Norac UC4.5 Bedienungsanleitung
J
ohn Deere
(30 Series Main Lift Option)
Installation Manual
J
D9
Printed in Canada
Copyright 2012 by NORAC Systems International Inc.
Reorder P/N: UC4.5-JD9-INST Rev A (John Deere 30 Series Main Lift Option)
NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and
without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information
contained in this manual. The technical information in this manual was reviewed at the time of approval for publication.
Contents
1Introduction................................................................................................................ 1
2Kit Parts ...................................................................................................................... 2
3Ultrasonic Sensor Installation .................................................................................. 5
4Hydraulic Installation ................................................................................................ 8
5Electrical Installation ............................................................................................... 10
6Software Setup......................................................................................................... 11
7Cable Drawings ........................................................................................................ 12
1
1Introduction
Congratulations on your purchase of the NORAC UC4.5 Spray Height Control System. This
system is manufactured with top quality components and is engineered using the latest
technology to provide operating reliability unmatched for years to come.
When properly used the system can provide protection from sprayer boom damage, improve
sprayer efficiency, and ensure chemicals are applied correctly.
Please take the time to read this manual completely before attempting to install the system. A
thorough understanding of this manual will ensure that you receive the maximum benefit from
the system.
Your input can help make us better! If you find issues or have suggestions regarding the parts
list or the installation procedure, please don’t hesitate to contact us.
Every effort has been made to ensure the accuracy of the information contained in
this manual. All parts supplied are selected to specially fit the sprayer to facilitate
a complete installation. However, NORAC cannot guarantee all parts fit as
intended due to the variations of the sprayer by the manufacturer.
Please read this manual in its entirety before attempting installation.
2
2Kit Parts
2.1 Hydraulic Plumbing
Figure 1: JD9 Hydraulic Plumbing
3
2.2 List of Parts
The following tables list the John Deere 30 Series main lift kit (JD9) specific parts of the
NORAC UC4.5 system. This kit is to be used when installing the proportional main lift option
with existing John Deere installations.
Item Part Number Name Quantity
B21 44973 SENSOR MOUNTING BRACKET LOW PROFILE 16 GA LARGE FLANGE 1
C07 43220-01 CABLE UC5 NETWORK 14 AWG 1M 1
C17 44658-45D CABLE UC4 VALVE MAIN DT 1
E05 43750 UC5 ULTRASONIC SENSOR 1
E12 43764 UC5 NETWORK COUPLER 2-WAY 1
H03 44863-23 HOSE ASSEMBLY 122R2-06 32IN L 6FORX 6FORX 1
H10 44865-37 HYDRAULICS FITTING KIT - JD9 1
M01 UC4.5-JD9-INST MANUAL INSTALLATION UC4.5 JOHN DEERE 30 SERIES PROP MAIN LIFT OPTION 1
V01 44962D VALVE ASSEMBLY EXPANSION DPOC PROP DT 4 BOLT 1
4
2.3 Hydraulic Fitting Kit Details (P/N: 44865-37)
Item Part Number Name Quantity Picture
F03 104586 TEE ADAPTER - 6FORXR 6MORT 1
F05 44917 MALE ADAPTER - 6MB 6MOR 1
*F08 44926 ORIFICE INSERT 3/64" 1
F09 104369 PLUG - 6MBP 1
6 M B - 6 M OR X 90
SIZE IN
1/16TH'S
GENDER: MALE
OR FEMALE
90° ANGLE
SWIVEL
TYPE
GENDER
SIZE
TYPE:
B - ORB
J - JIC
OR - FLAT
FACE
P - PIPE
Fitting Name
Example:
* Orifice F08 is not required when installing on a John Deere 4930.
The use of dielectric grease is not recommended on any NORAC electrical
connections.
To ensure all stainless steel hardware does not gall or seize apply a light coating of
the supplied Permatex Anti-seize grease to all threaded parts upon installation.
Permatex Anti-seize lubricant is preferred, but other similar anti-seize products
may be used.
5
3Ultrasonic Sensor Installation
3.1 Ultrasonic Sensor Mounting Guidelines
The following guidelines will ensure optimal sensor performance and prevent
sensor measurement error. These rules should be followed for both the wing
sensors and the main lift (middle) sensor.
1. In its lowest position, the sensor must be 9 inches (23 cm) or more from the ground.
2. Ensure that there are no obstructions within a 12-inch diameter circle projected directly
below the center of the sensor.
3. The sensor should be approximately vertical at normal operating heights.
Figure 2: Sensor Mounting Guidelines
6
3.2 Low Profile Bracket Mounting Guidelines
1. Minimize the distance between the bolts to prevent bending the bracket and prevent the
bracket from loosening over time.
2. Ensure the bracket is mounted tight against the bottom of the boom, minimizing the
distance between the boom structure and the angled flange.
Figure 3: Bracket Mounting Guidelines
A problem can arise if a sensor is not mounted correctly. It is possible for the
sensor to read off of the boom instead of the ground. This may only become
apparent once the control system is switched from soil to crop mode.
Also be careful that the sensor bracket does not collide with any other part of the
boom when the boom is folded to transport position. If possible, mount the sensor
brackets while the booms are folded to ensure they will not cause interference.
7
3.3 Main Lift Sensor Installation
1. The main lift mounting bracket (B21) is the bracket with the longer mounting flange.
2. There are a variety of ways to mount the main lift bracket on most sprayers. The bracket
should position the sensor approximately in the center of the sprayer, forward of the
boom. An example of this mounting is illustrated in Figure 5.
Figure 4: Bracket Mounting Example
3. Mount the ultrasonic sensor to the main lift bracket. Run the sensor cable through hole
and behind the bracket.
Figure 5: Example Mounting of the Main Lift Bracket
Avoid mounting the main lift sensor over or near a wheel-track. Measurements
from the wheel-track do not provide an accurate crop height and will cause
measurement and control error.
Ensure the bracket does not collide with any other part of the sprayer throughout
the full range of main lift motion.
Front
Andere Handbücher für UC4.5
31
Inhaltsverzeichnis
Andere Norac Steuerungssystem Handbücher
Norac
Norac UC5 Topcon X30 Bedienungsanleitung
Norac
Norac John Deere 4720 Bedienungsanleitung
Norac
Norac SPRA-COUPE 7000 Series Bedienungsanleitung
Norac
Norac Rogator 700 Series Bedienungsanleitung
Norac
Norac UC7 Bedienungsanleitung
Norac
Norac UC4 Total Control Bedienungsanleitung
Norac
Norac UC7 Bedienungsanleitung
Norac
Norac PULSE UC5 Gebrauchs- und Pflegehandbuch
Norac
Norac UC4 Total Control Bedienungsanleitung
Norac
Norac UC4+ Apache 1010 2005+ Bedienungsanleitung
Norac
Norac UC4 Total Control Bedienungsanleitung
Norac
Norac UC4+ Bedienungsanleitung
Norac
Norac UC4 Total Control Bedienungsanleitung
Norac
Norac UC4+ Bedienungsanleitung
Norac
Norac UC4+ Bedienungsanleitung
Norac
Norac UC5 CANbus Bedienungsanleitung
Norac
Norac UC4.5 Bedienungsanleitung
Norac
Norac UC5 Topcon X30 Bedienungsanleitung
Norac
Norac Case AFS Pro 300 Bedienungsanleitung
Norac
Norac U5 Bedienungsanleitung
