Olympia electronics GR-939/30L/LT Bedienungsanleitung

GENERAL

This luminaire is used in places with low

temperature (-20 C) where emergency

luminaires are needed.

Each illumination sign must be permanently

connected to mains power supply. In normal

operation the led strip lights and the battery is

charging. In case of a mains power supply

failure the illumination sign will light the led

strip automatically in emergency mode. When

the mains power supply is restored the device

turns to normal operation.

INSTALLATION

To install the luminaire follow the installation

instructions on page 3.

Battery Charging

The battery charging is completely controlled.

In this case, is achieved the perfect battery

maintenance, as well as the elongation of its

duration. When the battery has completely

charged, it charges with a maintenance

current.

Battery Cut-off

The luminaire enters in this operation when the

mains power supply fails and battery has lost

its energy. During this operation the

illumination sign enters the idle state and

battery consumption is negligible, in order to be

protected from deep discharge.

Manual Test

The manual test can be conducted only if the

mains power supply and the battery is

connected. By pressing the TEST/RESET

button briefly (page 3) an emergency operation

test is initiated. During this test period all

indication LEDs are OFF.

Automatic Operational Test

This test includes all the operations that provide

the manual test and is conducted automatically

every 15 days. In order to be performed, the

mains power supply and the battery should be

connected.

Manual Autonomous Test

If the Test button is pressed for a period

between 5 to 10 seconds (with the battery fully

charged), the illumination sign will enter in

counting autonomy condition. If the battery is

not fully charged this command is ignored. The

BATTERY FAULT blinks during the

measurement, indicating this process to the

user. This measurement duration is equal with

the nominal autonomous duration of the

illumination sign (1.5 hour or 3 hours) and at the

end of the process, if the measured duration

was at least the nominal autonomous duration,

the BATTERY FAULT is turned OFF, in the other

hand stays continuously ON indicating to the

Page 1 from 5 923939016_09_007

WATERPROOF SELF TESTING MAINTAINED EMERGENCY LUMINAIRES

ΤΕΧΝΙΚΑ ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ

90 min

Charge, Lamp fault, Battery fault , TEST button

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3

31W / 33VA (<0°C)

3.6V / 2Ah

GR-938/30L/LT

180 min

24h

From overcharge and deep discharge

4 years

IP65

280lm / 230lm

White LEDs

-20 to +40 C

Up to 95%

Bayblend FR3010, transparent polycarbonate

3 years (1 year for the battery)

940gr. 1050gr.

32W / 35VA (<0°C)

3.6V / 4Ah

220-240VAC 50-60Hz

363 x 145 x 73 mm

GR-939/30L/LT

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

EXTERNAL DIMENSIONS

CONSTRUCTION MATERIALS

TYPICAL WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

CHARGING TIME

INDICATIONS - CONTROLS

BATTERY PROTECTION

EXPECTED BATTERY LIFETIME

MINIMUM AUTONOMOUS DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

ILLUMINATION (MAINS / EMERGENCY)

ILLUMINATION SOURCE

BATTERIES (Ni-ΜΗ)

TECHNICAL CHARACTERISTICS (for LED MODULE Specifications see page 4)

Thank you for your trust in our products.

Olympia Electronics - European manufacturer.

Page 2 from 5

user that the battery must be replaced.

Automatic Autonomous Test

The Automatic Autonomous Test is conducted

and measures the illumination sign’s back up

operation and emergency duration. This test is

conducted automatically every six months. In

order to be performed, the mains power supply

and the battery should be connected and fully

charged. If the battery is not fully charged, the

test is postponed until the battery is

completely charged. If during the Automatic

Autonomous Test the luminaire’s duration is

lower than the nominal, then the battery must

be replaced.

Back Up Operation

The autonomous duration of battery during

emergency mode is at least the one that is

stated in the list of the technical

characteristics. During emergency mode, a

LED strip test is also performed.

Resetting Errors

Push continuously the TEST/RESET button for

>10 seconds, to delete all the indicated LED

errors . Then the luminaire enters regular

operation mode.

Test Switch (Briefly)

Pressing the test switch less than 5 seconds

will initiate a light source test (last for 3 secs).

Pressing the test switch between 5 to 10

seconds will initiate a manual battery duration

test. This test will not be started if the battery

is not fully charged (i.e. If the green LED is

flashing). If the test switch is pressed for more

than 10 seconds, the device will delete all

errors).

ΑΤΤΕΝΤΙΟΝ!!!

1. Operations for installation, maintainance or

testing must be done by authorized personnel

only.

2. The device must be connected to the mains

power supply through a fuse dependent by the

total amount of the line’s power load.

3. In case of battery or lamp replacement, these

must be replaced by parts of the same type, by

the manufacturer or by a competent person.

4. In case of inactive use for a period

greater than 2 months, disconnect the

battery by pulling out the battery’s

connector.

5. I s not allowed to discard batteries in to t i

common trash bins, they must be discarded

only in battery recycling points. Do not

incinerate.

Battery Replacement

1. Unfasten the 4 retaining screws (step 8 of the

installation instructions) and remove the

diffusor.

2. Unfasten the 2 retaining screws step 7 of the

installation instructions and remove the

reflector.

3. Remove the old battery and place a new on

of the same type and characteristics.

4. Replace the removed parts (previous steps

1,2).

Important notice for the installed luminaires

in one area !!!

The installer must connect the battery’s

connector first and then should power the

luminaire. The batteries connection must have at

least a time variation of 1.5 minute for each

luminaire. With this variation, it is ensured that the

non synchronized Automatic Autonomous Test

for two or more luminaires installed in one area, is

not conducted in the same day.

923939016_09_007

(*) Non Maintained operation: The luminaire lights its illumination source, only in power supply’s

failure.

Maintained operation: The luminaire lights its illumination source, when it is powered by the mains

power supply or not.

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained

1: Maintained (*)

A: Including test device

G: Internally illuminated

*90: 1.5 hour duration

180: 3 hours duration

Note!! The installer should fill in, on the specification label,

the letter G if the luminaire is used as a safety sign.

X 1 9 0A G

Page 3 from 5

INSTALLATION INSTRUCTIONS

Step 1. Remove the diffusor. Place a flat blade screwdriver and pull the reflector gently (with

opposite orientation in relation to the plastic base).

Step 2. Install the included plastic cover in to the unused hole and install the base plastic (with

the included mounting screws and plugs).

Step 3. Always use in any case round mains cable, with a diameter of 6-9mm (H05RN-F

type 2x1mm² or any other type, at least equal to it’s mechanical and electrical properties).

ATTENTION!! The cable must not be deformed in any way (This requirement is important

to ensure the tightness isolation IP65). Install the cable gland, pass the round cable thru and

tighten it all the way. When fastening the cable gland retain the main body of the gland in a

steady position and rotate only the internal plastic screw, this will prevent the rubber grommet

from being damaged.

Step 4. Place the battery’s connector to the corresponding connector on the P.C.B.

Step 5. Connect the mains cables to the respective terminal block (connect the ground wire if

required). Ν for neutral, L for Live Wire and L1 for the maintained operation. The L1 wire

can be connected to an external switch to control the maintained or non maintained operation of

the luminaire. For permanent maintained operation use two wires to power the luminaire, Ν for

neutral and L for Live Wire, and Link the L and L1.

Step 6. Install the included tie (if needed) to fasten securely the power cables.

Step 7. Refit the reflector and fasten the two small screws (included).

Step 8. Finally place the diffusor by using the 4 screws (tightening torque 1.2Nm).

Step 9. Manual TEST or Resetting Errors

In order to test or reset the device you must carefully remove the diffusor by unfastening the 4

mounting screws. Then push the button as described in the according paragraphs on page 1 and

NOTE!! After finishing the installation you must power the luminaire at least for 24 hours

for battery charging to perform the nominal autonomy.

923939016_09_007

L1 L N

2 3

Page 4 from 5 923939016_09_007

Status of LEDs

Led status explanation

GREEN

YELLOW

RED

Normal

Charging

Battery duration test (auto or manual)

Battery fault

Battery fault and light source fault

Charger and battery fault (or mains off and battery fault)

Charger and light source fault (or mains off and light source fault)

Charger, battery and light source fault (or mains off, battery and light source fault)

1Hz: Heating circuit fault

5Hz: Open circuit of heating resistors

Light source test

Light source fault

Steady ON Steady OFF Flashing in 1Hz or 5Hz

Charger fault, battery not connected

or mains off

LEDs Description

The heating circuit faults are:

1) Open circuit of the heat sensor.

2) Short circuit of the heat sensor.

3) When the heated area is >50 C. All the above faults are indicated as long as they

exist. When they are restored, they will be erased and not indicated by the indication

LEDs.

LED MODULE CHARACTERISTICS

Olympia Electronics S.A

45 °C max. across the board

Cable connection with non-reversible connectors

14-16.5V DC

5.4W

GR-938/30L/LT GR-939/30L/LT

0505175/30L

Manufacturer

Model Number

Voltage Range

Connections

Nominal Power

Temperature (tc)

Page 5 from 5 923939016_09_007

WARRANTY

Olympia Electronics guarantees the quality, condition and operation of the goods. The period of

warranty is specified in the official catalogue of Olympia Electronics and also in the technical leaflet,

which accompanies each product. This warranty ceases to exist if the buyer does not follow the

technical instructions included in official documents given by Olympia Electronics or if the buyer

modifies the goods provided or has any repairs or re-setting done by a third party, unless Olympia

Electronics has fully agreed to them in writing. Products that have been damaged can be returned to

the premises of our company for repair or replacement, as long as the warranty period is valid.

Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge

the buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or

not the buyer the transportation cost.

HEAD OFFICE

72nd km. O.N.R. Thessaloniki-Katerini

P.C. 60300 P.O. Box 06 Εginio Pierias Greece

www.olympia-electronics.gr

[email protected]

The light source contained in this luminaire shall only be replaced by the manufacturer, or his

agent, or a similar qualified person.

NOTE! The light source is non-user replaceable.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere olympia electronics Laterne Handbücher

olympia electronics

olympia electronics WEATHER LIGHT Series Bedienungsanleitung

olympia electronics

olympia electronics GR-938/15L Bedienungsanleitung

olympia electronics

olympia electronics OLY-1004/WP/ADR Bedienungsanleitung

olympia electronics

olympia electronics GR-220/DUO/M Bedienungsanleitung

olympia electronics

olympia electronics GR-2100/ST Bedienungsanleitung

olympia electronics

olympia electronics GRL-37/90/ADR Bedienungsanleitung

olympia electronics

olympia electronics Classic Light Series Bedienungsanleitung

olympia electronics

olympia electronics GR-290/WP/M Bedienungsanleitung

olympia electronics

olympia electronics GRL-38/90/M Bedienungsanleitung

olympia electronics

olympia electronics GR-270 Bedienungsanleitung

olympia electronics

olympia electronics GR-490/ADR Bedienungsanleitung

olympia electronics

olympia electronics GR-108/12L/90 Bedienungsanleitung

olympia electronics

olympia electronics Slim Light Series Bedienungsanleitung

olympia electronics

olympia electronics GR-290/M Bedienungsanleitung

olympia electronics

olympia electronics GR-1935/15L Bedienungsanleitung

olympia electronics

olympia electronics LLB-26/90 Bedienungsanleitung

olympia electronics

olympia electronics GR-490/WP/ADR Bedienungsanleitung

olympia electronics

olympia electronics GR-427/12L/MAR Bedienungsanleitung

olympia electronics

olympia electronics KLIN-20/ST/ADR Bedienungsanleitung

olympia electronics

olympia electronics GRL-37/90/WP Bedienungsanleitung

olympia electronics

olympia electronics EASY LIGHT Series Bedienungsanleitung

olympia electronics

olympia electronics OLY-1004 Bedienungsanleitung

olympia electronics

olympia electronics BAU LIGHT Series Bedienungsanleitung

olympia electronics

olympia electronics WATERPROOF POWER LIGHT Series Bedienungsanleitung

Beliebte Laterne Handbücher anderer Marken

KYOWA

KYOWA KW-9114 Bedienungsanleitung

Stahl

Stahl ECOLUX 6610 Series Bedienungsanleitung

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Bedienungsanleitung

PRG

PRG VARI LITE VL5 Bedienungsanleitung

Raytec

Raytec VARIO2 series Bedienungsanleitung

ENSA

ENSA LEDBT18WS2 Bedienungsanleitung

LUG

LUG OFFICE LB LED N/T Bedienungsanleitung

GE Wallighter 250 Bedienungsanleitung

Draper

Draper RLEDL19/B Bedienungsanleitung

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Bedienungsanleitung

Panasonic

Panasonic EY3741B57 Bedienungsanleitung

Clas Ohlson

Clas Ohlson LCC8T Bedienungsanleitung

Coolon

Coolon WDN-140 Bedienungsanleitung

Holiday Travel

Holiday Travel 834873 Bedienungsanleitung

BEGA

BEGA 84 036 Bedienungsanleitung

BEGA

BEGA 33 596 Bedienungsanleitung

Dale Tiffany

Dale Tiffany GT701162 Bedienungsanleitung

Wagan

Wagan Brite Nite Pop-Up USB Lantern Bedienungsanleitung

olympia electronics GR-939/30L/LT Bedienungsanleitung

Beliebte Laterne Handbücher anderer Marken