NXP Semiconductors UM11650 Bedienungsanleitung

UM11650

KIT-TPLSNIFEVB tool

Rev. 2 — 23 June 2023 User manual

Document information

Information Content

Keywords TPL, ETPL, electrical transport protocol link, decoder, TPL sniffer

Abstract This document helps users understand how to use the KIT-TPLSNIFEVB to acquire ETPL

communications.

NXP Semiconductors UM11650

KIT-TPLSNIFEVB tool

Rev Date Description

2 20230623 •Updated vocabulary throughout the document

•Updated mentions of software decoder available throughout the document

1 20210804 initial version

Revision history

IMPORTANT NOTICE

For engineering development or evaluation purposes only

NXP provides the product under the following conditions:

This evaluation kit is for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES

ONLY.

It is provided as a sample IC pre-soldered to a printed-circuit board to make it easier to access inputs,

outputs and supply terminals. This evaluation board may be used with any development system or

other source of I/O signals by connecting it to the host MCU computer board via off-the-shelf cables.

This evaluation board is not a Reference Design and is not intended to represent a final design

recommendation for any particular application. Final device in an application heavily depends on

proper printed-circuit board layout and heat sinking design as well as attention to supply filtering,

transient suppression, and I/O signal quality.

The product provided may not be complete in terms of required design, marketing, and or

manufacturing related protective considerations, including product safety measures typically found

in the end device incorporating the product. Due to the open construction of the product, it is the

responsibility of the user to take all appropriate precautions for electric discharge. In order to minimize

risks associated with the customers’ applications, adequate design and operating safeguards must be

provided by the customer to minimize inherent or procedural hazards. For any safety concerns, contact

NXP sales and technical support services.

User manual Rev. 2 — 23 June 2023

2 / 15

NXP Semiconductors UM11650

KIT-TPLSNIFEVB tool

1 Introduction

The KIT-TPLSNIFEVB, also called transport protocol link (TPL) sniffer is working with a logic analyzer

(preferably a Saleae logic analyzer) and its software to help analyze electrical transport protocol link (ETPL)

signals.

Figure 1. KIT-TPLSNIFEVB

Placed in any ETPL bus, it non-intrusively listens to all messages and monitors the frame traffic on the bus (the

TPL sniffer works in listen mode only). The corresponding received data [in serial peripheral interface (SPI)

format] is available on the analyzer output connector (see Figure 6), to be connected to a logic analyzer and its

software which provides further analysis of such data.

Additionally, plug-ins and extensions for the Saleae logic analyzer software are available to decode TPL frames.

Visit http://www.nxp.com/KIT-TPLSNIFEVB for additional details.

User manual Rev. 2 — 23 June 2023

3 / 15

NXP Semiconductors UM11650

KIT-TPLSNIFEVB tool

aaa-042711

HARDWARE

SETUP

HARDWARE

SETUP

OPTIONAL

POWER

BANK

HARDWARE

SETUP

Hardware setup without TPL sniffer:

HARDWARE

SETUP

TPL sniffer

KIT-TPLSNIFEVB

COMPUTER

LOGIC

ANALYZER

Two-twisted-wire

ETPL cable

Two-twisted-wire

ETPL cable

Two-twisted-wire

ETPL cable (optional in case

of daisy chain)

ETPL bus

USB cable

With optional:

- Saleae Logic Analyzer Software

- NXP TPL decoder extensions

Micro-USB

port

8-pin connectors cable

Figure 2. TPL sniffer toolchain

Note: This product has not undergone formal EU electromagnetic compatibility (EMC) assessment. As a

component used in a research environment, it is the responsibility of the user to ensure the finished assembly

does not cause undue interference when used and cannot be CE marked unless assessed.

2 Finding kit resources and information on the NXP website

NXP Semiconductors provides online resources for this tool and its supported devices on its website. The

information page for the KIT-TPLSNIFEVB tool provides overview information, documentation, software

and tools, parametrics, ordering information and a Getting Started tab. The Getting Started tab provides

quick‑reference information applicable to using the KIT-TPLSNIFEVB tool, including the downloadable assets

referenced in this document.

2.1 Collaborate in the NXP community

The NXP community is for sharing ideas and tips, ask and answer technical questions, and receive input on just

about any embedded design topic.

User manual Rev. 2 — 23 June 2023

4 / 15

NXP Semiconductors UM11650

KIT-TPLSNIFEVB tool

3 Getting ready

3.1 Kit contents

•Assembled and tested TPL sniffer dongle in anti-static bag

•A logic analyzer connection cable with 8-pin headers

•An ETPL bus connection twisted cable with 2-pin headers

Figure 3. Kit contents

3.2 Additional hardware and software

The TPL sniffer requires only a 5.0 V with 50 mA (average) and 150 mA (peak) power supply through a USB

Micro-B connector (for example, a power bank, or a USB cable connected to a computer).

To analyze the data sourced from the TPL sniffer a logic analyzer (for example, Saleae logic analyzer) is

required along with its software.

Optionally, plug-ins and extensions to add to the Saleae logic analyzer software have been developed in order

to decode TPL frames. For additional details, go to http://www.nxp.com/KIT-TPLSNIFEVB.

4 Getting to know the hardware

4.1 KIT-TPLSNIFEVB features

•Internal galvanic isolation between the ETPL function and rest of the circuits

•Connection to any point of the monitored ETPL bus

•Minimal loading of the ETPL line

•Logic analyzer connection, with a provided cable pin-to-pin compatible with the Saleae Logic 8 and Logic Pro

8/16 analyzer series

•Powered through a USB connector by a 5.0 V source, typically a USB power bank, or a USB cable connected

to a computer

•Integrated keep-alive function to avoid power bank self shut-off

User manual Rev. 2 — 23 June 2023

5 / 15

NXP Semiconductors UM11650

KIT-TPLSNIFEVB tool

4.2 Block diagram

aaa-042712

TPL

MC33664

The TPL sniffer interfaces the TPL bus

with transformer isolation

TPL frames are received and sent in SPI

format by the MC33664 and buffered by the

cable driver

Internal power supplies generate the required 3.3 V and 5 V

and implement a pulsed load to provide the power bank

keep-alive function

TPL_IN

TPL_OUT

CABLE

DRIVER

CHARGE

PUMP LDO

Galvanic isolation

MICRO-USBCONN

4x2

PULSED

LOAD

5 V

3.3 V

2x1CONN 2

Figure 4. TPL sniffer block diagram

4.3 Schematics

The schematics for the KIT-TPLSNIFEVB tool are available at http://www.nxp.com/KIT-TPLSNIFEVB.

5 Configuring the hardware

The TPL sniffer exposes a set of connectors on two sides. One side is dedicated to the ETPL bus connection

and on the other side all other connectors are present. The two sides are galvanically isolated from each other:

the ETPL bus connectors are isolated from all other accessible points on the housing.

5.1 Connecting to the ETPL bus

As shown in Figure 4, the ETPL connectors are on one side of the housing and are marked TPL_IN and

TPL_OUT with a polarity indication + and −. The correct polarity of the connection is mandatory for the proper

functioning of the sniffer and, in most cases, also for the system to be sniffed.

Conversely, the terms IN and OUT are conventional and the two connectors are electrically in parallel inside

the TPL sniffer. They are physically duplicated to make it easier to connect the wires in certain use cases. If

there is a daisy chain, the original ETPL bus is cut and the two ends must be plugged onto the receptacles of

the TPL sniffer shown in Figure 5. In other cases, for example, when the ETPL bus has only one differential

end available for connection to the TPL sniffer, there is no difference between the TPL_IN and TPL_OUT

connectors, as long as the polarity is respected.

As a rule, if a stub is created from the original ETPL bus, its length should be as short as possible.

User manual Rev. 2 — 23 June 2023

6 / 15

NXP Semiconductors UM11650

KIT-TPLSNIFEVB tool

Note: The two ETPL interface connectors are named J1 and J2 in the schematic diagram.

Figure 5. ETPL bus connectors

5.1.1 Optional ETPL bus loading

The TPL sniffer is designed to add minimal load to the ETPL bus by default. Therefore, it does not add any

termination impedance and the differential load seen from the bus is that of an input impedance of the MC33664

reflected on the high-voltage side by the 1 : 1 ratio T1 isolation transformer.

If an interface other than the default one is desired, some settings are possible on the printed-circuit board

(PCB):

•The two jumpers JP1 and JP2 on the bottom side, should be closed (with a drop of solder) if a standard 150 Ω

termination is desired.

•Additional component footprints are available on the top side of the PCB to accommodate different loads on

the ETPL bus interface. These footprints are R13 [default do not populate (DNP)] and R14 and R15 (default

0 Ω).

Note: If the board must be modified and then powered without housing, proceed with caution.

5.2 Power and data connections

The side of the case opposite the ETPL connectors has all the other available connectors of the TPL sniffer.

•The GND banana plug: used to connect, if necessary, the GND of the TPL sniffer to another potential. It is

labeled J5 in the schematics.

In some cases of use, the whole system including, for example, the TPL sniffer, the power supply, the logic

analyzer, and the associated PC, could be an electrically floating block. This connector allows the ground

potential of the system (the TPL sniffer and anything else that has its ground connected to the TPL sniffer

ground) to be set to any other convenient potential: the protective earth or the vehicle chassis ground (KL31).

•The data-out 8-pin connector: buffered SPI signals to be routed to the logic analyzer. It is labeled J3 in the

schematics. See Section 5.2.1 "Connecting to the logic analyzer" for more details.

•The power on LED indicator

•The USB Micro-B connector: to connect to a 5.0 V source. It is labeled J4 in the schematics.

User manual Rev. 2 — 23 June 2023

7 / 15

NXP Semiconductors UM11650

KIT-TPLSNIFEVB tool

Figure 6. Power and data connectors

5.2.1 Connecting to the logic analyzer

The data output connector (J3) is an 8-pin 4 × 2 male connector used as an interface to the logic analyzer, to

transfer TPL messages converted to SPI format.

The signals are all unidirectional and their direction is from the TPL sniffer (output) to the logic analyzer (input).

The TPL sniffer is designed such that the cable connection to the logic analyzer can be relatively long, with a

maximum length of 2 m. The connection is also designed to be without loss of signal integrity and therefore

maintaining the logic and timing information.

This statement is only true if the following two rules are both satisfied:

•The cable used for the connection must have a characteristic impedance of 100 Ω. This impedance is the

impedance normally found on standard IDC ribbon cables.

•The logic analyzer side of the cable should only be loaded with high-impedance terminations. These

terminations can be a high-Z input from an oscilloscope, for example, 15 pF || 1 MΩ, or 5 pF || 10 MΩ (better),

or digital inputs from a logic analyzer (for example, 10 pF || 2 MΩ).

Failure to follow these rules does not guarantee proper operation of the TPL sniffer, unless the cable length is

considerably short (< 15 cm). In this case, reflections in the cable can be neglected.

For signal integrity and electromagnetic interference (EMI) reduction, the data lines are interleaved with the

ground potential with the pinout described in Table 1.

The TPL sniffer data output lines and the ETPL inputs are internally protected by electrostatic discharge (ESD)

suppression devices. Nevertheless, standard electrostatic precautions should be taken when handling and

using the TPL sniffer.

The pin assignment for the data output connector is described in Table 1.

User manual Rev. 2 — 23 June 2023

8 / 15

NXP Semiconductors UM11650

KIT-TPLSNIFEVB tool

Pin Signal Description

1 INTB SPI interrupt signal

2 GND ground

3 RXCLK SPI bus clock

4 GND ground

5 RXDATA SPI bus data

6 GND ground

7 RXCSB SPI chip select

8 GND ground

Table 1. Analyzer connector (J3) pin assignment

Figure 7. Analyzer connector pinout

The supplied 8-pin connection cable should be plugged into the ANALYZER connector with the blue wires on

top (NXP logo side) and the black wires on the bottom.

5.2.1.1 Interfacing with the Saleae logic analyzer

The supplied 8-pin connectors cable is fitting the Saleae Logic 8 and Logic Pro 8/16 analyzer series input

connectors. To connect to the Saleae logic analyzer, the cable should be plugged with the blue wires on top

(Saleae logo side) and the black wires on the bottom.

User manual Rev. 2 — 23 June 2023

9 / 15

NXP Semiconductors UM11650

KIT-TPLSNIFEVB tool

Figure 8. Saleae logic analyzer

Saleae provides a software interface with its product to help decode the acquired signals. To learn more, visit

the Saleae website.

Plug-ins and extensions for the Saleae logic analyzer software are available to decode TPL frames. Visit http://

www.nxp.com/KIT-TPLSNIFEVB for more details.

5.2.2 Powering the TPL sniffer

The TPL sniffer can be powered through the USB Micro-B connector (J4, labeled PWR) by a 5.0 V source with

50 mA (average) and 150 mA (peak). This power supply can typically be a USB power bank, or a USB cable

connected to a computer.

5.2.2.1 Power bank keep-alive function

The purpose of the keep-alive feature is to avoid the activation of the automatic shutdown feature found on most

consumer USB power banks. Such a shutdown would likely occur due to the limited power consumption of the

TPL sniffer circuit alone, in the 10 mA to 20 mA range. Therefore, the sniffer activates an additional 150 mA of

internal power consumption with a period of 5.8 seconds and a duty cycle of 20 % (all figures are approximate).

This behavior simulates a load large enough to keep most power banks energized.

If the power-on LED indicator goes out shortly after the TPL sniffer is first powered up with a power bank,

consider trying another power bank model.

6 Hardware specifications

Description Value

Power supply voltage 5.0 V (± 10 %)

Power consumption < 50 mA (averaged over 20 seconds)

Table 2. Electrical characteristics

User manual Rev. 2 — 23 June 2023

10 / 15

Inhaltsverzeichnis

Andere NXP Semiconductors Computerhardware Handbücher

NXP Semiconductors

NXP Semiconductors HVP-56F80748-UM Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MCIMX7SABRE Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors NavQPlus Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors UM11768 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors i.MX 8M Plus Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors IMXRT500HDG Leitfaden

NXP Semiconductors

NXP Semiconductors WCT1012 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors i.MX 8M Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors RD9Z1-638BJBEVM Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors freescale MC9S12G128 MCU Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors UM10569 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors Android i.MX 8M Mini Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MCXN 4 Series Leitfaden

NXP Semiconductors

NXP Semiconductors UM10694 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors AN11211 Fehlerbehebungshandbuch

NXP Semiconductors

NXP Semiconductors LPC288 Series Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors UM11596 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors Freescale TWR-S12G240 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors QorIQ LS1028A Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors OM13488 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors freescale MCF5225X Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors UM11620 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors UM10301 PCA2125 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors i.MX 6Dual Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung