Oase Filtral UVC 700 Bedienungsanleitung

Filtral UVC 700 / 1200

Operating instructions

Notice d’emploi

Instrucciones de uso

- English -

REMINDER

CALL 1-866-627-3435

BEFORE RETURNING TO STORE.

Information about these operating instructions

Welcome to OASE Living Water. You made a great choice with the purchase of this product Filtral UVC 700/1200. Prior

to operating the unit, please read the instructions of use carefully and fully familiarise yourself with the unit. Ensure that

all work on and with this unit is only carried out in accordance with these instructions. Please strictly follow the enclosed

instructions to ensure safe and correct handling of the product. Keep these instructions in a safe place. Please also hand

over the instructions when passing the unit on to a new owner.

WARNINGS AND CAUTIONS SYMBOLS

Symbols used in these instructions

The symbols used in this operating manual have the following meanings:

Risk of injury to persons due to dangerous electrical voltage.

This symbol indicates an imminent danger, which can lead to death or severe injuries if the appropriate measures are

not taken.

Risk of personal injury caused by a general source of danger.

This symbol indicates an imminent danger, which can lead to death or severe injuries if the appropriate measures are

not taken.

Important information for trouble-free operation.

Intended use

Filtral UVC 700/1200, referred to in the following as “unit”, may only be used as specied in the following:

• For cleaning garden ponds.

• For operation with clean water.

• Operation under observance of the technical data.

The UVC lamp installed in the unit is intended to kill algae and bacteria in the pond water. Even in small doses, its radi-

ation is harmful for eyes and skin. Never use the UVC lamp in a defective housing or outside the housing, or any other

purpose other than that intended.

The following restrictions apply to the unit:

• Do not use in swimming pools.

• Never use the unit to convey uids other than water.

• Never run the unit without water.

• Do not use for commercial or industrial purposes.

• Do not use in conjunction with chemicals, foodstuff, easily ammable or explosive substances.

Use other than that intended

This unit can be dangerous and cause harm if not used in accordance with these instructions. Any use not in accordance

with these instructions or modication(s) to the unit will void the limited warranty.

Questions, problems, missing parts?

Before returning to your retailer, call us at 1-866-627-3435, 8 a.m.-6 p.m., EST, Monday-Friday, or email

us at customercare@oase-livingwater.com. Or visit our website at www.oase-livingwater.com

- English -

Installation

If NOT using the nozzle set

1. Screw the branch valve (D) on the connection thread of the UVC

water housing (A) using the washer (B). Close the upper outlet using

the cover cap (C).

2. Connect tubing for water features to the lateral separately regulated

connection of the branch valve.

NOTE: Tubing is NOT INCLUDED.

● Connect the other end of the tubing to desired water feature or spitter.

Filtral UVC 700

Important:

●The unit can be used with the following:

○ With the nozzle set to create various fountain displays.

○ With the branch valve, allowing an additional water feature to be operated simultaneously with the fountain nozzle.

●It is recommened to place the unit horizontally on the ground ensuring its stable position.

●Do not lift the unit by its power cord.

● The unit’s lter foam, biomedia, UVC and pump are preinstalled in the lter housing.

For installation using the nozzle set

1. Assemble the connection element for the ball joint (A) into the branch

valve (B).

2. Slide the clamping screw (D) down the tube and screw on to the

connection element for the ball joint (A) to secure the tube.

3. Screw in the nozzle mounting (E). Select a nozzle insert to use (F).

The fountain height and shape depend on the nozzle insert used.

4. Screw the assembly on the connection thread of the UVC water

housing (G) using the washer (H).

5. If desired, connect tubing for additional water features to the lateral

separately regulated connection of the branch valve.

NOTE: Tubing is NOT INCLUDED.

● Connect the other end of the tubing to desired water feature or spitter.

- English -

Installation (cont.)

Filtral UVC 1200

Important:

●The unit can be used with the following:

○ With the nozzle set to create various fountain displays.

○ With the branch valve, allowing an additional water feature to be operated simultaneously with the fountain nozzle.

○ With an air pump to enrich the water with additional oxygen

●It is recommened to place the unit horizontally on the ground ensuring its stable position.

●Do not lift the unit by its power cord.

● The unit’s lter foam, biomedia, UVC and pump are preinstalled in the lter housing.

For connecting the air pump (optional)

●Air pump is not included.

●Follow the air pump’s instructions for product assembly.

● OASE recommends using the AquaOxy air pump.

1. Pull the clamps on both sides of the bottom strainer casing (A)

to the side and lift off the top strainer casing (B).

2. Remove the top foam lter (C).

3. Inside the housing, connect the aeration stone (D) with a

section of the hose (E) to the air connector (F)

● Place the aeration stone (D) between the gravel bags (G).

●Ensure that the hose is not kinked.

● Connect the aeration pump to the air connector (F) outside of

the housing. Read the aeration pump documentation.

4. Place the foam lter (C) in the bottom strainer casing (A).

● Attach the top strainer casing (B) and press it onto the bottom

strainer casing (A) until the clamps engage in the bottom

strainer casing.

● Important: Lead the connection cable (H) through the cable

opening in the bottom strainer casing (A) and route the cable

such that pinching is avoided.

GAquaOxy

Questions, problems, missing parts?

Before returning to your retailer, call us at 1-866-627-3435, 8 a.m.-6 p.m., EST, Monday-Friday, or email

us at customercare@oase-livingwater.com. Or visit our website at www.oase-livingwater.com

- English -

For installation using the nozzle set

1. Slide the clamping screw (D) down the nozzle tube (C) and screw on

to the branch valve (B) to secure the tube.

2. Screw in the nozzle mounting (E). Select a nozzle insert to use (F).

The fountain height and shape depend on the nozzle insert used.

3. Screw the assembly on the reduction element (A). Then screw on to

the connection thread of the UVC water housing (G) using the washer

(H).

4. If desired, screw the reduction element (I) and the stepped hose

adapter (J) on the lateral outlet of the branch valve (B).

● Connect tubing for additional water features to the lateral separately

regulated connection of the branch valve.

NOTE: Tubing is NOT INCLUDED.

● Connect the other end of the tubing to desired water feature or spitter.

1. Pull the nozzle tube to the desired length.

2. Loosen the clamping screw to manuver the

nozzle tube.

3. Vertically align the nozzle tube and fasten

the clamping screw hand tight.

4. Fully open the rotary regulator (A) for

the fountain.

● The secondary rotary regulator (B)

is used to control the fountain/water

feature connected to the lateral outlet

of the branch valve.

● The additional water recirculation via

the lateral outlet improves the ltering

effect, even if the feature or the water

course is not connected.

Filtral UVC 700 / 1200

Setting the fountain/water feature

● Install the unit in the pond in a horizontal position on rm, sludge-free ground and

ensure that it is completely covered with water.

Installation (cont.)

Filtral UVC 1200

- English -

Start-up (Filtral UVC 700 / 1200)

Attention! Dangerous electrical voltage.

Possible consequences: Death or serious injuries.

Protective measures:

• Electrical units and installations with a rated voltage of U > 12 V AC or U >30 V DC located in the water: Isolate the

units and installations (switch off and disconnect from the power supply) before reaching into the water.

• Isolate the unit before starting any work.

• Secure the unit to prevent unintentional switching on.

Grounding instructions

This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of

electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord

having an appliance-grounding conductor and a grounding plug. The plug must be plugged into an appropriate

outlet that is installed and grounded in accordance with all local codes and ordinances.

Warning

Improper connection of the appliance-grounding conductor can result in a risk of electric shock. Check with a

qualified electrician or service representative if you are in doubt whether the appliance is properly grounded. Do not

modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified

technician.

Attention! Sensitive electrical components.

Possible consequence: The unit will be destroyed.

Protective measure: Do not connect the unit to a dimmable power supply.

Maintenance and cleaning

Attention! Dangerous electrical voltage.

Possible consequences: Death or serious injuries.

Protective measures:

• Electrical units and installations with a rated voltage of U > 12 V AC or U >30 V DC located in the water: Isolate the

units and installations (switch off and disconnect from the power supply) before reaching into the water.

• Isolate the unit before starting any work.

• Secure the unit to prevent unintentional switching on.

CAUTION

The ultra-violet radiation of the UVC lamp can burn your eyes and skin.

• Never operate the UVC lamp outside its casing.

• Never operate the UVC lamp in a casing that is defective.

Danger: Ultraviolet radiation.

Do not expose eyes to lamp rays.

Disconnect power before servicing or replacing lamp.

Replace lamp only with lamp rated 7 watts (UVC 700) 9 watts (UVC 1200):

Warning: To reduce the risk of electric shock - Connect only to a circuit that is protected by a ground-fault circuit

interrupter (GFCI)

For indoor and outdoor household use

Switching on: Connect the unit to the mains.

The unit switches on immediately.

Switching off: Disconnect the unit from the mains.

● The indicator lamp (A) indicates the ON/OFF status of the UVC lamp.

Questions, problems, missing parts?

Before returning to your retailer, call us at 1-866-627-3435, 8 a.m.-6 p.m., EST, Monday-Friday, or email

us at customercare@oase-livingwater.com. Or visit our website at www.oase-livingwater.com

- English -

Maintenance and cleaning (cont.)

1. Unscrew the branch valve (A) and the

attachment elements.

2. Pull the clamps on both sides of the bottom

strainer casing (B) to the side and lift off the

top strainer casing (C).

3. Remove the foam lter (D) and the UVC

clarifying unit including pump (E), and the ne

foam lters (F), bio surface elements (G) and

the gravel bag (H).

● Clean the bottom strainer casing (B) and the

top strainer casing (C) with clear water using

a brush.

● Wash out foam lters (D, F), bio-surface

elements (G) and the gravel bag (H) under

running water.

● Do not use chemical cleaning agents as they

would kill the micro-organisms in the different

lter media. At the beginning, this entails a

reduced lter capacity.

Opening the lter housing and cleaning the different lters

Filtral UVC 700 2.

Filtral UVC 1200

1. Unscrew the branch valve (A) and the

attachment elements.

2. Pull the clamps on both sides of the

bottom strainer casing (B) to the side and

lift off the top strainer casing (C).

2. B

- English -

3. Remove the UVC clarifying unit including pump (D), foam

lters (E, F), bio surface elements (G) and gravel bags (H).

● If an air pump was installed: put the aeration stone (I) to the

side.

● Clean the bottom strainer casing (B) and the top strainer

casing (C) with clear water using a brush.

● Wash out foam lters (E, F), bio-surface elements (G) and the

gravel bag (H) under running water.

● Do not use chemical cleaning agents as they would kill the

micro-organisms in the different lter media. At the beginning,

this entails a reduced lter capacity.

Filtral UVC 1200 (cont.) 3. D

Cleaning the pump

Filtral UVC 700 / 1200

1. Unscrew the pump (A) from the UVC water

housing (B). Remove the pump and place the

UVC water housing to the side.

2. Unscrew the pump lid (C) by turning counter-

clockwise (bayonet closure) and remove rotor (D).

3. Clean all pump components using clean water

and a brush. After cleaning the pump, reassemble

the pump in the reverse order.

● If you intend on cleaning the UVC water housing

do not screw the pump back into the housing.

1. 2.

BA C

Opening and cleaning the UVC water housing

Filtral UVC 700 / 1200

For safety reasons, the UVC lamp can only be switched on when the unit

head has been correctly tted into the casing

NOTE

● The UVC water housing (A) is fastened to the unit head (B) by means

of a bayonet closure.

1. Press on the engagement lug (C) at the unit head (B), turn the UVC

water housing (A) counter-clockwise and carefully pull it off the unit

head (B).

2. Clean the UVC water housing (A) under running water. Check the

quartz glass for damage and clean its outer face with a moist cloth.

Questions, problems, missing parts?

Before returning to your retailer, call us at 1-866-627-3435, 8 a.m.-6 p.m., EST, Monday-Friday, or email

us at customercare@oase-livingwater.com. Or visit our website at www.oase-livingwater.com

- English -

Closing the UVC water housing

Filtral UVC 700 / 1200

For safety reasons, the UVC lamp can only be switched on when the unit

head has been correctly tted into the casing

NOTE

● Check the O ring (C) for damage.

1. Place the O ring (C) on the recess at the unit

head (A).

2. Carefully push the UVC water housing (B)

on the unit head (A) by applying medium

pressure.

● Simultaneously, slightly turn the UVC water

housing (B) to ensure that the tenons (D)

slide into the grooves (E) of the bayonet

closure.

3. Turn the UVC water housing (B) clockwise against the stop and allow to

engage. The engagement lug (F) will click back into the unit head (A).

NOTE

For an optimum lter performance, we recommend to replace the UVC lamp after approx. 8000 operating hours.

See section Replace UVC lamp before reassembling the unit.

Reassembling the unit

Filtral UVC 700

1. Attach the pump (B) to the UVC water

housing (A) using the union nut.

2. Insert ne foam lter (C) in the bottom

strainer casing (D).

● Place the bio surface elements (E) and

the gravel bag (F) in the bottom strainer

casing (D).

● Insert the UVC clarifying unit including

the pump (A,B).

● Insert the foam lter (G).

1. 2.

A,B

C G

- English -

3. Important: Guide the connection cable (I) through

the cable opening at the bottom strainer casing

(D) and clip with the cable kink protection (J) in

the bottom strainer casing.

● Attach the top strainer casing (H) and press

down onto the bottom strainer casing (D) until the

clamps engage in the bottom strainer casing.

A,B

Reassembling the unit

Filtral UVC 1200

1. Attach the pump (B) to the UVC water

housing (A) using the union nut.

2. Place the bio surface element (D) and

gravel bags (E) in the bottom strainer

casing (C).

● If an air pump was installed: Place the

aeration stone (F) between the gravel

bags (E). Ensure that the hose is not

kinked.

● Place the foam lters (G, H) in the

bottom strainer casing (C) as shown.

● Insert the UVC clarifying unit including

the pump (A,B).

3. Important: Lead the connection cable

through the cable opening (I) in the

bottom strainer casing and route the

cable such that pinching is avoided.

● Attach the top strainer casing (J) and

press down onto the bottom strainer

casing (C) until the clamps engage in

the bottom strainer casing.

3. J

Andere Handbücher für Filtral UVC 700

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Oase Wasserfiltersystem Handbücher

Oase

Oase FiltoSmart 100 Bedienungsanleitung

Oase

Oase Filtral 2500 UVC Bedienungsanleitung

Oase

Oase Eco Control Bedienungsanleitung

Oase

Oase BioPress 4000 Bedienungsanleitung

Oase

Oase Filtral 1500 Kurzanleitung

Oase

Oase FiltoSmart 60 Bedienungsanleitung

Oase

Oase Filtral 5000 UVC Bedienungsanleitung

Oase

Oase BioPress 4000 Bedienungsanleitung

Oase

Oase AquaMax Eco Expert 21000 Bedienungsanleitung

Oase

Oase FiltoMatic CWS 7000 Bedienungsanleitung

Oase

Oase BioSmart 30000 Bedienungsanleitung

Oase

Oase BioTec 32000 Bedienungsanleitung

Oase

Oase BioPress 4000 Bedienungsanleitung

Oase

Oase FiltoClear 20000 Bedienungsanleitung

Oase

Oase Filtoclear Bedienungsanleitung

Oase

Oase Bitron C Bedienungsanleitung

Oase

Oase BioMaster 250 Bedienungsanleitung

Oase

Oase BioSmart 5000 Bedienungsanleitung

Oase

Oase BioTec ScreenMatic 2 40000 Bedienungsanleitung

Oase

Oase BioSmart 7000 Bedienungsanleitung

Oase

Oase Bitron Eco 120W Bedienungsanleitung

Oase

Oase Filtoclear 3000 Bedienungsanleitung

Oase

Oase StreamMax Classic 2000 Bedienungsanleitung

Oase

Oase BioPlus Series Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung