Numark NS6 Bedienungsanleitung

SPECIFICATION

FUNCTION

1. POWER IN – Use the included power cable to connect NS6 to a power outlet. While the power is switched off, plug the

cable into NS6 first, then plug the cable into a power outlet.

2. POWER SWITCH – Turns NS6 on and off. Turn on NS6 after all input devices have been connected and before you

turn on amplifiers. Turn off amplifiers before you turn off NS6.

3. USB – This USB connection sends and receives audio and control information from a connected computer.

4. MASTER OUTPUT (XLR) – Connect this low-impedance XLR output to a PA system or powered monitors. The level

of this output is controlled with the MASTER knob on the top panel.

5. MASTER OUTPUT (RCA) – Use standard RCA cables to connect this output to a speaker or amplifier system. The

level of this output is controlled by the MASTER knob on the top panel.

6. BOOTH/ZONE OUTPUT (RCA) – Use standard RCA cables to connect this output to a booth monitoring system. The

level of this output is controlled by the BOOTH/ZONE knob on the top panel.

7. LINE INPUTS (RCA) – Connect line-level devices, such as CD players, samplers or audio interfaces, to these inputs.

8. MIC INPUT (1/4") – Connect a 1/4" microphone to this input. Microphone controls are located on the top panel.

9. LINE | PHONO INPUTS (RCA) – Connect your audio sources to these inputs. These inputs can accept both line and

phono-level signals.

10. LINE | MIC SWITCH – Flip this switch to the appropriate position, depending on the device connected to the LINE |

PHONO INPUTS. If you are using a microphone, set this switch to "MIC." If using a line-level

device, such as a CD player or sampler, set this switch to "LINE."

11. LINE | PHONO SWITCH – Flip this switch to the appropriate position, depending on the device connected to the

LINE | PHONO INPUTS. If you are using phono-level turntables, set this switch to

"PHONO" to provide the additionalamplification needed for phono-level signals. If using a

line-level device, such as a CD player or sampler, set this switch to "LINE."

12. GROUNDING TERMINAL – If using phono-level turntables with a grounding wire, connect the grounding wire to

these terminals. If you experience a low “hum” or “buzz”, this could mean that your

turntables are not grounded.

13. HEADPHONES – Connect your 1/4" or 1/8" headphones to this output for cueing and mix monitoring.

14. HEADPHONE VOLUME – Adjusts the volume level of the headphone output.

SERVICE MANUAL

MODEL:NS6

15. SPLIT CUE – When this switch is in the ON position, the headphone audio will be "split" such that all channels sent to

CUE are mixed to mono and applied to the left headphone channel and the Program mix is mixed to

mono and applied to the right channel. When the switch is in the OFF position, Cue and Program audio

will be "blended" together.

16. CUE BLEND – Turn to mix between Cue and Program in the Headphone channel. When all the way to the left, only

channels routed to CUE will be heard. When all the way right, only the Program mix will be heard.

17. CROSSFADER ASSIGN – Routes the audio playing on the corresponding channel to either side of the crossfader (L

or R), or bypasses the crossfader and sends the audio directly to the Program Mix

(center, "|").

18. CROSSFADER SLOPE – Adjusts the slope of the crossfader curve. Turn the knob to the left for a smooth fade

(mixing) or to the right for a sharp cut (scratching).

19. FADER START – Enables or disables “fader start” on the corresponding side of the crossfader. When fader start is

enabled on one side, moving the crossfader toward that side will cause the Deck to start playing.

STANDARD

1.MaxMSP test program for production Line

2. AP test specification

RCA Balance Output

Voltage AC 100V~240V 50~60Hz

MASTER:2

0.5V

Volume BOOTH:2

0.5V

BALANCED:12

Distortion defection 0.03% below

S/ N 70dBr upward

Separation 70dBr upward

F/R 20~20KHz

0.5dB

DISASSEMBLY PROCEDURES

1. REMOVAL OF BOTTOM CHASSIS. (Fig1)

(A) TAKE OUT THE 21 PCS SCREWS FROM THE BOTTOM CHASSIS.

Fig.1

2.REMOVAL HEADPHONE PCB AND DOUSER ASSEMBLY AND XLR JACK ASSEMBLY. (Fig2)

(A) TAKE OUT THE 3 PCS KNOB.

(B) TAKE OUT THE 9 PCS SCREWS

，

TAKE OUT THE 1 PC NUT HOLDER AND TAKE OUT THE 2 PCS

CONNECTORS.

(D) TAKE OUT THE 6 PCS SCREWS

，

TAKE OUT THE 2 PCS CONNECTORS AND TAKE OUT THE 2 PCS

DOUSER ASSEMBLY.

(E) TAKE OUT THE 4 PCS SCREWS FROM THE XLR JACK ASSEMBLY.

(F) TAKE OUT THE 5 PCS SCREWS

，

TAKE OUT THE 2 PCS NUT HOLDER AND TAKE OUT THE 2 PCS

CONNECTORS.FROM THE AN PCB.

Fig.2

DISASSEMBLY PROCEDURES

3. REMOVAL OF CROSS FADER ASSEMBLY AND KNOB. (Fig3)

(A) TAKE OUT THE 1 PC KNOB FROM THE PANEL.

(B) TAKE OUT THE 2 PCS SCREWS AND 1 PC CONNECTORS FROM THE PANEL.

Fig.3

. REMOVAL OF MIXER PCB AND LEFT PCB.(Fig )

(A) TAKE OUT THE 23 PCS SCREWS AND 6 PCS CONNECTORS FROM THE MIXER PCB.

(B) TAKE OUT THE 16 PCS SCREWS AND 3 PCS CONNECTORS FROM THE LEFT PCB

Fig.

LEVEL P/N DESCRIPTION QTY REF

0.1 AL4-71-0016 CABLE USB RF CHOKE 2.0 1

0.1 AL7-10-1215 ADAPTOR 12V2.0A 24W (01) 1

AL7-40-0062 ADAPTOR 12VDC/2A (EU) (02)

AL7-40-0063 ADAPTOR 12VDC/2A (UK) (03)

AL7-40-0064 ADAPTOR 12VDC/2A (AUS) (04)

AL7-10-1215 ADAPTOR 12V2.0A 24W (07)

0.1 CB300WMAR25 CD Sleeve 1

0.1 CN0220001006 Flat Cable GND Wire Black Longth 100mm φ3.2 Fenale 1

0.1 CN0425001006 4Pin Pitch 2.5mm Single Row Length 100mm 1 86

0.1 EVA1104415 EVA 1 87

0.1 FFC2610001002 FFC 26Pin Pitch 1.0mm Length:100mm 5 67

0.1 LAC22MAR403 S/N BAR CODE LABEL 1 81

0.1 LAC57MAR659 Safety Label 1 83

0.1 LAC62MAR404 BAR CODE LABEL 2

0.1 LAC62MAR631 Label(date) 1 82

0.1 LAC62MAR667 BAR Code Label (CODE 39) 1

0.1 LAC67MAR680 Label (FSR) 2 41

0.1 LAC67MAR681 Label 3

0.1 LAC67YAH261 Sticker φ8mm Green 1

0.1 MT0705517 COPPER 2 51

0.1 MT1101838 Ground Plate 2 45

0.1 MT112047102 FRONT PANEL PRINTING 1 68

..2 MT112047101 FRONT PANEL PAINTING 1

...3 MT1120471 FRONT PANEL 1

0.1 MT112047202 REAR PANEL PRINTING 1 59

..2 MT112047201 REAR PANEL PAINTING 1

...3 MT1120472 REAR PANEL 1

0.1 MT1120477 Power Button Cover 1 70

0.1 MT113008301 Panel(Anodizeing + Printing) 1 7

0.1 MT113009201 Panel(CROSS FADER)Anodizeing+Printing 1 9

0.1 MT113034901 Bottom Chassis Painting 1 64

0.1 MT5105509 COPPER SPINDLE 2 44

0.1 NM1104412 VELVET CARPET 15 60

0.1 NM1104417 VELVEV CARTPET 2 49

0.1 NM1104438 VELCRO 1 102

0.1 NM1106129 Velvet Carpet 2 48

0.1 NM1106130 Velvet Carpet 4 47

0.1 NM1106131 Conducti Fabric 2 99

0.1 NP211MAR140 Display Plate 1 5

0.1 NP211MAR142 Name Plate 1 34

0.1 NP211MAR148 Name Plate 1 35

0.1 NP311MAR141 Wheel Plate 2 38

0.1 NUT01030IID Nut 5 94

0.1 NUT05030ICU Nut 1 96

0.1 OTFSR5K Force Sensing Resistor 2 98

0.1 PNK18MAR01 PACKAGE ASS'Y 1

..2 BC1015011050 Bubble Pad 1

..2 CGNK18513MAR01 Inner Box 1

..2 CTNK18513MAR01 CARTON 1

..2 NM1104430 Velvet Carpet 1

..2 NM1104439 VELCRO 1

..2 OPNK14MAR06 Operation Manual 1

..2 OPNK18MAR01 INSTRUCTION BOOK 1

..2 PE230370402B07 Poly Bag 230*370mm 1

..2 PLNK1801 POLYFOAM (LEFT) 1

..2 PLNK1802 POLYFOAM (RIGHT) 1

..2 SD850850 SOFT SHEET 1

0.1 PT0710620801 KNOB 1 2

0.1 PT0710621101 KNOB 3 69

0.1 PT0710624609 Button(ON/OFF)Printing 2 14

..2 PT07106246 KNOB 2

NK18MAR01~07 BOM

0.1 PT0710624610 Button Printing 2 16

..2 PT07106246 KNOB 2

0.1 PT0710624611 Button(DELETE) Printing 2 21

..2 PT07106246 KNOB 2

0.1 PT0710624612 Button(3~5)Printing 2 22

..2 PT07106246 KNOB 2

0.1 PT0710624613 Button(CRATES)Printing 1 30

..2 PT07106246 KNOB 1

0.1 PT0710624614 Button(LOAD A)Printing 1 31

..2 PT07106246 KNOB 1

0.1 PT0710624714 Button(FX A)Printing 1 32

..2 PT07106247 KNOB 1

0.1 PT0710624715 Button(FX B)Printing 1 33

..2 PT07106247 KNOB 1

0.1 PT0710624716 Button(LAYER)Printing 2 36

..2 PT07106247 KNOB 2

0.1 PT0710624801 KNOB(CUE) 2 24

..2 PT07106248 KNOB 2

0.1 PT0710624808 Button(Dll)Printing 2 23

..2 PT07106248 KNOB 2

0.1 PT0710624809 Button(SYNC)Printing 2 25

..2 PT07106248 KNOB 2

0.1 PT1104416001 Side Cap PAINTING SOFT TOUCH 2 63

..2 PT11044160 Side Cap 2

0.1 PT1104416101 Plastic Bezels Paiting 2 46

..2 PT11044161 Plastic Bezels 2

0.1 PT11044162 FIXED HOLDER(FSR) 2 88

0.1 PT1110612401 VR KNOB PAINTING ABS+TPR 2 6

0.1 PT1110613601 KNOB 18 3

0.1 PT1110613701 KNOB 4 1

0.1 PT11106151 POWER BUTTON 1 61

0.1 PT11106163 VR KNOB 5 8

0.1 PT11106178 VR KNOB PAINITING ABS+ABS 2 4

0.1 PT1110619641 Button TAP Printing 2 11

..2 PT11106196 KNOB 2

0.1 PT1110619642 Button(SCRATCH)Painting 2 18

..2 PT11106196 KNOB 2

0.1 PT1110625501 Button(1/2X)Printing 2 13

..2 PT11106255 Button 2

0.1 PT1110625502 Button(1/2X)Printing 2 15

..2 PT11106255 Button 2

0.1 PT1110625601 Button(BACK)Printing 1 28

..2 PT11106256 Button 1

0.1 PT1110625602 Button(FWD)Printing 1 29

..2 PT11106256 Button 1

0.1 PT11106275 Lid (FSR) 2 54

0.1 PT11106276 Lid 2 53

0.1 PT11106283 Light Pipe 6 42

0.1 PT1110628401 Button(A.B)Printing 5 12

..2 PT11106284 Button(Circuler) 5

0.1 PT1110628402 Button(Circuler)Printing 2 27

..2 PT11106284 Button(Circuler) 2

0.1 PT1110628701 Button (+,-)(Printing) 2 26

..2 PT11106287 Button 2

0.1 PT11106290 Lid 1 89

0.1 PT11106306 Lid 2 20

0.1 PT11106307 Lid 4 19

0.1 PT1110631601 Buttom Painting 9 17

..2 PT11106316 Buttom 9

0.1 PT1110631602 Buttom Painting 4 37

..2 PT11106316 Buttom 4

0.1 PT1110730 Wheel Frame 2 40

..2 MT1105543 Wheel Plate Axis 2

0.1 PT111073401 Wheel Frame Painting 2 39

..2 PT1110734 Wheel Frame 2

0.1 PT1130209 TOP HOUSING 1 50

0.1 PU008008001 Pu Foam 2 91

0.1 PU010010010 QUARANTINE CLOTH 3 84

0.1 PU014006006 Qurantine Cloth 1 101

0.1 RN109111 FIXED RING 2 52

0.1 RU0730605 RUBBER FOOT 6 65

0.1 SC0305FA2IBI Screw M3X5 HFB 4 75

0.1 SC0305PIBI SCREW M3X5 PPB 7 80

0.1 SC0308ABBI Screw(FLAT) 34 74

0.1 SC0308ABNI Screw 21 79

0.1 SC0308AINI Screw 8 78

0.1 SC0308FIBNI Screw M3*8 PFB W/NYLOC 4 97

0.1 SC0308RBNI SCREW M3X8 PRN TAPPING 50 77

0.1 SC0314PMJI Screw M3X14 PPN 1 92

0.1 SC2605RBNI SCREW M2.6X5 PPN TAPPING 14 76

0.1 TSNK18 CD 1

0.1 TWNP632YAH10601 Douser Assembly 2

..2 MT321004001 DOUSER PLATE FIXED BASE 2 73-1

..2 MT3210070 PLATE 4 73-3

..2 NP632YAH106 DOUSER 2 73-4

..2 RN0416001 CS RING 2 73-5

..2 SC0303SIBI SCREW M3X3 HXB 2 73-2

0.1 WR0620001001 Isolation Cable 6Pin Single Row Pitch 2.0mm Length 1

185

0.1 WR0620003001 Isolation Cable 6Pin Single Row Pitch 2.0mm Length 3

190

0.1 WS073307IC Washer Flat 3 93

0.1 WS113008204IB Washer 2 43

0.1 WS663309IC Spring Washer 3# 1 95

0.1 AL9-79-0573 AN PCB ASS'Y 1

..2 AL9-40-0573 AN PCB 1

..2 AL9-79-0573A01 AN PCB ASS'Y 1 62

...3 AA822757X TRANSISTOR 2SC3326 NPN 12 Q1~8,13~16

...3 AL0-17-0103 RESISTOR ARRAY 4X10K 1/10W 0603 3 R41,42,219

...3 AL0-17-0470 RESISTOR ARRAY 4X47 1/10W 0603 6 R181,192,209,212,225,226

...3 AL1-08-0474 Capacitor Electrolytic 47uF/16V 5*11mm 1 C208

...3 AL2-50-4149 Diode Single 1N4148 100V 200mA SOT-23 2 D4,7

...3 AL2-51-0340 DIODE POWER SCHOTTKY MBRA340T3 40V 3A SM 7 D2,5,6,8,12,16,17

...3 AL2-51-4401 TRANSISTOR 2N4401 NPN 2 Q10,19

...3 AL2-51-4403 TRANSISTOR 2N4403 PNP 3 Q9,11,17

...3 AL2-54-6306 Mosfet FDC6306P P-CH SSOT-6 1 Q18

...3 AL2-61-0431 REG LM431 2.5V-37V 100MA 2% SOT-23 1 U32

...3 AL2-61-5000 IC REG VOLTAGE NCP500SN25T1 2.5V SOT23-5 1 U30

...3 AL2-63-0126 IC SINGLE BUS BUFFER GATE WITH SN74AHCT1G1 1 U27

...3 AL2-71-3079 IC MC33079 QUAD OP-AMP SOP-14 3 U3,6,11

...3 AL2-74-0181 IC OPTO-ISOLATOR TLP181 TRANS-OUT SMD 1 SEN1

...3 AL4-02-0007 JACK 1/4 STEREO 7-PIN FEM MINI W/GRND LUG STRAI

2 J1,5

...3 AL4-08-0402 Con USB 4-Pin Female PC-MNT Horizontal 1 J11

...3 AL7-01-0046 Crystal 12MHZ 49US SMD Fundamental 1 X1

...3 AL7-20-0067 INDUCTOR 33uH 1.8A SMD 1 L7

...3 AL7-20-0087 Inductor 15uH 2.3A ±15% 10.5×9.0mm DIP 1 L4

...3 CS101J5003NPO CERAMIC 100pF/50V 5% 0603 NPO 32 C4~16,18,19,23,30,31,34,35,57,60,64,73,91,100,106,1

10,154,159,163,167

...3 CS102J5003NPO CERAMIC 1nF/50V 5% 0603 NPO 6 C63,74,105,111,162,168

...3 CS103K2502X7R CERAMIC 0.01UF/25V 10% 0402 X7R 14 C3,92,95,148,160,175,204~206,209,210,219,221,225

...3 CS104K2502X5R CERAMIC 0.1UF/25V 10% 0402 X5R 90

C1,2,20,29,38,39,45~52,54,62,67,72,75~77,84,86,88,9

3,94,96~98,102,103,109,113,115,116,118,120,121,125

~129,131,132,134,136,139,140,142,144,145,147,149~

151,156,157,161,166,170,176,177,184~188,192,193,1

95,196,199,200,203,207,211~216,220,222,226,227,23

1,236~238

...3 CS104K5003X7R CERAMIC 0.1uF/50V 10% 0603 X7R 12 C40,41,79,124,158,164,172,178,189,R188,252,257

...3 CS105K1003X5R CERAMIC 1uF/10V 10% 0603 X5R 12 C21,114,117,141,155,183,194,218,223,228,229,230

...3 CS152J5003NPO CERAMIC 1500PF/50V 5% 0603 NPO 4 C42,43,55,56

...3 CS180J5003NPO CERAMIC 18pF/50V 5% 0603 NPO 6 C22,69,101,119,122,123

Andere Handbücher für NS6

Inhaltsverzeichnis

Andere Numark DJ-Equipment Handbücher

Numark

Numark DJio Bedienungsanleitung

Numark

Numark iCDMIX 2 Bedienungsanleitung

Numark

Numark OMNI CONTROL Gebrauchsanweisung

Numark

Numark MIXTRACK PLATINUM FX Bedienungsanleitung

Numark

Numark NS6 Bedienungsanleitung

Numark

Numark X5 Bedienungsanleitung

Numark

Numark NVII Bedienungsanleitung

Numark

Numark C3 Bedienungsanleitung

Numark

Numark PT01 Scratch Bedienungsanleitung

Numark

Numark MIXTRACK PLATINUM Bedienungsanleitung

Numark

Numark MIX DECK Bedienungsanleitung

Numark

Numark NS6 II Bedienungsanleitung

Numark

Numark NuVJ Bedienungsanleitung

Numark

Numark cdmix usb Bedienungsanleitung

Numark

Numark Mixtrack Quad Bedienungsanleitung

Numark

Numark iDJLIVE Bedienungsanleitung

Numark

Numark MIXSTREAM PRO Bedienungsanleitung

Numark

Numark MixTrack Pro FX Bedienungsanleitung

Numark

Numark iCDMIX 2 Bedienungsanleitung

Numark

Numark Mixtrack Quad Bedienungsanleitung

Numark

Numark MIXSTREAM PRO Bedienungsanleitung

Numark

Numark Mixtrack Pro 3 Bedienungsanleitung

Numark

Numark IDJ PRO Bedienungsanleitung

Numark

Numark Party Mix Pro Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung