Novus NVIP-2DN3033V/IR-1P-II Bedienungsanleitung

U ser’s manual

( short form)

NVIP-2DN3033V/IR-1P-II

NVIP-2DN3033V/IR-1P-II - User’s manual (short form) ver 1.0

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2014/30/UE) and LVD (2006/95/EC ) Directives

CE Marking

Our products are manufactured to comply with requirements of the following directives and

national regulations implementing the directives:

Electromagnetic compatibility EMC 2014/30/UE.

Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical equipment

designed for use with a voltage rating of between 50VAC and 1000VAC as well as 75VDC and

1500VDC.

WEEE Directive 2012/19/EU

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European 1000VAC Directive on Waste Electrical

and Electronic Equipment (2002/96/EC) and further amendments. By ensuring this product is

disposed of correctly, you will help to prevent potential negative consequences for the

environment and human health, which could otherwise be caused by inappropriate waste

handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance

may not be treated as household waste. It shall be handed over to the applicable collection point for

used up electrical and electronic equipment for recycling purpose. For more information about

recycling of this product, please contact your local authorities, your household waste disposal service

or the shop where you purchased the product.

RoHS Directive 2011/65/EU

Out of concern for human health protection and friendly environment, we assure that our

products falling under RoHS Directive regulations, regarding the restriction of the use of

hazardous substances in electrical and electronic equipment, have been designed and

manufactured in compliance with the above mentioned regulations. Simultaneously, we

claim that our products have been tested and do not contain hazardous substances whose

exceeding limits could have negative impact on human health or natural environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed

for self installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other

devices during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE

GIVEN PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED

WITH THE PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL

APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE CONTACTED

UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY

FOR THE RESULTS OF SUCH AN ACTION.

NVIP-2DN3033V/IR-1P-II - User’s manual (short form) ver 1.0

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO

USER-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE

PERSONNEL MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and

operating instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual

is necessary.

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the

user’s manual.

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is

forbidden.

7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools,

bath tubs, damp basements).

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.)

is not recommended since it may lead to heat build-up and damaging the device itself as a

consequence.

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden.

Improperly mounted camera may cause a fatal accident or may be seriously damaged itself. The

camera must be mounted by qualified personnel with proper authorization, in accordance with this

user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with

those specified by the producer in the camera technical datasheet. Therefore, it is forbidden to

supply the camera from a power sources with unknown parameters, unstable or not meeting

producer’s requirements.

Due to the product being constantly enhanced and optimized, certain parameters and functions

described in the manual in question may change without further notice.

We strongly suggest visiting the www.novuscctv.com website in order to access the newest manual.

NVIP-2DN3033V/IR-1P-II - User’s manual (short form) ver 1.0

TABLE OF CONTENTS.................................................................................................4

1. FOREWORD INFORMATION..................................................................................5

1.1. General characteristics .....................................................................................5

1.2. Technical specification ....................................................................................6

1.3. Camera dimension ...........................................................................................7

1.4. Package contents..............................................................................................7

2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................8

2.1. Description of connectors and control tools ......................................................8

2.2. Cameras mounting ...........................................................................................9

2.3. Desiccant mounting guide ..............................................................................10

2.4. Starting the IP camera ....................................................................................10

2.5. Initial configuration via the web browser........................................................12

3. NETWORK CONNECTION UTILIZING WEB BROSWER ...............................13

3.1. Recommended PC specification for web browser............................................13

3.2. Connection with IP camera via web browser...................................................13

4. USING AND CONFIGURING..................................................................................15

4.1. Displaying live pictures...................................................................................15

5. ELECTRIC CONNECTORS AND ACCESORIES ...............................................16

5.1. Connecting power supply to the camera. ........................................................16

5.2. Connecting audio input ..................................................................................16

6. RESTORING FACTORY DEFAULTS ..................................................................17

6.1. Restoring software factory defaults .................................................................17

6.2. Restoring hardware factory defaults in IP cameras .........................................17

TABLE OF CONTENTS

NVIP-2DN3033V/IR-1P-II - User’s manual (short form) ver 1.0

1. FOREWORD INFORMATION

1.1. General Characteristics

 Imager resolution: 2.0 megapixels

 Mechanical IR cut filter, IR operation capability

 Min. Illumination from 0 lx with IR LED on

 Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions

 Digital Noise Reduction (DNR)

Lens type: varifocal, f= 2.8mm/F=1.6

 Built-in LED illuminator: 10 pcs LED

 Compression: H.264, H2.65/ MJPEG

 Max video processing resolution: 1920 x 1080

 Multi streaming: compression, resolution, speed and quality defined individually for each video

stream

 ROI functions

 Private Zones

 RTP/RTSP protocol support for video transmission

 Post-alarm functions

 Audio input

 BNC output

 Built-in webserver: camera configuration through the website

 Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server

 Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,

playback and remote IP devices administration

 Video Content Analysis (VCA):

Exception

Line Crossing

Intrusion

 Power supply: 12VDC, PoE (Power over Ethernet)

FOREWORD INFORMATION

NVIP-2DN3033V/IR-1P-II - User’s manual (short form) ver 1.0

1.2. Technical specification

FOREWORD INFORMATION

IMAGE

Image Sensor 2 MPX CMOS sensor 1/2.7” APTINA

Number of Effective Pixels 1920 (H) x 1080 (V)

Min. Illumination 0.09 lx/F1.6 - color mode,

0 lx (IR on) - B/W mode

Electronic Shutter auto: 1/25 s ~ 1/100000 s

Wide Dynamic Range (WDR) yes

Digital Noise Reduction (DNR) 3D

Defog Function (F-DNR) yes

LENS

Lens Type standard, f=2.8 mm/F1.6

DAY?NIGHT

Switching Type mechanical IR cut filter

Switching Mode auto, manual, time

Switching Level Adjustment yes

Switching Schedule yes

Visible Light Sensor yes

NETWORK

Stream Resolution 1920 x 1080 (Full HD), 1280 x 720 (HD), 640 x 480 (VGA), 320 x 240 (QVGA)

Frame Rate 30 fps for 1920 x 1080 (Full HD) and lower resolutions

Multistreaming Mode 3 streams

Video/Audio Compression H.264, H.265, MJPEG/G.711

Number of Simultaneous Connections max. 4

Bandwidth 9 Mb/s in total

Network Protocols Support TCP/IP, UDP, FTP, DHCP, DDNS, NTP, RTSP, UPnP, PPPoE, SMTP

ONVIF Protocol Support Profile S (ONVIF 2.3)

Camera Configuration from Internet Explorer, Firefox, Chrome, Opera browser

languages: Polish, English, Russian, and others

Compatible Software NMS

OTHER FUNCTIONS

Privacy Zones 4

Motion Detection yes

Region of interest (ROI) 8

Image Processing 90˚ image rotation, 180˚ image rotation, sharpening, mirror effect

Prealarm/Postalarm -/up to 240 s

System Reaction to Alarm Events e-mail with attachment, saving file on FTP server

IR LED

LED Number 10

Range 20 m

Angle 90°

INTERFACES

Video Output BNC, 1.0 Vp-p, 75 Ohm - maintenance only

Audio Input/Output 1 x Jack (3.5 mm)/-

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

INSTALLATION PARAMETERS

Dimensions (mm) 108 (Ф) x 90 (H)

Weight 0.45 kg

Degree of Protection IP 66 (details in the further part of the manual)

Enclosure vandal proof aluminium, white

Power Supply PoE, 12 VDC

Power Consumption 2 W, 4 W (IR on)

Operating Temperature -30°C ~ 50°C

NVIP-2DN3033V/IR-1P-II - User’s manual (short form) ver 1.0

FOREWORD INFORMATION

1.3. Camera dimensions

1.4. Package contents

After you open the package make sure that the following elements are inside:

 IP camera

 Accessories bag

 Short version of user’s manual

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches

the temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

87 mm

108 mm

90 mm

NVIP-2DN3033V/IR-1P-II - User’s manual (short form) ver 1.0

START-UP AND INITIAL IP CAMERA CONFIGURATION

2. START-UP AND INITIAL IP CAMERA CONFIGURATION

2.1 View of the camera, layout of the camera items

1. BNC output

2. Audio input (MIC)

3. Power supply 12VDC

4. 100 Mb/s Ethernet port (RJ-45 hermetic connector)

5. Screws locking camera base

6. IR LED

7. Day/night sensor

NVIP-2DN3033V/IR-1P-II - User’s manual (short form) ver 1.0

2.2. Connecting ethernet cable

To maintain tightness of ethernet cable connection, please follow instruction below:

1. Loosen the nut (a) from the main element (b).

2. Run power cable (without RJ-45 connector) though both elements. Then crimp the cable with RJ-45

connector.

3. Connect the cable to the hermetic connector (c), screw main cover (b), then screw the nut (a).

WARNING! 12VDC power connector and others are not hermetic. User should seal power connector

by himself.

5.1. Connecting power supply to the camera.

Camera can be supplied using external power supply unit corresponding with the camera parameters or

by using RJ45 network socket and PoE (802.3at Type 1 ) power supply unit.

Information:

Power supply adapter is not included. Please use power adapter with parameters specified in user’s

manual.

Caution:

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.) not compatible

with IEEE 802.3af standard (items called “passive PoE power supply”). Damages that results from the

usage of improper power supply source are not covered by the warranty

START-UP AND INITIAL IP CAMERA CONFIGURATION

a b

12 VDC +

12 VDC -

Camera 12 VDC power supply

NVIP-2DN3033V/IR-1P-II - User’s manual (short form) ver 1.0

2.3. Installation

1. Remove locking screws from camera base and then remove camera base.

2. Use the included mounting template or the camera base plate to mark holes for mounting

screws.

3. Drill mounting and cable holes in previously selected points.

4. Mount the camera base using screws on smooth surface providing declared degree of IP

protection.

5. Mount camera to camera base and screw locking screw.

6. Adjust the position of the camera module. If required, loosen the screws blocking camera

module.

CAUTION!!!

The declared degree of protection of the camera relates to its housing and does not take into

account the possibility of moisture infiltration into the interior of the camera by connecting

cables. Connection cables protection through i.e. sealing up is the responsibility of the camera

installer. The manufacturer is not liable for any damages to the camera caused as a result of

failing in performing that activity by installer, which also means that camera damaged in that

way is not subject to warranty repairs

START-UP AND INITIAL CAMERA CONFIGURATION

Inhaltsverzeichnis

Sprachen:

Andere Novus Sicherheitskamera Handbücher

Novus

Novus NVIP-2VE-6232 Bedienungsanleitung

Novus

Novus NVC-401D Bedienungsanleitung

Novus

Novus NVAHD-2DN5202MH/IR-1 Bedienungsanleitung

Novus

Novus NVIP-4H-6532M/F-II Bedienungsanleitung

Novus

Novus NVIP-5000 series Bedienungsanleitung

Novus

Novus NVIP-2DN5001D/IR-1P Bedienungsanleitung

Novus

Novus NVIP-2DN3037V/IR-1P Bedienungsanleitung

Novus

Novus 4000 series Bedienungsanleitung

Novus

Novus NVIP-5H-4202M Bedienungsanleitung

Novus

Novus NVIP-2VE-6202 Bedienungsanleitung

Novus

Novus NVIP-5DN7021D/IR-2P Bedienungsanleitung

Novus

Novus NVIP-4VE-6202-II Bedienungsanleitung

Novus

Novus NVIP-5DN3615AV/IR-1P/F Bedienungsanleitung

Novus

Novus NVIP-2V-6402M Bedienungsanleitung

Novus

Novus NVIP-8H-6402M/F Bedienungsanleitung

Novus

Novus NHDC-5VE-5101 Bedienungsanleitung

Novus

Novus NVDN-401H/IR Bedienungsanleitung

Novus

Novus NVIP-5H-6202 Bedienungsanleitung

Novus

Novus NVIP-2DN5021H/IRH-1P Bedienungsanleitung

Novus

Novus NVIP-1DN3000H/IR-1P Bedienungsanleitung

Novus

Novus NVIP-4DN2001H/IR-1P Bedienungsanleitung

Novus

Novus NVIP-2VE-6231/WL-II Bedienungsanleitung

Novus

Novus NVIP-2DN5120SD/IRH-2 Bedienungsanleitung

Novus

Novus NVIP-2VE-6501/F Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung