. Event data records 1 minute before and 1 minute aer(Note: The User may
set the pre-event me to either 1 minute, 2 minutes or 3 minutes of pre-event recording). The
next me the SD card is read by the unit, the unit’s set up parameters will be uploaded into the
recorder. As previously menoned, stored event recording data in the SD card will not be erased
by the unit, and where this must be done manually by the user.
Night view recording with Infra-Red Light
The included IR (Infra-Red) Light module with adjustment used this invisible light source to assist
in recording nighme views from the interior facing camera.
Playback of video/audio data
The recorded data can be played back using the provided playback soware which resides on the
SD card. By removing the SD card and accessing the Player folder and double clicking on the “Player.
exe” line starts the playback soware.
Data analysis
The recorded data can be easily analyzed for speed, vehicle location and direction of travel
including impact by using the Player that is found on conveniently on the supplied SD card.
0202
03
Safety Instrucons 4
Components 5
Part Numbers 6
IR (Infra-red) light module 7
Technical Specificaons 8
SD Memory Card specificaons 8
Installaon 9
Installing the Unit 9
Installaon of the IR (Infra Red) light 9
Installing the Remote Manual Alarm Event Buon 10
Connecng the power cord 10
Tips before Using the Product 11
Unit Preparaon for video recording 11
Connous recording while driving 11
SD card related informaon 12
Funcons of each part 13
Using the Player: Playback, SD card and Inial System Set-Up 14
PC Minimum Systems Requirements 14
To Review Video 14
Playback Interface Controls 15
Volume and Playback Speed Control 15
System configuraon 16
Playback 17
Converng the Authencated files into AVI file format 18
Interfacing with a GIS/City map 19
Addional Funcons of Player: Pop-up Display window 20
Analyzing G-SENSOR data 21
System Diagnoscs via the LED Display 22
Firmware and Playback S/W Update 23
Firmware Update 23
Soware Update 23
Contents
04
Before using the product
◆ Damage due to producon malfuncon, loss of data, or other damages occurring while
using this product shall not be the responsibility of the manufacturer.
◆Although the Drive Recorder is a device used for recording/storing videos, the device is
not guaranteed to record informaon on every accident in the case of a malfuncon.
◆ In the case of an accident, a minor force will not trigger the G-Force sensor to acvate
Event Recording. Therefore the user must use the Manual Record Buon located on the
device itself.
◆For stable use of the product, check the product and SD card regularly to ensure its
proper operaon.
User Manual
úTo ensure proper operaon please read the manual before installaon and use.
Failure to follow this safety noce may cause a malfuncon and may void the warranty.
Power
úUse only the provided cables and specified power input.
A cable not supplied by the manufacturer may cause product damage,
a fire or a short circuit.
úPlease use rated capacity for the fuse and confirm the message if the product correctly
connected aer the installaon.
SD memory card
úInsert the SD card to the product.
úEnsure that the capacity of the SD card is not exceeded.
öA full SD card will not allow one to record manual alarms or G-sensor based triggers.
ú1MFBTFNBLFTVSFUPUVSOPGGUIFEFWJDFQPXFSXIFOJOTFSUJOHPS
FKFDUJOHUIF4%DBSE
öInside SD memory data loss may occur due to SD error.
Warranty and responsibilies
Safety Instrucons
To ensure proper operaon please read the manual before installaon and use. Failure to
follow this safety noce may cause a malfuncon and may void the warranty.
Safety Instrucons
04
Do not clean the product with
water or volale solvents.
This may damage the product,
cause a fire or electric shock.
Do not apply excessive shock or
never insert foreign materials into
the product.
This may cause product damage, a
fire or a short circuit.
Video quality is affected by
lighng condions. GPS is affected
by signal receipt.
Nighme or use in tunnels affects
system operaon.
Do not arbitrarily change the
product locaon.
This may cause a GPS
communicaon error.
Do not disassemble, repair or
modify the product.
This voids the warranty and
where we take no responsibility
for product damage or problems
caused by the user.
Any excessive window nng may
cause an unclear or distorted image
on playback.
First record and then play back the
video to see if the recorded video is
acceptable.
Do not cover the camera lens
with any materials or objects.
This may affect recording quality.
Once installed, do not manipulate
the product while you’re driving a
car.
This may cause a traffic accident.
Ensure that the capacity of the SD
card is not exceeded.
A full SD card will not allow one to
record manual alarms or G-sensor
based triggers.
Use only the provided cables and
specified power input.
A cable not supplied by the
manufacturer may cause product
damage, a fire or a short circuit.
Do not obstruct the view of
the product through the front
windshield.
The GPS receiver may not work
properly.
Only use factory approved parts.
Use the approved power cable.
Contact your authorized Reseller
for assistance.
Components
05
ö
Depends on the model ordered, SD card cannot provide.
Components
Manual Fuse
IR Light Module External Alarm Button
Body Holder
Cigarette Lighter Plug for
Power Supply
SD Card
06
Part Numbers
3
4
12
5
68
910 11
7
No. Name Descripon
1Power Connecon Port Used to connect the power cord with the unit.
2Power Connecon Port Used to adjust the audio volume for informaon.
3Forward Facing Camera Used to record scenes through the windshield.
4Mounng Connecon Used to mate with the mount.
5Built-in Speaker Provides audio output for chime and any informaon.
6Status Display Used to display the status of Drive Recorder or traffic
informaon by using English text or symbols.
7IR Light Connecon Used to mate with IR Light module.
8Interior Facing Camera Records video from inside your vehicle.
9Emergency Record Buon Used to perform an emergency recording.
10 Emergency Record
Protecon Cancel Buon
Used to cancel protecon of all the emergency recording
data.
11 SD card Slot Used to insert the SD card into unit.
07
IR(Infra-red) light module
No. Name Descripon
1CDS Used to sense the brightness while nighme recording.
2reverse side Connecon port to main body
3Power Connecon Used to connect the power cord to the IR light module.
1
2
3
ö
The effecve range of the IR light module covers the first row of back seats.
08
SD Memory Card specificaons
Size of SD
Memory
Maximum
Storage
Time
Event Recording
Time
Number of Event Generated
Recordings according to the
Preset Recording Time
1mins 2mins 3mins
2GB 90 minutes 64 minutes 25 20 15
4GB 180 minutes 80 minutes 50 40 30
8GB 370 minutes 160 minutes 90 80 70
16GB 750 minutes 320 minutes 120 100 80
Technical Specificaons
Item Specificaon
Camera Type 1.3 Mega Pixel CMOS sensor
Video Resoluon VGA (640 x 480) up to 15 frames per second
Audio Built-in microphone
GPS Built-in GPS module
Automac Event Sensor,
Alarm input
G-sensor (3-axis),
Manual / external alarm trigger
Memory SD Card (512M ~ 16GB)
Power Input Body DC 5V to recording unit
Cigaree Lighter Plug DC 12V ~ 24V
ö
4GB SD memory card included with install package.
ö
Time varies depending on the amount of moon seen by the camera & lighng condions.
ö
Denotes an average me. (Moon affects recording duraon. Times reflected see recordings made
during the dayme in typical city downtown areas.)
09
Be sure to stop the engine before installing the product.
Remove all power to any areas where wires will be connected.
Install the product in a locaon where the satellite signals are received.
Before permanently mounting the unit, ensure that the camera views meet your
requirements. (ex: where the interior view is not hidden by the mirror inside your car)
The Unit must be installed on the mounted straight both horizontally and vercally
Installaon
Cauon
Connect power to the unit once the IR light module has been connected.
Aim the IR light module towards the driver and passenger area.
Cauon
Installaon of the IR (Infra Red) light
Insert the IR light module’s
knob, on the rare face of
the body.
1Connect the other side
of “Y” power cable to the
power connection port
of the attached IR light
module of the unit.
2
Installing the Unit
Insert the holder into the
mounng connecon.
1Clean the mounting
surface and remove
the red film from tape
the mount, and press in
place the mount to the
windshield ghtly.
2
Clean the mounting
surface and remove
the red film from tape
the mount, and press in
place the mount to the
windshield ghtly.
3
Inhaltsverzeichnis
