Norac Case AFS Pro 300 Bedienungsanleitung
Case AFS Pro 300, 600, 700 Display Kit
(20 & 30 Series - Self-Propelled)
Installation Manual
54VT-PRO-SP01
Copyright 2017 by NORAC Systems International Inc.
Reorder P/N: 54VT-PRO-SP01-INST Rev G (Case AFS PRO 300, 600, 700 (20 & 30 Series -
Self-Propelled Display Kit)
NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and
without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information
contained in this manual. The technical information in this manual was reviewed at the time of approval for publication.
1
Contents
1INTRODUCTION ...................................................................................................... 2
1.1VT Software Version..........................................................................................................................................................2
1.2List of Parts..........................................................................................................................................................................2
2INSTALLATION ........................................................................................................ 3
2.1CANbus Interface Installation..........................................................................................................................................3
2.2Switch Box Installation ......................................................................................................................................................5
3CABLE DRAWINGS.................................................................................................. 6
3.1ITEM C25: 50250 - Switchbox........................................................................................................................................6
3.2ITEM C26: 43240-47 – Cable UC5 Interface Switch Box - 50250 .........................................................................7
3.3ITEM C30: 43250-14 – Cable UC5 Battery 2 Pin DT Tee Fused (ECU & SIG) .................................................8
3.4ITEM C40: 43260-07 – Cable CANbus 3 Pin DT J1939...........................................................................................9
3.5ITEM C41: 43220-01 - Cable Network 14 AWG - 1M .......................................................................................... 10
3.6ITEM C42: 43260-29 – Cable Interface DT 4 Pin 12 IN Stub .............................................................................. 11
APPENDIX A: ALTERNATE CONFIGURATION..................................................... 12
2
1Introduction
The Case AFS Pro 300, 600, 700 Display Kit Manual is intended to be used in conjunction with
the UC5 Spray Height Control Installation Manual. This manual provides instructions to
interface the UC5 Control Module to the Case AFS Pro 300, 600 or 700 Display. For
installation of the rest of the UC5 Spray Height Control System please refer to the sprayer
specific manual provided with the kit.
1.1 VT Software Version
Before you connect the UC5 to the Case AFS Pro 300, 600 or 700, you must ensure that you
have the latest VT software installed. The VT software must be Version 25 or newer.
1.2 List of Parts
Item Part Number Name Quantity
C25 50250 SWITCHBOX 1
C26 43240-47 CABLE UC5 INTERFACE SWITCH BOX - 50250 1
C30 43250-14 CABLE UC5 BATTERY 2 PIN DT TEE FUSED (ECU & SIG) 1
C40 43260-07 CABLE INTERFACE CAN BUS 3 PIN DT J1939 1
C41 43220-01 CABLE NETWORK 14 AWG 1M 1
C42 43260-29 CABLE INTERFACE DT 4 PIN 12 IN STUB 1
M01
UC5-BC-MANUAL-OPERATOR
MANUAL UC5 OPERATORS 1
M04 54VT-PRO-SP01-INST MANUAL UC5 DISPLAY KIT CASE AFS PRO 300, 600, 700 (SELF-PROPELLED) 1
M05 UC5-USER-REF-GUIDE MANUAL UC5 USER REFERENCE GUIDE 1
P01 106034 NETWORK 2 PIN PLUG 1
P04 106027 NETWORK 2 PIN RECEPTACLE (PLUGGED) 1
3
2Installation
2.1 CANbus Interface Installation
1. Securely mount the control module (E01) on the center boom at the rear of the sprayer.
2. Tee the CANbus interface cable (C40) in to the Case “Application” CANbus. The
“Application” CANbus is either a 3-pin Deutsch connector or a 4-pin Deutsch connector.
It is located on the center section of the boom at the rear of the sprayer.
3. If the “Application” CANbus is a 3-pin Deutsch connector use cable C40 (43260-07). If the
“Application” CANbus is a 4-pin Deutsch connector use cable C42 (43260-29).
4. Connect the Deutsch plug on cable C40 or C42 to the end of the control module with only
one Deutsch connector.
5. Connect the power cable (C30) to one of the two CANbus connectors on the control
module.
6. There will be either a 2-pin DT plug or a 2-pin DT receptacle for power. Connect the
appropriate connector and plug the other with either P01 or P04. If there are no free
power connectors, tee the power cable (C30) into an existing power connection.
7. Connect cable C41 to the other CANbus connector and route the cable to the Valve
Module.
Figure 1: CANbus Interface Installation with Cable C40
4
Figure 2: CANbus Interface Installation with Cable C42
5
2.2 Switch Box Installation
1. Disconnect cable C20 (Thru 2 connector) from the input module (E03). Remove the wedge
from the face of the 12-pin Deutsch plug.
2. Insert the Roll CW pin from C26 into position 3 of the 12-pin plug on C20. Insert the Roll
CCW pin from C26 into position 4 of the 12-pin plug on C20. Insert the wedge back into
the plug. Connect C20 to the Thru 2 connector on the input module.
3. Connect the 12-pin Deutsch plug on C26 to the OEM 3 connector on the input module.
Route the other end of the cable to the cab.
4. Attach the switch box (C25) inside the cab and connect it to cable C26.
* Some sprayer types may not use all the switch functions.
* Refer to “Appendix A” for sprayers with European style slant control.
Figure 3: Switch Box Installation
6
3Cable Drawings
3.1 ITEM C25: 50250 - Switchbox
7
3.2 ITEM C26: 43240-47 – Cable UC5 Interface Switch Box - 50250
8
3.3 ITEM C30: 43250-14 – Cable UC5 Battery 2 Pin DT Tee Fused
(ECU & SIG)
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Norac Steuerungssystem Handbücher
Norac
Norac UC5 Topcon X30 Bedienungsanleitung
Norac
Norac UC7 Bedienungsanleitung
Norac
Norac UC4.5 Bedienungsanleitung
Norac
Norac UC4.5 Bedienungsanleitung
Norac
Norac UC4 Total Control Bedienungsanleitung
Norac
Norac UC5 Topcon X30 Bedienungsanleitung
Norac
Norac UC4.5 Bedienungsanleitung
Norac
Norac UC4.5 Bedienungsanleitung
Norac
Norac UC5 Can Bus Bedienungsanleitung
Norac
Norac UC4 Plus Rogator 64 Series Bedienungsanleitung
Norac
Norac UC5 Topcon X30 Bedienungsanleitung
Norac
Norac UC4.5 Bedienungsanleitung
Norac
Norac UC4+ Bedienungsanleitung
Norac
Norac UC4+ Bedienungsanleitung
Norac
Norac UC5 Topcon X30 Bedienungsanleitung
Norac
Norac UC4+ Bedienungsanleitung
Norac
Norac UC5 Active Roll Control Bedienungsanleitung
Norac
Norac UC5 Topcon X30 Bedienungsanleitung
Norac
Norac UC4.5 Bedienungsanleitung
Norac
Norac UC4.5 Bedienungsanleitung
