Oakton PC 700 Bedienungsanleitung

Instruction Manual

PC 700 pH/mV/Conductivity/ºC/ºF

Bench Meter

Technolo

ade

Part of Thermo Fisher Scientific 68X541704 Rev. 1 Feb. 2010

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

TABLE OF CONTENTS

1. INTRODUCTION.............................................................. 1

2. GETTING STARTED........................................................ 2

2.1 Keypad Functions ................................................................... 2

2.2 LCD Annunciators ................................................................... 3

2.3 Meter Connections .................................................................. 3

3. CONDUCTIVITY ELECTRODE ....................................... 4

4. PH AND MV CALIBRATION............................................ 4

4.1 pH Calibration ......................................................................... 4

4.2 Millivolt (mV) Offset Adjustment .............................................. 6

5. CONDUCTIVITY AND TDS CALIBRATION.................... 6

5.1 Automatic or Manual Calibration ............................................. 6

5.2 Single or Multi-Point Calibration .............................................. 7

5.3 General Calibration Tips ......................................................... 8

5.4 Automatic Conductivity Calibration Procedure ........................ 8

5.5 Manual Conductivity & TDS Calibration Procedure................. 9

5.6 Temperature Calibration ......................................................... 9

6. CONDUCTIVITY AND TDS MEASUREMENT ................ 10

6.1 Taking Measurements............................................................. 10

6.2 Automatic and Manual Ranging .............................................. 10

7. HOLD FUNCTION............................................................ 11

8. STORING AND RECALLING DATA ............................... 11

9. SETUP FUNCTIONS........................................................ 12

9.1 1.0 CAL (Calibration)...............................................................12

9.2 2.0 ELE (Electrode Information) .............................................. 12

9.3 3.0 ConF (Configuration).........................................................13

9.4 3.1 rdY (Ready / Stability Indicator)......................................... 13

9.5 3.2 ºC ºF (Celsius or Fahrenheit) ............................................ 13

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

9.6 3.3 buFF (pH Buffers & Calibration Points)—pH only .............13

9.7 3.3 AtC (Auto Temp Compensation)—Con & TDS only.......... 13

9.8 3.4 tdS (TDS factor)—Con & TDS only ................................... 14

9.9 3.5 t.CO (Temperature Coefficient)—Con & TDS only............ 14

9.10 3.6 t.nr (Normalization Temperature in ºC)—Con & TDS only 14

9.11 3.7 ACAL (Auto Conductivity Calibration)—Con & TDS only .. 15

9.12 3.8 SPC (Single Point Calibration)—Con & TDS only ............. 15

9.13 3.8 CELL (Nominal Cell Constant)—Con & TDS only............. 15

9.14 4.0 rSt (Reset)......................................................................... 16

9.15 5.0 CLr (Clear Memory) .......................................................... 16

10. CALCULATING TDS CONVERSION FACTOR.............. 17

11. CALCULATING TEMPERATURE COEFFICIENTS........ 18

12. REPLACEMENTS AND ACCESSORIES........................ 19

13. TROUBLESHOOTING GUIDE......................................... 20

14. SPECIFICATIONS............................................................ 22

15. WARRANTY..................................................................... 24

16. RETURN OF ITEMS......................................................... 25

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

1. INTRODUCTION

Thank you for purchasing our PC 700 series benchtop meter.

This microprocessor-based meter is economical and simple to

use. The design incorporates a large LCD for clear viewing, yet

offers a small footprint to conserve space.

The PC 700 measures pH, mV (ORP), conductivity, or TDS

simultaneously with temperature (ºC or ºF).

Each meter includes a convenient slide-out card for quick

reference. Also included is an electrode arm and metal bracket

which can be easily attached to the left or right side of the meter

according to your preference.

The PC 700 benchtop meter replaces our popular pH/CON 510

series meter that was introduced in 2000.

We take great pride in every instrument we manufacture

and hope this one serves you well.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

2. GETTING STARTED

2.1 Keypad Functions

Powers the meter on and off. Upon power on, the meter

automatically begins in the mode that was last used.

Calibration and memory values are retained even if meter

is unplugged.

Toggle between available measurement modes—

pH/Temp, mV/Temp, Conductivity/Temp, or TDS/Temp.

Also used to switch to Temperature calibration during pH,

mV, Conductivity or TDS calibration modes.

Press and hold for 5 seconds to enter SETUP mode.

Toggles between measurement and calibration modes.

In SETUP mode, returns user to the measurement mode.

Confirms calibration values in CAL mode.

Confirms selections in SETUP mode.

Changes Con/TDS range and resolution in MEAS mode.

View recalled values in memory mode.

MI (Memory Insert) stores values into memory.

Increase value. Scroll up in SETUP & CAL modes.

MR (Memory Recall) recalls values from memory

Decrease value. Scroll down in SETUP & CAL modes.

Freezes measured reading. Press again to resume

live reading.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

2.2 LCD Annunciators

2.3 Meter Connections

DC Power supply

CON/

TEMP 8-pin DIN connection for 2-cell Con/TDS/Temp electrode

pH BNC connection for pH, or ORP (Redox) electrode

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

3. CONDUCTIVITY ELECTRODE

The PC 700 includes an electrode with a nominal cell constant of k

= 1.0, built-in temperature sensor, and 1 meter cable. The Ultem

body housing has good chemical resistant properties. The

electrode design offers fast temperature response and reduces air

entrapment, ensuring accurate, repeatable, and stable readings.

The wetted materials of the probe include:

Polyetherimide (Ultem) – protective probe guard

Polybutylterphalate (Valox) – sensor housing

Stainless Steel (SS 304) – 2 bands

The protective probe guard can be removed temporarily for

cleaning however it must be re-attached during measurement and

calibration. Erroneous results will occur while the probe guard

is removed.

Always immerse the probe beyond upper steel band for best

results. Use the fill line on the outside of the probe guard for

reference.

4. PH AND MV CALIBRATION

4.1 pH Calibration

For best results, periodic calibration with known accurate standards

recommended. Calibrate with standards that bracket your intended

measuring range while including a neutral standard (pH 7.00 or 6.86).

For example, if you expect to measure samples from

The PC 700 meter can be calibrated with up to 5 buffers. The

non-vola

pH 6.2 to pH 9.5,

alibration with 4.01, 7.00, and 10.01 will work well.

tile memory retains all calibration values upon meter shut

wing calibration standards are automatically recognized;

down.

The follo

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

e buffer groupSee Section 9.6 to change th

1) Press as needed to select pH.

Dip the pH and ATC electrodes into pH buffer and press2) . The

secondary display will lock on the appropriate buffer value. Provide

ing for best results. When the READY indicator appears, prstirr ess

to accept. The primary reading will flash briefly before the

secondary display begins scrolling the remaining available buffers.

Rinse the pH and ATC electrodes then dip into the next pH buffe

The secondary display will lock on the appro ate buffer value.

When the READY indicator appears, press

3) r.

pri

to accept. The

primary reading will flash briefly then display the percent efficiency

(slope) before the secondary display begins scrolling the remaining

available buffers.

To calibrate another buffer repeat step 3) or press to return to

the measurement mode. Note: The meter will automatically return

to measurement mode upon successful completion of the numbe

specified calibration points. To spec

r of

ify a different number of pH

int (offset) calibration is only allowed with pH 7.00 or

pted during a new calibration,

calibration points see Section 9.6.

IPS: A single poT

pH 6.86 buffers.

When the first calibration value is acce

all prior libration values are erased.

ressP at any time to abort calibration and return to measurement

USA buffer group 1.68, 4.01, 7.00, 10.01, 12.45

NI 5ST buffer group 1.68, 4.01, 6.86, 9.18, 12.4

mode.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

tandard in which a meter/electrode system are

are

match the ORP value.

4.2 Millivolt (mV) Offset Adjustment

Oxidization Reduction Potential (ORP or Redox) is not a precise

measurement, but is useful as a relative indicator. As such, mV offset

adjustment is not meant to enhance accuracy, but rather to make

readings comparable to a reference. Commercial ORP solutions are

often used as a check s

verified to be close to a given value, instea of being used as a

calibration standard in which adjustments made in an attempt to

1) Connect an ORP electrode and press as needed to select

(or R.mV).

2) Dip the ORP electrode into a solution with a known mV value

(i.e. Zobel, Light’s, quinhydrone, or iodidetriiodide) and stir.

3) Press when the reading is stable he prima display shows

the relative millivolt value (R.m ) whi he secon ry display sho

factory default mV value.

Adjust the R.mV value using

. T ry

V le t da ws

the

) or . Press4to accept or

to cancel. The meter allows an adjustable maximum value of

150

mV from the factory default mV value.

mV.

Note: When an offset has been stored successfully, R.mV replac

5. CONDUCTIVITY AND TDS CALIBRATION

5.1 Automatic or Manual Calibration

The PC 700 is capable of automatic or manual calibration for

conductivity, and manual calibration for TDS.

In the automatic calibration mode, the meter will automatically se

one of (4) conductivity calibration standard values depending on the

range and normalization temperature being used (TABLE 1).

lect

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

isted in TABLE 1, the PC 700 must

be set for manual calibration i

The factory default is automati

an ere i

for e 1.

TABLE

If you only use calibration standards that are listed in TABLE 1,

automatic calibration is recommended. If you intend to calibrate with

one or more standards that are not l

nstead.

c conductivity calibration. See Section

s no automatic calibration value9.11 to ch

available

ge this setting. Th

conductivity rang

Auto Calibratio esmatic n Valu

N ation Tempormaliz erature

R eang

# Conductivity

Range 25 ºC 20 ºC

r 1 0.00 – 20.00 μS None None

r 2 20.1 – 200.0 μS 84 μS 76 μS

r 3 201 – 2000 μS 1413 μS 1278 μS

r 4 2.01 – 20.00 mS 12.88 mS 11.67 mS

r 5 20. 111.8 mS1 – 200.0 mS 102.1 mS

Range

# TDS Range

(us r)ing 0.5 TDS facto Automatic Calibration

Values

r 1 0 – 10.00 ppm none

r 2 10.1 – 100.0 ppm none

r 3 101 – 1000 ppm none

r 4 1.01 – 10.00 ppt none

r 5 10.1 – 100 ppt none

5.2 Single or Multi-Point Calibration

Use Single-Point Calibration to apply a single calibration value across

all ranges.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Inhaltsverzeichnis

Andere Oakton Messgerät Handbücher

Oakton

Oakton 450 Series Bedienungsanleitung

Oakton

Oakton pHTutor Bedienungsanleitung

Oakton

Oakton PC 300 Bedienungsanleitung

Oakton

Oakton 35631-00 Bedienungsanleitung

Oakton

Oakton pH 5+ Bedienungsanleitung

Oakton

Oakton WD-35606-00, WD-35606-05 Bedienungsanleitung

Oakton

Oakton Ion 510 Series Bedienungsanleitung

Oakton

Oakton WD-35610-00 Bedienungsanleitung

Oakton

Oakton pH 300 Bedienungsanleitung

Oakton

Oakton CON 700 Bedienungsanleitung

Oakton

Oakton ION 6 Bedienungsanleitung

Oakton

Oakton 700 Series Bedienungsanleitung

Oakton

Oakton Acorn TEMP 4 Bedienungsanleitung

Oakton

Oakton ION 5 Acorn Series Bedienungsanleitung

Oakton

Oakton CON 10 Bedienungsanleitung

Oakton

Oakton Salt 6 Bedienungsanleitung

Oakton

Oakton pH 610 Bedienungsanleitung

Oakton

Oakton T100WL Bedienungsanleitung

Oakton

Oakton 35630-00 Bedienungsanleitung

Oakton

Oakton EC250 Bedienungsanleitung

Oakton

Oakton pH 5+ Bedienungsanleitung

Oakton

Oakton T-100IR Bedienungsanleitung

Oakton

Oakton CON550 Bedienungsanleitung

Oakton

Oakton WD-35427-10 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung