OHAUS 83021082 Bedienungsanleitung

Explorer®Balance

Ethernet Interface Option Kit

Installation Instructions

Explorer®Balance Ethernet Option Interface Kit EN-1

1. INTRODUCTION

The Ethernet Interface Option Kit provides a standard Ethernet interface for

Ohaus Explorer Series Balances.

Please read this manual completely before installation and operation.

CAUTION:

READ ALL SAFETY WARNINGS BEFORE INSTALLING,

MAKING CONNECTIONS, OR SERVICING. FAILURE TO

COMPLY WITH THESE WARNINGS COULD RESULT IN

PERSONAL INJURY AND/OR PROPERTY DAMAGE. RETAIN

ALL INSTRUCTIONS FOR FUTURE REFERENCE.

1.1 Kit Contents

Option Board

with face plate,

and standard

female RJ-45

Ethernet

connection.

EN-2 Explorer®Balance Ethernet Option Interface Kit

2. INSTALLATION

2.1 Safety Precautions

For safe and dependable operation of this equipment, please comply with

all safety precautions mentioned in this manual.

Note: Disconnect the equipment from the mains power supply before

beginning installation.

CAUTION:

The electronics of the Option are very sensitive to electrostatic discharges. In

order to protect the components, necessary measures must be taken when the

Option is installed so as to provide protection against electrostatic discharges.

2.2 Installation procedure

Please note the following:

The interface is installed into the Display and is powered by the Base.

Follow the steps below. Refer to the Figures when performing these steps.

Make sure Balance is unplugged

(turned OFF)

Detach the Display:

press buttons on both sides to

disconnect. Then pull Display away

from base.

Explorer®Balance Ethernet Option Interface Kit EN-3

Open the Display:

press button (enlarged in photo),

then lift Display until it disengages.

Unplug Display Communication

Cable, if desired, for greater

freedom of movement.

To release the clip that secures the

Display Communication Cable:

press out on both sides, as shown,

then unplug the Display

Communication Cable.

EN-4 Explorer®Balance Ethernet Option Interface Kit

Remove the two screws holding the

Option faceplate using a screw-

driver. Remove this plate. Save the

screws, they will be used to install

the new RS232 interface board.

Note: Do not touch any items inside

the Display.

Install the new Ethernet interface

board into the Display. Take care to

seat the device properly in the slot.

Push interface board into the Display

securely to engage it.

Note: Be careful not to touch

electronic components. Only touch

edges of interface board.

Re-install the two screws.

Plug in the Display Cable

Plug in a standard Ethernet Cable

to the Device.

Close the Display.

Explorer®Balance Ethernet Option Interface Kit EN-5

Route the RS232 Cable out either:

1. Under the Base and out the

Back, as shown at left;

or…

2. Out the side of the Display,

through the groove near the

release button (either side),

as shown here.

Re-wind any unused cable:

First remove the Platform, Sub-

Platform or Wind Ring, and Wind

Shield (if present).

Then turn base over to rewind cable

around cable guides (if needed).

Turn base upright and re-assemble.

Reconnect power to Base

(power ON).

Use the Level Assist feature to re-

level the Balance prior to operation.

(See Instruction Manual, Section 2.4.)

EN-6 Explorer®Balance Ethernet Option Interface Kit

3. OPERATION

Using the Ethernet Port to connect to a Local Area Network

After successful installation of

the Ethernet Interface Option,

the Ethernet appears as an

option on the Communication

Menu.

Press Ethernet to see options

for Device Settings and Print

Settings.

Press Device Settings to…

…see the IP Address, Port,

Default Gateway and Subnet

Mask settings.

Explorer®Balance Ethernet Option Interface Kit EN-7

The Port setting cannot be

changed.

Press IP Address to change

the setting.

Press Default Gateway to

change the setting.

Press Subnet Mask to change

the setting.

EN-8 Explorer®Balance Ethernet Option Interface Kit

Now press Print Settings to

select from a menu of options.

For additional information on

the available print options, see

the Explorer Balances

Instruction Manual.

4. MAINTENANCE

4.1 SERVICE INFORMATION

For Service assistance in the United States, call toll-free 1-800-526-0659

between 8:00 AM and 5:00 PM Eastern Standard Time. An Ohaus Product

Service Specialist will be available to assist you. Outside the USA, please

visit our website, www.ohaus.com, to locate the Ohaus office nearest you.

5. TECHNICAL DATA

5.1 Specifications

Part Number

83021082

Interface Type

Female RJ-45 Ethernet connection

Inhaltsverzeichnis

Andere OHAUS Adapter Handbücher

OHAUS

OHAUS RS232 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung