NXP Semiconductors OM15008 Bedienungsanleitung

UM10911

OM15008 smart lighting module

Rev. 1.1 —29 April 2016

User manual

Document information

Info

Content

Keywords

JN5169, remote control, lighting, SSL, LED, PCB antenna, ZigBee, NFC

Abstract

This user manual provides basic information about the OM15008

reference design. The OM15008 board contains a RF remote control for

lighting applications. The board must be supplied with a low DC voltage

of typical 2.5 V.

The JN5169 has 512 kB internal flash memory so no external flash

memory is needed.

NXP Semiconductors

UM10911

OM15008 smart lighting module

UM10911

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 1.1 —29 April 2016

2 of 19

Contact information

For more information, please visit: http://www.nxp.com

Revision history

Rev

Date

Description

0.0

20150624

Initial version

0.1

20150624

Change NT3H1201 with NT3H1101, connect NFC Field Detect signal to JN5169

1.0

20151117

First released

1.1

20160419

Add the JN-AN-1221 reference for binary file

1.2

20160429

Add the new Production Flash Programmer JN-SW-4107

NXP Semiconductors

UM10911

OM15008 smart lighting module

UM10911

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 1.1 —29 April 2016

3 of 19

1. Safety warning

Warning

Lethal voltage and fire hazard

The non-insulated high voltages that are present when operating this product constitute a risk

of electric shock, personal injury, death and/or ignition of fire.

This product is intended for evaluation purposes only. It shall be operated in a designated test

area by personnel qualified according to local requirements and labor laws to work with

non-insulated mains voltages and high-voltage circuits. This product shall never be operated

unattended.

The board must be connected to (rectified) mains voltage. Avoid touching the demo

board while it is connected to the mains voltage. An isolated housing is obligatory when

used in uncontrolled, non-laboratory environments. Galvanic isolation, of the mains

phase using a variable transformer is always recommended.

a. Isolated

b. Non isolated

Fig 1. Variable transformer isolation symbols

2. Introduction

The OM15008 smart lighting module is a highly versatile board that can be used in all

kinds of applications but focuses on lighting applications. Because the board is so

versatile, several components might left out in a specific application. The board is split up

in two parts:

RF part containing JN5169

RF antenna

The board can be placed on top of a Large Signal Board (LSB) that containing a LED

driver in order to create a fully functional remote controllable lamp.

The JN5169 is an ultra-low power, high performance wireless microcontroller suitable for

ZigBee applications, remote control and Active RFID.

The PCB antenna can also be removed in order to connect an external antenna via a

coaxial wire.

If the JN5169 with 512 kB memory is mounted on this board, then the antenna matching

components need to be modified. More on this can be found in sections 6 and 7 of this

manual.

NXP Semiconductors

UM10911

OM15008 smart lighting module

UM10911

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 1.1 —29 April 2016

4 of 19

3. Specification

DC supply voltage of typically 2.5 V

Integrated PCB antenna

Minimum of external components needed

Low standby power

4 digital outputs

1 digital input

1 analog input or digital input

Table 1. OM15008 module specification

Parameter

Comment

Min.

Typ.

Max.

Units

DC supply voltage

2.5

3.6

power consumption

measured at 2.5 V supply voltage

ambient temperature

25

+125

°C

4. Board connections

Fig 2. Board connections

NXP Semiconductors

UM10911

OM15008 smart lighting module

UM10911

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 1.1 —29 April 2016

5 of 19

5. Programming the board

The OM15008 board can be programmed using the Atomic USB programming dongle +

OM15037 adapter board and a standard USB cable. The Atomic programming dongle

can be ordered from www.atomicprogramming.com. Contact your local NXP support

office for the OM15037 adapter board.

A flex foil is used to connect the OM15008 board to the OM15037 board. Suitable flex

foils can be found in Table 2.

Table 2. Flex foils

Manufacturer

Manufacturer code

Supplier

Supplier code

Molex

98267-0233

Farnell

1079968

WURTH ELEKTRONIK

686608200001

Farnell

1908567

Note: the flex foil must be twisted when connecting the two boards. Twisted means that

on board the metal contacts of the flex foil are facing up and on the other board the

contacts are facing towards the board as is depicted in Fig 3.

Fig 3. Programming cable connections

The Atomic programming board supplies the OM15008 board with 3.3 V during the

programming. The programming board contains a voltage regulator that derives 3.3 V

from the 5 V that is supplied from the USB port.

Driver of USB serial interface and programming software can be found in the Production

Flash Programmer JN-SW-4107, full details provided in Production Flash Programmer

User Guide JN-UG-3099.

Do not supply the OM15008 board via an external supply during programming.

The programming method described here is suitable for use in prototypes. However, for

mass production, either program the flash before assembly or after assembly use

programming pads on the PCB and needles rather than a programming connector.

Refer to JN-AN-1221 for the binary file generation.

NXP Semiconductors

UM10911

OM15008 smart lighting module

UM10911

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 1.1 —29 April 2016

6 of 19

6. Schematic

The OM15008 board can also be fitted with a JN5169 which has 512 kB embedded flash,

lower standby power and 10 dBm transmit power. The antenna matching circuit and

crystal oscillator component value's must be changed when the JN5169 is mounted.

(1) DIO17/SPISMISO/SIF_D/COMP1M/PWM4.

(2) DIO16/SPISMOSI/SIF_CLK/COMP1P.

(3) DIO1/ADE/SPISEL2/ADC4/PC0.

(4) DIO0/ADO/SPISEL1/ADC3.

(5) DIO19/SPISEL0.

(6) DIO18/SPIMOSI.

(7) DO1/SPIMISO/PWM3.

(8) DO0/SPICLK/PWM2.

Fig 4. JN5169 design with minimum required external components

NXP Semiconductors

UM10911

OM15008 smart lighting module

UM10911

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 1.1 —29 April 2016

7 of 19

7. Bill of Material application

Table 3. Bill of material

Absolutely required

Reference

Description and values

Part number

Manufacturer

Yes

1.8 pF

GRM1555C1H1R8CA01D

MURATA

Yes

1 pF

GRM1555C1H1R0CA01D

MURATA

Yes

C31

12 pF

GRM1555C1H120JA01

MURATA

Yes

C32

12 pF

GRM1555C1H120JA01

MURATA

Yes

C34

100 nF

GRM155R71C104KA88D

MURATA

Yes

C36

100 nF

GRM155R71C104KA88D

MURATA

Yes

C38

10 nF

GRM155R71H103KA88D

MURATA

Yes

C39

100 nF

GRM155R71C104KA88D

MURATA

Yes

C40

47 pF

GRM1555C1H470JA01

MURATA

Yes

C42

100 nF

GRM155R71C104KA88D

MURATA

Yes

C43

100 nF

GRM155R71C104KA88D

MURATA

Yes

C49

2.2 F

GRM188R71A225KE15D

MURATA

Yes

4.3 nH

LQG15HN4N3S02

MURATA

Yes

3.0 nH

LQG15HN3N0S02

MURATA

Yes

R15

43 k

RC0402FR-0743KL

YAGEO

Yes

1 k

RC0402FR-071KL

YAGEO

Yes

JN5169

NXP

Yes

32 MHz Xtal

X32M000000S039A

AEL

NXP Semiconductors

UM10911

OM15008 smart lighting module

UM10911

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 1.1 —29 April 2016

8 of 19

8. Board layout

Fig 5. Top and bottom OM15008 layout

Note: the top side of the OM15008 board is facing towards the top side of the Large

Signal Board (LSB).

NXP Semiconductors

UM10911

OM15008 smart lighting module

UM10911

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 1.1 —29 April 2016

9 of 19

9. Board dimensions

Fig 6. Board dimensions

10. Functional description

10.1 Pinout

The OM15008 board has a programming connector and two headers:

Table 4. Pin list for the programming connector

Pin name

JN5169 pin

Function

Electrical

J3.1

DIO5

27 (DIO5)

0 V to 3.6 V

J3.2

DIO4

26 (DIO4)

0 V to 3.6 V

J3.3

SPIMISO

22 (SPIMISO)

0 V to 3.6 V

J3.4

DIO7

29 (DIO7)

digital I/O (UART)

0 V to 3.6 V

J3.5

DIO6

28 (DIO6)

digital I/O (UART)

0 V to 3.6 V

J3.6

RESETN

3 (RESET_N)

digital I/O (Reset_not signal for microcontroller)

0 V to 3.6 V

J3.7

GND

ground

0 V

J3.8

VCCRF

9/30 (VDDA/VDDD)

supply

0 V to 3.6 V

NXP Semiconductors

UM10911

OM15008 smart lighting module

UM10911

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 1.1 —29 April 2016

10 of 19

Table 5. Pin list for header J2

Pin name

JN5169 pin

Function

Electrical

J2.1

RESETN

3 (RESET_N)

0 V to 3.6 V

J2.2

DIMMER_BLEED

17 (DIO1)

bleeder output when the board is used in dimmer

tolerant solutions

0 V to 3.6 V

J2.3

VAUX_MON

32 (DIO9)

VAUX monitor input when the board is applied in low

cost solutions

0 V to 3.6 V

J2.4

PWM1

33 (DIO10)

PWM1 output (Brightness control)

0 V to 3.6 V

J2.5

PWM2

34 (DIO11)

PWM2 output (CCT control when the board is used in

tunable white solution)

0 V to 3.6 V

J2.6

37 (DIO13)

ON/OFF output

0 V to 3.6 V

Table 6. Pin list for header J6

Pin name

JN5169 pin

Function

Electrical

J6.1

ADCIN

15 (ADC1)

1 (DIO16)

input for AD converter

input for comparator

0 V to 3.6 V

J6.2

GND

0 V

J6.3

VCCRF

9/30 (VDDA/VDDD)

0 V to 3.6 V

The RESET_N pin of the JN5169 is connected to J3.6 and J2.1 and susceptible for

noise. So do not connect a programming cable or long wires to these pins. The

RESET_N pin is connected to VCCRF via a pull up resistor. The minimum value of this

resistor depends on the programming board that is used: if for example the Atomic

programming board is used, then the minimum value of the pull-up resistor depends on

the maximum current that the FTDI chip on the Atomic programming board can sink.

Header J2 has 4 digital outputs to the LSB that can be used to control the LED driver on

the LSB. The function of these pins depends on the LSB on which the OM15008 board is

mounted and the software that is used.

The VAUX_MON input can be used for standby voltage control in combination with

specific large signal boards.

There are RC-filters on the PWM outputs as the board is operating in a noisy

environment. In this way is prevented that noise is injected from the LSB into the DIO's

which might cause problems. The filters are placed as close as possible to the DIO pins

of the JN5169. Ideally the 470 pF capacitors should have been placed directly between

the DIO-pins and ground, but because the PWM output is switching this would result in

switching spikes through the capacitors. For that reason the filter capacitors are placed

between the pin's of J2 and ground and then they are connected to the DIO pins via a 2.2

kresistor.

Header J6 is used for supplying the board and J6.2 is an input that can be routed to 2

different pins: ADC1 and DIO16. The first input is an ADC and it can be used to monitor

e.g. the bus voltage. The second input is a comparator and this input can be used for

synchronizing the PWM frequency with the mains frequency.

Inhaltsverzeichnis

Andere NXP Semiconductors Steuereinheit Handbücher

NXP Semiconductors

NXP Semiconductors TWR-K64F120M Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MC56F8013 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors TWR-56F8400 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors A3M38SL039 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors freescale TWR-TWRPI-BD Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors Freescale TWR-WIFI-GS1500M Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors LPC55S6 Series Montage- und Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors OM27642 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors Freescale MC9S12C32 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors freescale TWR-S08PT60 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors LPC54018 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors TWR-MCF5441X Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors TWR-LS1021A Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors freescale TWR-MCF51JG Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors TWR-SER2 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors TWR-KL43Z Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PN544 C2 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PX series Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors QN9090 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors Digital DNA MSC8102 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors TDA8920 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors i.MX8 QM Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors M68EM05F4 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PMSMFRDMMCXN947 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung