Noritz VCK-NRCP-1 Kurzanleitung

Outdoor Vent Kit Installation and Instruction Manual

Do not connect electrical power to the unit until all electrical

wiring has been completed.

1. National Electrical Code

2. National Fuel Gas Code

3. In Canada, CSA C22.1 Canadian Electrical Code

Part 1, and CGA No. B149 (latest version)

4. Local, state, provincial, and national codes, laws,

regulations, and ordinances.

5. In the State of California: The water heater must

be braced, anchored, or strapped to avoid moving

during an earthquake. Contact local utilities for

code requirements in your area or call 866-766-7489

and request instructions.

6. In the Commonwealth of Massachusetts:

a. Outdoor units may be used for summer use only.

b. The water heater may be used for hot

water heating only and may not be used in a

combination of domestic and space heating.

Installation Must Comply With

This water heater must be installed by a qualied and licensed personnel. The installer should be guided by

the instructions furnished with the water heater, and by local codes and utility company requirements.

CAUTION

This manual is intended to be used in conjunction with

other literature provided with the water heater.

This manual includes all related control information.

It is important that this manual, all other documents

included in this system be reviewed in their entirety

before beginning any work.

Installation should be made in accordance with the

regulations of the Authority Having Jurisdiction, local

code authorities, and utility companies which pertain to

this type of water heating equipment.

Important

This installation manual includes information specic to outdoor water

heater installations. This information is meant to replace the venting

section included in the tankless water heater installation manual.

The tankless water heater installation manual includes instructions

that will be necessary for the proper installation of all other functions,

such as water and gas piping, wall mounting, control programming, etc.

Failure to follow these instructions could result in substantial property

damage, severe personal injury, or death. This installation shall be done

by a qualied service agency in accordance with these instructions, all

applicable codes, and requirements of the authority having jurisdiction.

Failure to follow these instructions could result in substantial property

damage, severe personal injury, or death.

WARNING

Note:

The manufacturer reserves the right to make changes or updates without notice and will not be held liable for errors in

literature.

PLEASE KEEP ALL INSTRUCTIONS FOR FUTURE REFERENCE.

Applicable for NRCP111/98 series only.

Kit# VCK-NRCP-1

Rev.02/19

Part Shape Qty

1 Outdoor Vent Cap

(w/ Plate and Packing) 1

2Exhaust Pipe 1

3 Exhaust Pipe Stopper 1

VCK Exhaust Adapter

(w/ P75 O-ring and

Packing)

Part Shape Qty

5 Vent Screen 1

Hexagon Head with Flange

Tapping Screw (M4 x12)

(Outdoor Vent Cap)

Truss Head Tapping Screw

(M4 x16)

(Vent Screen)

Instruction Manual

Included Outdoor Kit

Outdoor Kit Components Outdoor Kit Dimension

5.2" [133mm]

17.3" [440mm]

28.6" [728mm] 16.1" [410mm]

16.1" [410mm]

32.7" [832mm]

Outdoor Installation Location

1. Outdoor Installation Area Operating Conditions.

• Ensure ambient temperatures are higher than 5

°F

/-15

°C

• Prevent the air from becoming contaminated by the products, places, and conditions listed in the

water heater installation manual.

WARNING

Carefully consider installation when determining water heater location. Please read the entire installation

manual and these instructions before attempting installation. Failure to properly take factors such as piping,

condensate removal, venting, and wiring into account before installation could result in wasted time, money,

and possible property damage, personal injury, or death.

The outdoor kit is meant for use in outdoor installations ONLY. DO NOT install the water heater with

outdoor kit indoors. Installing the water heater with outdoor kit indoors will result in improper water heater

operation and property damage, and could result in serious personal injury or death.

WARNING

Incorrect ambient conditions can lead to damage to the heating system and put safe operation at risk.

Ensure that the installation location adheres to the information included in this manual. Failure to do so

could result in property damage, serious personal injury, or death. Failure of heater or components due to

incorrect operating conditions IS NOT covered by product warranty.

The water heater must be installed as described in these instructions: Upright, with the suppled outdoor

enclosure in the vertical position. DO NOT attempt to install the water heater in any other orientation. Failure

to follow these instructions will result in improper water heater operation and property damage, and could

result in serious personal injury or death.

2. Check for nearby connections to:

• System water piping

• Venting connections

• Gas supply piping

• Electrical power

• Condensate drain

Note:

The manufacturer reserves the right to make changes or updates

without notice and will not be held liable for errors in literature.

Install the water heater where any leakage from the relief valve, related piping, tank, or connections will not

result in damage to surrounding areas, lower oors of the building, or pool on the ground and freeze.

The water heater should be located near a drain or piped to a drain. Leakage damages ARE NOT covered

by warranty.

CAUTION

3. Check surroundings of water heater.

Remove any combustible materials, gasoline, and other ammable liquids.

WARNING

Failure to keep the water heater area clear and free of combustible materials, liquids, and vapors can result in

substantial property damage, severe personal injury, or death.

4. If the water heater is to replace an existing heater, check for and correct any existing system problems, such

as:

• System leaks

• Location that could cause the system and heater to freeze and leak

• Incorrectly sized expansion tank

5. Clean and ush system when reinstalling a heater.

Do not connect the water heater to any heating systems or components that have been previously used for

nonpotable applications. Do not introduce toxic chemicals, such as antifreeze or water heater treatments,

into the water heater or any piping meant for potable purposes. Ensure that all piping and components

connected to the water heater are suitable for potable water applications. Do not use this water heater for

space heating applications.

CAUTION

The

water heater must be installed level in order for the condensate to properly ow out the collection system.

CAUTION

Installation Clearances

Outdoor Installation Clearances

[ Table 1 ]

Minimum

Clearances

Installation Clearances

from Non-Combustibles

Recommended Service

and Proper Operation

Clearances

Top of appliance 36 in (900mm)

Back of appliance 5/8 in (15.9mm)

Front of appliance 24 in (600mm) 24 in (600mm) or more

Side of appliance 3 in (75mm)

Bottom of appliance 12 in (304.8mm)

Note:

The outdoor enclosure for this appliance

is approved for zero clearance to

combustible construction.

If the water heater is installed in a

narrow space or corner ensure that there

is sufcient space for service.

In multiple water heater installations,

ensure a minimum clearance of 36" from

the top of one water heater to the bottom

of the next water heater, and a minimum

clearance of 3" from the side of water

heater to the next water heater.

WARNING

Do not locate the water heater where exposed to prevailing winds.

Moisture will be produced by the exhaust vent. Take precautions when determining water heater location.

Moisture may fall from the vent termination to the ground and turn to ice in freezing conditions. Moisture or

ice can produce a hazardous condition.

Exhaust condensate is acidic and could deteriorate the surface below the exhaust vent termination.

Ensure this surface is in good repair (sealed, painted, etc.) to prevent deterioration. Failure to follow these

instructions could result in substantial property damage, serious personal injury, or death.

Prevent Combustion Air Contamination

Do not install the outdoor water heater in locations that

can allow contamination of fresh intake air.

Note:

See Table 2 to prevent combustion air

contamination.

• Front Clearance from Wall

• Clearance from Handrail with Common Side Corridor

36"[900mm]

or more

3"[75mm]

or more

24"[600mm]

or more

47"[1,190mm]

or more

84"[2,130mm]

Common side Corridor Handrail

• Clearance from Handrail on Balcony

Handrail

Balcony

24"[600mm]

or more

• Clearance from Wall and Ceiling

3"[75mm]

or more

WARNING

Ensure that the intake air will not contain any of the contaminants in Table 2. Contaminated air will damage

the heater, resulting in possible substantial property damage, severe personal injury, or death. For example,

do not pipe intake air near a swimming pool or laundry facilities. These areas always contain contaminants.

Products to Avoid Areas Likely to Have Contaminants

Spray cans containing

uorocarbons Refrigerant leaks Dry cleaning / laundry areas and

establishments Auto body shops

Permanent wave solutions Paint or varnish removers Swimming pools Plastic manufacturing plants

Chlorinated waxes / cleaners Hydrochloric or Muriatic acid Metal fabrication plants Furniture renishing areas

and establishments

Chlorine-based swimming

pool chemicals Cements and glues Beauty shops New building construction

Calcium chloride used for

thawing Refrigeration

Antistatic fabric softeners used in

clothes dryers Refrigeration repair shops Remodeling areas

Sodium chloride used for

water softening

Chlorine-type bleaches, laundry

detergents, and cleaning solvents Photo processing plants Garages and workshops

Adhesives used to fasten

DAMAGE TO THE HEATER CAUSED BY EXPOSURE TO CORROSIVE VAPORS IS NOT COVERED BY

WARRANTY.

(Refer to the limited warranty for complete terms and conditions.)

CAUTION

This water heater is designed to automatically prevent freezing to temperatures of 5

°F

(-15

°C

This freeze protection is not effective if the power fails. In order for freeze protection

to operate, the water heater must have electrical power, gas, water and the main switch must be on.

CAUTION

Freeze Protection

Note:

Damages resulting from incorrect installation or from use of products not approved by the manufacturer

ARE NOT covered by warranty.

[ Table 2 ]

puzpklGjvyuly

kl{hps

}lu{G{lytpuhs hpyGz|wwsGpusl{ hylhG~olylG{lytpuhs

pzGuv{Gwlytp{{lk

m

j

v

m

j

v

Clearance Requirements from Vent Terminations to Building Openings

US Installations¹ Canadian Installations²

A =

Clearance above grade, veranda, porch, deck or

balcony 12 in (30 cm) 12 in (30 cm)

B =

Clearance to window or door that may be opened 4 feet (1.2 m) below or to side of opening;

1 ft (30cm) above opening

6 in (15 cm) for appliances ≤ 10,000

Btuh (3 kw), 12 in (30 cm) for

appliances > 10,000 Btuh (3 kw) and

≤ 100,000 Btuh (30 kw), 36 in (91 cm)

for appliances > 100,000 Btuh (30 kw)

C =

Clearance to permanently closed window

* *

D =

Vertical clearance to ventilated soft located above

the terminal within a horizontal distance of

2 ft (610 cm) from the center line of the terminal

* *

E = Clearance to unventilated soft * *

F = Clearance to outside corner * *

G = Clearance to inside corner * *

H = Clearance to each side of center line extended above

meter / regulator assembly * *

I = Clearance to service regulator vent outlet *

Above a regulator within 3 ft (91 cm)

horizontally of the vertical center line of

the regulator vent outlet to a maximum

vertical distance of 15 ft (4.5 m)

J =

Clearance to nonmechanical air supply inlet to

building or the combustion air inlet to any other

appliance

4 ft (1.2 m) below or to side of opening;

1 ft (30 cm) above opening

6 in (15 cm) for appliances ≤ 10,000 Btuh

(3 kw), 12 in (30 cm) for appliances

> 10,000 Btuh (3 kw) and ≤ 100,000 Btuh

(30 kw), 36 in (91 cm) for appliances

> 100,000 Btuh (30 kw)

K = Clearance to a mechanical air supply inlet 3 ft (91 cm) above if within 10 ft (3 m)

horizontally 6 ft (1.83 m)

L = Clearance above paved sidewalk or paved driveway

located on public property 7ft (2.13 m) 7 ft (2.13 m)

†

M = Clearance under veranda, porch, deck or balcony * 12 in (30 cm)

‡

In accordance with the current ANSI Z223.1/NFPA 54 Natural Fuel Gas Code

In accordance with the current CSA B149.1, Natural Gas and Propane Installation Code

† A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family dwellings and serves both dwellings.

‡ Permitted only if veranda, porch, deck or balcony is fully open on a minimum of two sides beneath the oor. Lennox recommends avoiding this

location if possible.

＊Clearance in accordance with local installation codes and the requirements of the gas supplier. Clearance to opposite wall is 24 in (60 cm).

Installing the Outdoor Enclosure

4. Install the Exhaust Pipe Stopper using 2 screws

(re-use the 2 screws that were removed in Step

1), securing the Exhaust Pipe in place.

2. Insert the VCK Exhaust Adapter and secure the

front 2 screws (re-use the 2 screws that were

removed in Step 1)

1. Remove the Existing Exhaust Adapter by removing

the 4 screws and pulling up on the adapter.

Existing Exhaust

Adapter

Phillips

VCK

Exhaust

Adapter

Exhaust Pipe Stopper

3. Insert the Exhaust Pipe into the VCK Exhaust

Adapter.

Exhaust Pipe

Remove

Loosen

5. Use a Phillips screwdriver to loosen front 2 hex

head screws and to remove back 2 hex head

screws on side of the unit. Place the Outdoor Vent

Cap on the unit. Make sure packing applied inside

of the Outdoor Vent Cap.

7. Insert the Vent Screen into the Exhaust Pipe and

secure with 2 screws [⑧Truss Head Tapping

Screw (M4 x16)] to the Outdoor Vent Cap.

Vent Screen

6. Use a Phillips screwdriver to tighten the 4 screws

[⑦Hexagon Head with Flange Tapping Screw (M4

x12)] to secure the Outdoor Vent Cap.

Detail Detail

Outdoor Vent Cap

Do not overtighten. Use hand screwdrivers only.

CAUTION

1) Turn off the power to the control panel. Press and hold

the ‘Function Button’ to enter the ‘Installer Mode’ 2) In 'Installer Mode', turn the dial button clockwise until

the display reads [14:od].

3) Press the 'Dial Button' so 'oFF' is ashing.

(Default

setting is 'oFF' and outdoor vent function is not activated.)

4) Turn the 'Dial Button' clockwise so 'on' is ashing.

(This will active the Outdoor Vent function.)

8. Setting

5) Press the 'Dial Button' to save the current setting mode

and return back to ‘Installer Mode’.

Inhaltsverzeichnis

Andere Noritz Boiler Handbücher

Noritz

Noritz proTOUGH NR981-SV Bedienungsanleitung

Noritz

Noritz NRC111-SV Bedienungsanleitung

Noritz

Noritz ecoTOUGH NRC711-DV Bedienungsanleitung

Noritz

Noritz NR66-SV Bedienungsanleitung

Noritz

Noritz ProTough BNR98-DVC-LP Bedienungsanleitung

Noritz

Noritz N-0751M-OD Bedienungsanleitung

Noritz

Noritz N-0751M-OD Bedienungsanleitung

Noritz

Noritz GQ-C3257WZ-FF US Bedienungsanleitung

Noritz

Noritz ecoTOUGH NRC711-DV Bedienungsanleitung

Noritz

Noritz NC1991-OD-LP Bedienungsanleitung

Noritz

Noritz GQ-C3260WXQ-FF US Bedienungsanleitung

Noritz

Noritz N-0751M Bedienungs- und Wartungshandbuch

Noritz

Noritz GQ-2457WS US Bedienungsanleitung

Noritz

Noritz N-132 Programmierhandbuch

Noritz

Noritz proTough NR98SV Bedienungsanleitung

Noritz

Noritz ecoTOUGH NRC71 OD Bedienungsanleitung

Noritz

Noritz THERMALUX NERC98DV Bedienungsanleitung

Noritz

Noritz NR83-DVC Bedienungsanleitung

Noritz

Noritz N-0931M-OD Bedienungsanleitung

Noritz

Noritz N-132M-ASME Bedienungsanleitung

Noritz

Noritz EZ98DV Bedienungsanleitung

Noritz

Noritz NC1991-OD-NG Bedienungsanleitung

Noritz

Noritz N-0751M-DVC Bedienungsanleitung

Noritz

Noritz N-0751M Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

Applimo

Applimo Edel AIR Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung