Olympia electronics GR-423/12L/MAR Bedienungsanleitung

Thank you for purchasing this product of

Olympia Electronics. A European

manufacturer.

GENERAL

These luminaires are suitable for marine and

offshore applications where emergency light

is needed. Each luminaire must be

permanently connected to mains power

supply.In normal operation the led strip lights

and the battery is charging. In case of a

mains power supply failure the luminaire will

light the led strip automatically in emergency

mode. When the mains power supply is

restored the device turns to normal operation.

INSTALLATION

To install the luminaire follow the installation

instructions on page 4.

Battery Charging

The battery charging is completely controled.

In this case, is achieved the perfect battery

maintenance , as well as the elongation of its

duration. When the battery has completely

charged, it charges with a maintenance

current.

Battery Cut-off

The luminaire enters in this operation when

the mains power supply fails and battery has

lost its energy. During this operation the

luminaire enters the idle state and battery

consumption is negligible, in order to be

protected from deep discharge.

Manual Test

The manual test can be conducted only if the

main power supply and the battery is

connected. By pressing the test button briefly

an operation test is initiated. During this test

period all indication LEDs are OFF.

Automatic Test

This test includes all the operations that

provide the manual test and is conducted

automatically every 15 days. In order to be

performed, the main power supply and the

battery should be connected.

Automatic Autonomous Test

The Automatic Autonomous Test is conducted

and measures the luminaire`s back up

operation. This test is conducted automatically

every six months. In order to be performed,

the main power supply and the battery should

be connected (the battery should be charged).

If the battery is not charged, the test is

postponed until the battery is completely

charged. If during the Automatic Autonomous

Test the luminaire’s duration is lower than the

nominal, then the battery must be replaced.

Back Up Operation

The autonomous duration of battery during

emergency mode is at least the one that is

923423012_09_002

Page 1 from 4

SELF TESTING MAINTAINED EMERGENCY LUMINAIRES

220-240V AC/50-60Hz

3W / 6.5VA 4W / 7VA

Bayblend FR3010, transparent polycarbonate

TECHNICAL CHARACTERISTICS

OPERATION TEMPERATURE RANGE

RELATIVE HUMIDITY

EXTERNAL DIMENSIONS

CONSTRUCTION MATERIALS

TYPICAL WEIGHT

GUARANTEE

OPERATION VOLTAGE

MAXIMUM POWER CONSUMPTION

BATTERIES (Ni-Cd)

CHARGING TIME

INDICATIONS - CONTROLS

BATTERY PROTECTION

MINIMUM AUTONOMOUS DURATION

DEGREES OF COVER PROTECTION

PRODUCED IN ACCORDANCE WITH

ILLUMINATION (230V / EMERGENCY)

ILLUMINATION SOURCE 180min

24h

Charge, lamp fault, fault indication LED, TEST button

From overcharge and full discharge

IP 42

3.6V/1Ah

85/85lm 170/170lm

12 white LED’s 24 white LED’s

5 to 40 C

Up to 95%

3 years (1 year for the battery)

480gr. 272 x 121 x 50 mm

GR-423/12L/MAR GR-423/24L/MAR

3.6V/2Ah(NiMH)

560gr.

High Quality European based Manufacturers

EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3, IEC 60092-306, IEC 60533

Page 2 from 4

stated in the list of the first page. During

emergency mode, a LED strip test is also

performed.

Resetting Errors

Push the Test button for 5 seconds, to

extinguish all the indicated LED errors. Then

the luminaire enters regular operation mode.

Indication LED status (with connected

mains power supply).

Charge

On: Good charge current.

Οff: No battery (No charging current or

disconnected battery).

Lamp Fault

Οn: Faulty LED strip.

Off: Good LED strip.

Battery Fault

Οff:Battery OK.

Blink (With Charge LED ON): Autonomy or

low battery problem

(the battery must be replaced).

Blink (With Charge LED Off):

No charging current or disconnected battery.

ΑΤΤΕΝΤΙΟΝ!!!

1. Operations for installation, maintainance or

testing must be done by authorized personel

only.

2. The device must be connected to the mains

power supply thru a fuse dependent by the

total amount of the line’s power load.

In case of battery or light source replacement,

these must be replaced by parts of the same

type, by the manufacturer or by a competent

person.

t i

in battery recycling

points. Do not incinerate.

4. In case of inactive use for a period greater

than 2 months, disconnect the battery by

pulling out the battery’s connector.

5. I s not allowed to discard batteries in to

common trash bins, they must be

discarded only

Suspended ceiling

Α-3018 mounting springs

Mounting methods

All luminaires, can be mounted either surface or in

suspended ceilings.

Suspended ceiling installation.

On the bottom of the base plastic of the luminaire

there are two Hshaped cut outs. These are used to

install the A-3018 mounting springs.

1. With a sharp tool remove the appropriate plastic

pieces to fit the mounting springs. First place the

edges of the mounting spring to the respective holes

and install the one end of the coil to the support axis.

2. Install the other end of the coil to the other support

axis.

3. Bend the springs and place the luminaire to the

respective suspended ceiling’s hole.

The luminaire’s placement to the suspended ceiling

must be done after the connection with power supply

cables. Mounting the luminaire

in a suspended ceiling

Required

opening in

a suspended

ceiling

260

110

923423012_09_002

Page 3 from 4 923423012_09_002

Installation methods

A-3018

Special mounting

springs for

suspended ceiling

installation

Mounting springs Α-3018

Wall or ceiling installation

Suspended ceiling installation

MARKING PANEL SP-115

A marking panel SP-115 can be installed on

the luminaire in 3 different locations. This

marking panel is installed perpendicular to the

diffusor of the luminaire, as shown in the

pictures below. The panel is pre-printed and

has a plastic accessory on each side that is

used to fasten the panel to the luminaires.

There are 2 arrow stickers that can be placed

in each side of the marking panel to point to

the desired direction.

Placing the SP-115 marking panel

Place the plastic mounting accessories of the

marking panel as shown in pictures.

A-3018

SP-115 marking panel

Suspended ceiling installation

with Α-3018 mounting springs

and SP-115 marking panel

Ceiling installation

with SP-115 marking panel

Wall installation with SP-115

marking panel

923423012_09_002

Page 4 from 4

45 6

INSTALLATION INSTRUCTIONS

Base plastic

Cable entry channels

Luminaire mounting holes

Diffusor

Reflector

Base plastic

LL1

1 To install the luminaire you must dismantle it into 3 parts.

2 Place a flat blade screwdriver in the area Α to release the diffusor’s

plastic hook.

3Place a flat blade screwdriver in the area Bto release the reflector’s

plastic hook.

4 Use the included mounting parts to mount the base plastic.

Pass the mains cable through a cable entry channel. The luminaire

must be connected to a permanent electrical installation to ensure the

immobilization of the cable.

5 Place the battery’s connector to the corresponding connector on the

P.C.B.

6 Connect the mains cables to the respective detachable terminal

block. Ν for neutral, L for live wire and L1 for the maintained

operation. The L1 wire can be connected to an external switch to

control the maintained or non maintained operation of the luminaire.

For permanent maintained operation use two wires to power the

luminaire, Ν for neutral and L for live wire, and link the L and L1.

7 Refit the removed parts in steps 2 and 3 (mind the correct

orientation) and the luminaire is ready to operate.

External

switch

Link

Controled operation of the luminaire

Permanent maintained operation

L L

L1 L1

NOTE!!

After finishing the installation you must power the luminaire at least for 24 hours for battery

charging to perform the nominal autonomy.

Battery replacement.

It can be done only by a competent person and after the mains interruption.

1. Follow the step 2 and 3 of the installation procedure.

2. Disconnect the connector and remove the old battery.

3. Connect the new battery with the same type (step 5 of the installation procedure) and place it in

the position of the old one.

4. Follow the step 7 of the installation procedure and power the device.

NOTE: LED= Light Emitting Diode

LABELING EXPLANATION:

X: Self contained 1: Maintained (*) A: Including test device 180: 180min duration

(*) Maintained operation: The luminaire lights its illumination source, when it is powered by the

mains power supply or not.

Non Maintained operation: The luminaire lights its illumination source, only in apower supply failure.

Dieses Handbuch passt für folgende Modelle

Andere olympia electronics Beleuchtungsausrüstung Handbücher

olympia electronics

olympia electronics ZLD-28/EM/MAR Bedienungsanleitung

olympia electronics

olympia electronics SLL-1001/WP Bedienungsanleitung

olympia electronics

olympia electronics KLD-30/ST/ADR Bedienungsanleitung

olympia electronics

olympia electronics PLD-25/NiMH Bedienungsanleitung

olympia electronics

olympia electronics GR-415/4P Bedienungsanleitung

olympia electronics

olympia electronics GRL-22 Bedienungsanleitung

olympia electronics

olympia electronics KLD-30/CBS/24V/ADR Bedienungsanleitung

olympia electronics

olympia electronics GR-460 Bedienungsanleitung

olympia electronics

olympia electronics GR-1938/15L Bedienungsanleitung

olympia electronics

olympia electronics SLD-28/SP Bedienungsanleitung

olympia electronics

olympia electronics MLD-28D/w/MAR Bedienungsanleitung

olympia electronics

olympia electronics ZLD-28/EM Bedienungsanleitung

olympia electronics

olympia electronics GR-60 Bedienungsanleitung

olympia electronics

olympia electronics GR-315/15L Bedienungsanleitung

olympia electronics

olympia electronics GR-940/15L Bedienungsanleitung

olympia electronics

olympia electronics ZLD-28/EM/ADR Bedienungsanleitung

olympia electronics

olympia electronics GR-316/15L/MAR Bedienungsanleitung

olympia electronics

olympia electronics GR-900/30L/SC Bedienungsanleitung

olympia electronics

olympia electronics TUV COMFORT LIGHT Series Bedienungsanleitung

olympia electronics

olympia electronics GRL-37/90 Bedienungsanleitung

olympia electronics

olympia electronics KLD-22/ST Bedienungsanleitung

olympia electronics

olympia electronics GR-938/30L Bedienungsanleitung

olympia electronics

olympia electronics GR-577/L/15/ST/WP Bedienungsanleitung

olympia electronics

olympia electronics GRL-29/WL Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

olympia electronics GR-423/12L/MAR Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken