OJ Electronics WLCT Bedienungsanleitung

Type WLCT

USER MANUAL

57541 09/04 - (BJ)

Type: WLCT

Fig. 1 - Buttons Display symbols

F:E:

B: C:

Pin button

adjust of

clock

Reset to

factory

setting

Adjustment

down OK -

Adjustment

Display

G: H: I:

J: K:

Automatic

mode Manual

mode Time and

temperature

Day number 4-event symbol

1. Getting started

Introduction

The clock thermostat type WLCT is part of the underfloor heating system type WLM. The thermostat can be set to control one single room, or it can be set

as a master to control a group of thermostats / rooms/zones.

All the thermostats that are part of that group will follow the times and temperatures programmed into the clock thermostat. For example, if the temperature

programmed in the clock thermostat is 22°C, all the thermostats / rooms belonging to that group will then also be controlled at 22°C. Depending on the

types of thermostats used you can adjust the temperature + or -4°C in different rooms, giving a possible room setpoint of +18 to +26°C.

The clock thermostat can be programmed to work at different temperatures during the day allowing lower temperatures during times that the room is

unoccupied. Lower temperatures will lower your energy costs without reducing the comfort. All thermostats that are part of the group will follow any new

time or temperatures programmed in the clock thermostat.

When it leaves the factory, the thermostat has a preset program suitable for most installations.

You only need to set the clock and day, and define the thermostats / rooms that should belong to the group.

The thermostat has a pin button marked R (see fig. 1), allowing you, at any time, to reset the thermostat to the factory settings. These are listed at the end of

this manual with space for you to record your own weekly schedule.

Setting the thermostat into operation

☞

1-7

Press the UP ( ) or DOWN ( ) buttons to select

the correct hours and press OK button ( ).

Press the UP ( ) or DOWN ( ) buttons to select

the correct minutes and press OK button ( ).

Then press the UP ( ) or DOWN ( ) button to

select the correct day and press OK ( ) button.

First time power is connected the clock and day will be flashing and must be set. If you need to

adjust the time of the thermostat at a later date, insert a pin into the hole marked (see fig. 1)

for setting of time and day. Adjustment should be made for change in summer and winter time.

Wake

Night

Out

Home

2. Daily use of the thermostat

4-event clock mode

The day has been split into 4 events describing a typical day. When the thermostat is in this 4-event mode it will change the temperature to the required level

automatically at the programmed times. As standard the thermostat has 5 days with 4 events (two ON’s and two OFF’s), and 2 days with 2 events (one ON

and one OFF). For programming see 3. Please, refer to item 4-PRO to alter the daily event sequence.

4-event clock mode/

automatic mode:

Comfort mode:

☞

☞

Manual mode:

☞

☞

Temporary override

To temporarily override any temperature in the 4-event schedule program, press the UP ( ) button once, to show

the temperature in the display, and press UP ( ) or DOWN ( ) again to increase or decrease the temperature.

The display will flash for 5 seconds, and will then revert to the time. The override will operate until the next

programmed event when the thermostat will resume the automatic programme.

In automatic mode, the clock function symbol ( ) and one of the 4-event symbols ( ) will be

indicated. Programming see 3.

Cancel comfort mode

To cancel the temporary override, press the OK ( ) button twice.

Permanent override:

During holidays, the scheduled 4-event program can be overridden.

Press the OK ( ) button, and then the UP ( ) or DOWN ( ) button until the override temperature is set. The set

temperature will remain in the display and the unit will now operate to this temperature permanently.

Cancel manual mode

To cancel the permanent override state press the OK ( ) button once, and the unit will resume automatic function.

5 secs.

☞

Press OK ( ) button for 3 secs. to begin programming

: Time and temperature

Day 1 - 5

Day 6 - 7

☞ ☞

: Time and temperature

☞ ☞

: Time and temperature

3. Programming

4-event time and temperature

For each event, the start time and required

temperature needs to be set.

For example, in the morning you wish the heating to

start at 07:00 and the temperature to rise to 25˚C.

Press OK ( ) button for 3 seconds and the start time

is displayed. Change this to 07:00 with the

UP ( ) or DOWN ( ) button. Press OK ( ) to

confirm.

The temperature is now displayed. Change this to 25˚C

with the UP ( ) or DOWN ( ) button.

Press OK ( ) button to confirm. This action can now

be repeated for the second, third and fourth event.

These settings will be valid for days 1-5 showing on

the display. To program the days 6 and 7, repeat the

above. Days 6 and 7 are usually Saturday and Sunday,

and only have two events (generally morning ON and

evening OFF).

The temperature can be set within the range of +5 to

+35˚C. It is also possible to select the heating OFF at

that event by reducing the setting to 5˚C, and then

pressing the ( ) once more.

Note that when programming the “Sleep” time

(event 4), please ensure that this time is before

midnight (00:00).

INFO - Information

The values of the actual measured room temperature and the floor temperature can be seen.

The floor temperature is only shown if a floor sensor is installed.

4. Advanced settings and read-out

PRO - 4-event sequence

It is possible to change the factory event sequence of Days 1-5 - 4 event, and days 6 & 7 – 2 event. Days 1 to 5 are usually Monday to

Friday, whilst days 6 & 7 are usually Saturday & Sunday. An EVENT is either an ON or an OFF operation. You can select from the

following sequences which are displayed in the form of a code.

☞✚

☞

4 events 5 days, 2 events 2 days indicated by Code 4:52

4 events 6 days, 2 events 1 days indicated by Code 4:61

4 events 7 days indicated by Code 4:70

2 events 7 days indicated by Code 2:70

2 events 5 days, 2 event 2 days indicated by Code 2:52

Select the required sequence with the OK ( ) button.

☞

Hi Li - Floor sensor. Max and min allowed temperature of the floor surface

A limit sensor can be connected to the clock thermostat.

Max limitation is used for safety to prevent high floor temperatures. For example wooden floor constructions which should not be

allowed to exceed a maximum of 27°C. The value can be set from 5°C up to 55°C. The value can also be set to OFF (adjust the

temperature to 55°C and push button up once more).

Low limitation is used where the temperature of the floor is required never to fall below the minimum set temperature. Example in

kitchens or bathrooms with tiles. The value can be set from 5°C up to 55°C. The value can also be set to OFF (adjust the

temperature to 5°C and push button down once more). Remember the max limit temperature must be set higher than the min limit

temperature.

The limit temperatures defined in the clock thermostat will be valid for all the thermostats with limit sensor (type WLTD-19) which

are part of the group of thermostats allocated to the WLCT unit.

SCAL - Time and temperature scale selection

☞

The maximum allowable floor temperature setting is shown. Use

the UP ( ) or DOWN ( ) button to increase or reduce, and OK

( ) button to accept.

The display will now show LoLi. Press OK ( ) button to continue.

The minimum allowable floor temperature setting. Use the UP ( )

or DOWN ( ) button to increase or reduce and OK ( ) button to

accept.

You can select either ˚C or ˚F scale, and 12 or 24 hour clock as

follows:

Press UP ( ) or DOWN ( ) button to change settings. Confirm

the required scale with the OK button ( ) button.

☞

Press both UP ( ) and DOWN ( ) buttons together for 3 seconds. INFO is displayed.

Continue pressing the UP( ) button until you reach one of the desired sub menus, PRO, Hi Li, Scal, and ArEA (For explanations, see

below. Select the sub menu with the OK ( ) button.

Press UP ( ) or DOWN ( ) button to show the different

readouts.

No changes can be made here. Use the OK ( ) button to end.

Software version

Room temperature

Floor temperature

☞

}

Press the pin button R for 3 secs. and the thermostat returns to

factory settings.

Remember to set time, day and area zone.

5. Reset to factory setting

OJ ELECTRONICS A/S

Stenager 13B · DK-6400 Sønderborg

Tel. +45 73 12 13 14

Fax +45 73 12 13 13

[email protected] · www.oj.dk

4-event time and temperature

Day 1-5

06:00

Time Own settings Temperature Own settings

08:00

16:00

22:30

08:00

23:00

27ºC

4:52

4-event sequence

Day 6-7

20ºC

15ºC

22ºC

15ºC

22ºC

15ºC

Factory settings

High limit

temperature

Low limit

temperature

Scale

17ºC

24H,ºC

Group

Off

Kitchen

Living room

Room

Ch 1

Ch 2

Ch 3

Ch 4

Ch 5

Ch 6

Ch 7

Ch 8

Ch 9

Ch 10

Ch 11

Ch 12

Ch 13

Ch 14

Example

Ch 1

Ch 2

Insert the room name in the box against each Ch number,

and add ON if it is controlled by a clock thermostat.

Set the Channels / Rooms (Ch) to ON if they should follow the

settings of this clock thermostat.

In total 14 channels / rooms can be controlled.

☞

Press OK ( ) button to end programming and to return to

scheduled programme.

☞

ArEA - Zone

The thermostats / rooms that are to be set as part of the WLCT group will follow the temperature settings of the clock thermostat. For

example, a group could be the living room kitchen, and children’s rooms having a high room temperature during afternoon and early

evening, and a lower temperature during the early part of the day and at night. Each thermostat will have a channel number,

designated CH1, CH2 etc. The appropriate channel number of any thermostat is determined by the numbered output on the master

control which is actually switching the valve/actuator for that area.

For example, a system may have the kitchen thermostat operating master output # 4, and the childrens room thermostat operating

master output #5. If the WLCT clock thermostat is then situated in the living room, and operating output #1, then the WLCT needs to

be programmed to control outputs 1, 4, & 5. ( Each non clock thermostat will have been set to operate its appropriate output channel,

see separate instructions).

To do this, enter the ArEA sub menu., and press OK ( ) button. CH 1 will be displayed; use the OK ( ) button and then the UP ( )

button to change the setting to ON. Press OK ( ) and CH 2 is displayed. Use the UP ( ) button until CH4 is displayed, press OK ( ),

and change to ON. Repeat this for CH 5. All three thermostats will now operate under the control of the WLCT clock thermostat.

In total up to 14 Channels can be programmed in this way, and it is possible to have more than a single clock thermostat, each with its

own sub thermostats operating to its schedule and temperatures.

57541

Inhaltsverzeichnis

Andere OJ Electronics Thermostat Handbücher

OJ Electronics

OJ Electronics OCC4 Bedienungsanleitung

OJ Electronics

OJ Electronics UDG4 Bedienungsanleitung

OJ Electronics

OJ Electronics UCCG-4991 Bedienungsanleitung

OJ Electronics

OJ Electronics ETR Series Bedienungsanleitung

OJ Electronics

OJ Electronics MWD5-1999-UAC3 Bedienungsanleitung

OJ Electronics

OJ Electronics ETN4-1999 Bedienungsanleitung

OJ Electronics

OJ Electronics OCD6-1999 Bedienungsanleitung

OJ Electronics

OJ Electronics ETV Series Bedienungsanleitung

OJ Electronics

OJ Electronics ETR2 Bedienungsanleitung

OJ Electronics

OJ Electronics UCG Bedienungsanleitung

OJ Electronics

OJ Electronics OJ Microline ICD3-1999 Bedienungsanleitung

OJ Electronics

OJ Electronics MICROLINE OTN2 Bedienungsanleitung

OJ Electronics

OJ Electronics UTN4 Bedienungsanleitung

OJ Electronics

OJ Electronics UWG4 Bedienungsanleitung

OJ Electronics

OJ Electronics OJ Microline ICD3-1999 Bedienungsanleitung

OJ Electronics

OJ Electronics ETN4-1999 Bedienungsanleitung

OJ Electronics

OJ Electronics MTD3-1999 Bedienungsanleitung

OJ Electronics

OJ Electronics WLM2 Bedienungsanleitung

OJ Electronics

OJ Electronics UCG Bedienungsanleitung

OJ Electronics

OJ Electronics ETR2 Bedienungsanleitung

OJ Electronics

OJ Electronics MSD4-1999-UA Bedienungsanleitung

OJ Electronics

OJ Electronics MTC Series Bedienungsanleitung

OJ Electronics

OJ Electronics OCC4 Bedienungsanleitung

OJ Electronics

OJ Electronics UCCG Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung