Omnimount SAT 2 Bedienungsanleitung

STEP 1 – Prepare the stand base.

Place speaker stand base (a) upside down on ground. Locate steel

isolation spikes and adjustment nuts (e). Thread adjustment nuts

approximately half way onto the spikes, and then thread spikes into

three holes on the stand base, until adjustment nuts touch the base.

Use caution when handling stand base, as the isolation spikes are

sharp and can scratch wooden floors.

Assembly Instructions for SAT2 Speaker Stand

b - Outer

post.

d - Inner

post.

Fig. 3

Parts List

a - Base. (2) Allen wrench

e - Steel isolation

spikes and adjustment

nut. (6)

f - Clamping

mechanism. (2)

i - Foam dampening

pad. (4)

n - Double sided adhesive pads (8)

k - 5mm screw mounts

bracket and clamp mechanism

to inner post. (2)

l - M4 Base to post screw. (4)

c - Adjustable

post assembly

(2).

Speaker to

bracket mounting

screws

#8c

1/4-20 5mm 4mm #8 #8h

(g)

(h)

(m)

(o)

Base and keyhole

bracket

(Klipsch ProMedia)

45 deg.back

bracket (Klipsch)

90 deg.back

bracket

Angle bracket

(Klipsch)

Fig. 1

STEP 2 – Attach the post assembly.

Locate adjustable post assembly (c). Loosen set screw (see Fig. 3) on

back of outer post (b) using supplied Allen wrench.

Turn adjustable post assembly upside down and gently shake it until inner

post (d) becomes accessible. Pull inner post out approximately six inches.

Rotate inner post until speaker wire port is in line with set screw, and then

re-tighten set scre

re-tighten set screw.

Insert speaker wire into speaker wire port, run wire down through adjustable

post assembly, and then thread it through center hole in top of speaker base.

Be sure to leave enough slack at the ends so that wire doesn’t get pulled

out during remainder of assembly process. Attach adjustable post assembly

to speaker stand base with two base post screws (l), as shown in Fig. 1,

being careful not to pinch speaker wire. Make sure that speaker wire port is

pointing away from the front of the base, which is marked withpointing away from the front of the base, which is marked with

OmniMount label.

STEP 3 - Select the appropriate speaker adaptor. See Figure 2.

If your speaker comes with a threaded insert in the back or

on the bottom, use bracket (g), (h), (j), (m) or (o).

For brackets (h), (m) or (o), go to step 4.

For keyhole bracket (g), go to step 4.2.

If your speaker does not come with a mounting insert, you will need toIf your speaker does not come with a mounting insert, you will need to

use the clamping mechanism (f).

For clamping mechanism, go to step 4.1.

foam dampening

pads

move rails

all of the way

out

Fig. 4

Outer

post. (b)

Fig. 2

Set screw

Inner

post. (d)

side rails fit

snugly against

speaker equal distance

on both sides

side rails

knob

Fig. 5

Fig. 6 Fig. 7

Inner

post. (d)

mounting

screw(k)

Andere Omnimount Rack & Stand Handbücher

Omnimount

Omnimount 5.0 W/C Bedienungsanleitung

Omnimount

Omnimount OE150FM Bedienungsanleitung

Omnimount

Omnimount OM10046 Bedienungsanleitung

Omnimount

Omnimount VB150F Bedienungsanleitung

Omnimount

Omnimount CP-4 Bedienungsanleitung

Omnimount

Omnimount SB60C Bedienungsanleitung

Omnimount

Omnimount OCSBA Bedienungsanleitung

Omnimount

Omnimount WS-3 Bedienungsanleitung

Omnimount

Omnimount IES1 Bedienungsanleitung

Omnimount

Omnimount PRO-PJT Bedienungsanleitung

Omnimount

Omnimount OC80F Bedienungsanleitung

Omnimount

Omnimount 10067 Bedienungsanleitung

Omnimount

Omnimount CL-S Bedienungsanleitung

Omnimount

Omnimount PMD.5 Bedienungsanleitung

Omnimount

Omnimount OE80T Bedienungsanleitung

Omnimount

Omnimount OL80F Bedienungsanleitung

Omnimount

Omnimount 10048 Bedienungsanleitung

Omnimount

Omnimount RSF.5 Bedienungsanleitung

Omnimount

Omnimount SC120FM Bedienungsanleitung

Omnimount

Omnimount CI175T Bedienungsanleitung

Omnimount

Omnimount OMNI 25.0W Bedienungsanleitung

Omnimount

Omnimount CI40FML Bedienungsanleitung

Omnimount

Omnimount OM10012 Bedienungsanleitung

Omnimount

Omnimount OS50T Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung