OHAUS RS232 Bedienungsanleitung
RS232 Interface
INSTRUCTION MANUAL
Interfaz RS232
MANUAL DE INSTRUCCIONES
Interface RS232
MODE D’EMPLOI
RS232-Schnittstelle
BEDIENUNGSANLEITUNG
Interfaccia RS232
MANUALE D’ISTRUZIONI
RS232 㓺
㓺Ԭ
ֵ⭞䈪᱄Ҝ
RS232
ࣥࢱ࣮ࣇ࢙ࢫ
ྲྀᢅㄝ᭩
RS232
넭뫥뵍넩걙
ꩡ끞ꐺ
Интерфейс RS232
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
RS232 Interface EN-1
INTRODUCTION
This Interface Kit is for use with OHAUS Scout STX, SPX, SKX, SJX series and
PJX series products.
INTERFACE INSTALLATION
Install the Interface module on the mini DIN port (round connector) located at the
rear side of the balance as shown. During this process, please make sure the
balance is powered off.
Notes:
x Please make sure the small triangle mark (▲) on the round connector is at
the bottom and then plug in.
x The appearance of your model may be different.
SETUP
A) The OHAUS Interface is preset to communicate using the following settings:
9600 baud, 8 bit, no parity, no handshake. Determine the RS232 parameters
required for the printer or computer that is to be connected. See computer or
printer documentation if assistance is required. If the parameters do not match,
it will be necessary to change either the balance settings, or the computer /
printer settings.
B) Upon installation of the interface, the balance will recognize the RS232
Interface and add relevant items to the menu. Configure the balance to the
desired RS232 and printing parameters; refer to the balance Instruction Manual
for assistance in using the menus.
Mini DIN port
(Round connector)
EN-2 RS232 Interface
For SPX, SKX and SJX Balances:
Upon installation, the balance will show [r.S.2.3.2] during the power sequence.
PRINT
Reset: no, yes
Stable: off, on
A.Print: off
On.Stable
interval
accept
continuous
Content: Result (-> off, on)
Gross (-> off, on)
Net (-> off, on)
Tare (-> off, on)
Header (-> off, on)
Footer (-> off, on)
Mode (-> off, on)
Unit (-> off, on)
Info (-> off, on)
Layout: Format (->Single,Multi)
Feed (->Line, 4 Lines, Form)
End Print: Exit menu
RS232
Reset: no, yes
Baud Rate: 1200…9600…115200
Parity: 7 even, 7 odd, 7 none,
8 none
Stop bit: 1, 2
Handshake: none, XOn-XOff
Alternate command: Print (A…P…Z)
Tare (A…T…Z)
Zero (A…Z)
End RS232: Exit menu
Note: Items with bold font are default settings.
SETUP DEFINITIONS
Menu Settings
Explanation
PRINT / A. Print
– Off
Only sends data when PRINT is pr
essed.
PRINT / A.Print / On.Stable
– Load,
Load.Zero
Balance only transmits stable data.
Load
: Print stable value excluding zero
Load.Zero: Print stable value including zero
PRINT / A.Print / interval
- (xx) sec
Balance sends data every (xx) seconds.
PR
INT / Auto Print – accept
Balance only sends stable accept data in
Check mode.
PRINT / A.Print
– Continuous
Balance repeatedly sends data as fast as
possible.
PRINT / Content
On: print relevant content after weighing data
Gross – on: G; Net – on: N; Tare –
on: T;
Info – on: balance will print application
mode setting parameters
PRINT / Layout / Format - (Single,
Multi)
Single: print all data in one line
Multi: print all data in multiple lines
PRINT / Layout / Feed
-
(Line, 4 Lines,
Form)
Line: feed one line after printing
4 Lines
: feed four lines after printing
Form: feed one page after printing (move to the
top of next page after printing)
RS232 Interface EN-3
For STX Balances:
Upon installation, the STX balance will show RS232 icon ( ) in the upper right
corner.
Menu added
Function
Communication
|--
RS232
|--Baud Rate
|--Transmission
|--Handshake
|--
Print Settings
Set the baud rate (bits per second).
Set the data bits, stop bit, and parity.
Set the flow control method.
For more info, please refer to the STX instruction
manual.
EN-4 RS232 Interface
For PJX Balances:
Menu Navigation
PRINT
Header
Date and Time
Balance ID
Balance Name
User Name
Project Name
Application Name
Result
Gross Weight
Net Weight
Tare Weight
Line Feed
RS232
Baud Rate
Transmission
Handshake
Menu Settings
RS232 Interface Setup
--Baud Rate
--Transmission
--Handshake
Enter this sub-menu to customize RS232 standard settings.
Data may be output to either a printer or a PC.
Set the baud rate (bits per second).
1200 = 1200 bps
2400 = 2400 bps
4800 = 4800 bps
9600 = 9600 bps
19200 = 19200 bps
38400 = 38400 bps
Set the data bits, stop bit, and parity.
8-N-1 = 8 data bits, no parity, stop bit 1
8-N-2 = 8 data bits, no parity, stop bit 2
7-E-1 = 7 data bits, even parity, stop bit 1
7-E-2 = 7 data bits, even parity, stop bit 2
7-N-1 = 7 data bits, no parity, stop bit 1
7-N-2 = 7 data bits, no parity, stop bit 2
7-O-1 = 7 data bits, odd parity, stop bit 1
7-O-2 = 7 data bits, odd parity, stop bit 2
Set the flow control method.
NONE = no handshaking
XON-XOFF = XON/XOFF handshaking
HARDWARE = hardware handshaking
Print Settings
For more info, please refer to the PJX instruction manual.
RS232 Interface EN-5
RS232 (DB9) Pin Connections
The RS232 Interface Kit cable terminates with a 9 pin Sub-D female connector.
Active pins: Pin 2 = TXD, Pin 3 = RXD, Pin 5 = Ground.
The Interface connector can connect directly to a computer, an OHAUS printer and
other printers.
Diagram
Type
Description
Note: RTS
, CTS and
RT_CTL signal pins are only
available for PJX
balances
.
Interface type
Voltage interface conforming to EIA RS-
232C/DIN 66020 (CCITT V24/V.28)
Max. cable length
15 m
Signal level
Output:
+5 V ... +15 V (RL = 3 – 7kΩ)
-5 V ... -15 V (RL = 3 - 7 kΩ)
Input:
+3 V ... +25 V
-3 V ... -25 V
Connector
Sub-D, 9-pole, female
Operating mode
Full duplex
Transmission mode
Bit-serial, asynchronous
Transmission code
ASCII
Baud rates
Scout STX, SPX, SKX, SJX balances:
1200, 2400, 4800, 9600,
19200, 38400, 57600, 115200
(firmware selectable)
PJX balances:
1200, 2400, 4800, 9600, 19200, 38400
(firmware selectable)
Bits/parity
7-bit/even, 7-bit/odd, 7-bit/none, 8-bit/none
(firmware selectable)
Stop bits
Stop bit 1, 2
Handshake
None, XON/XOFF, RTS/CTS (selectable)
End-of-line
Not selectable
EN-6 RS232 Interface
RS232 OUTPUT
With the interface installed the balance will operate in several ways according to the
settings.
Print format can be switched by xFMT user command (see command table in
RS232 INPUT section).
New Scout Print Format (Default Format):
Output String (Non Check Weighing Applications):
[weight] 11 characters (right justified)
[space] 1 character
[unit] 5 characters (right justified)
[space] 1 character
[stability indicator] 1 character; "?" when unstable, space when stable
[space] 1 character
[T/N/G/PT] 2 characters (right justified)
[Term] 2 characters
Note: All of the fields have fixed length.
Output example:
*****192.21_****g_*_**
*******0.01_****g_?_**
*******95.0_****g_*_*N
******169.6_****g_*_*G
*******95.0_****g_*_*N
*******74.6_****g_*_*T
A.Print: off; Stable: off
Stable reading
unstable reading
A.Print: off; Stable: on
Content / Result -> on
Content / Gross -> on
Content / Net -> on
Content / Tare -> on
Output String (Check Weighing Application):
[weight] 11 characters (right justified)
[space] 1 character
[unit] 5 characters (right justified)
[space] 1 character
[stability indicator] 1 character; "?" when unstable, space when stable
[space] 1 character
[T/N/G/PT] 2 characters (right justified)
[space] 1 character
[application status] 6 characters (right justified)
[Term] 2 characters
Example:
RS232 Interface EN-7
*****
192.21_****
g_*_**_Accept
******
*0.01_****g_
?_**__Under
A.Print: off; Stable: off
Stable reading,
Unstable reading
Scout Pro Print Format 1 (for the models 303/123/202/402/602/2001/6001/
401FZH/601FZH/6000FZH):
Output String:
[weight] 12 characters (right justified)
[space] 1 character
[unit] 5 characters (left justified)
[space] 1 character
[stability indicator] 1 character; "?" when unstable, space when stable
[Legend] 1~10 characters
Output example:
********0.00_g****_*
*******12.73_g****_?
********0.85_oz***_WET
*WT
Scout Pro Print Format 2 (for the models 401/601/6000):
Output String:
[weight] 11 or 12 characters (right justified)
[space] 1 character
[unit] 1~5 characters
[space] 1 character
[stability indicator] 1 character; "?" when unstable, space when stable
[space] 1 character
[Legend] 1~10 characters
Note: The unit field length varies with different units. The weight field could be
11 or 12, depending on if the weight string has a dot or not.
Output example:
*********100_g_*_
*********
273_g_?_
*********8.5_oz***_WET*WT
EN-8 RS232 Interface
Print Format 3 (for Certain POS Systems):
Output String:
[weight] 11 characters (right justified)
[space] 1 character
[unit] 5 characters (right justified)
[stability indicator] 1 character; "?" when unstable, space when stable
[Term] 2 characters
Note: All of the fields have fixed length.
Output example:
PJX Print Format˖
˖
The Result Data, and G/N/T data, is output in the following format.
Field:
Label
Space
Weight
Space
Unit
Space
Stability
Space
G/N
Space
Term.
Characters
Length:
1
11
1
5
1
d 1
d 1
d 3
0
d 8
*******0.00_****g*
******12.73_****g?
Andere Handbücher für RS232
5
Inhaltsverzeichnis
Sprachen:
Andere OHAUS Adapter Handbücher
