Onicon F-4300 Montageanleitung

F-4300 Clamp-on Ultrasonic Thermal Energy Measurement System

Installation Hardware Instruction for Clamp-on Thermowells

CON

Flow and Energy Measurement

DOC-0004103 Rev.A

ONICON Incorporated • 11451 Belcher Road South • Largo, FL 33773 • USA • www.onicon.com

IMPORTANT NOTE

ONICON BTU meters are

precision measuring devices

that must be installed

according to the instructions

contained in this document

in order to maintain their

accuracy and reliability.

For Use with Kit: INSTL0501-TSC & INSTL0502-TSC

Please read entire manual before installing the meter.

The two temperature sensors must be located in such a manner

as to accurately measure only the temperature of the supply line

entering and the return line leaving the portion of the piping

system for which the energy measurement is being made.

If possible, nd an easily accessible location where wire

connections can be made from oor level. This will facilitate any

future service.

One temperature sensor thermowell will need to be placed in the same pipe as the mounting

brackets. If it is an immersion thermowell, it must be located on the downstream side of the mounting

brackets.

The downstream distance between the thermowell and brackets should be at least ve (5) pipe

diameters, leaving enough clearance to remove either sensor from the pipe without interference from

the other sensor.

IMPORTANT NOTE:

Place the temperature sensors away from strong sources of electrical noise that might aect the

performance of the sensors.

FLOW DIRECTION

CLAMP-ON FLOW METER

INSTALLATION LOCATION

CLAMP-ON

THERMOWELL ASSEMBLY

TYPICAL THERMOWELL INSTALLATION

F-4300 Clamp-on Ultrasonic Thermal Energy Measurement System

Installation Hardware Instruction for Clamp-on Thermowells

CON

Flow and Energy Measurement

DOC-0004103 Rev.A

ONICON Incorporated • 11451 Belcher Road South • Largo, FL 33773 • USA • www.onicon.com

Directions for Installation:

1. Remove junction box cover and set aside.

2. Attach the provided Velcro or the enclosure mounting hardware in the desired location as

shown below.

JUNCTION BOX COVER

PROVIDED VELCRO

727.447.6140 Page 3 onicon.com

CON

Flow and Energy Measurement

F-4300 Clamp-on Ultrasonic Flow Meters

Installation Hardware Instruction for Clamp-on Thermowell

3. Apply a thin coat of thermal compound to the temperature sensor, and gently insert the

temperature sensor all the way into the clamp-on thermowell.

4. Apply thermal compound to the heat sink and install the clamp-on thermowell on to the pipe

using the pipe strap as shown.

Directions for Installation (Continued):

11451 Belcher Road South • Largo, FL 33773 • USA • (P) 727.447.6140 • (F) 727.442.5699 • onicon.com

CON

Flow and Energy Measurement

5. Connect the Signal (+) and Reference (-) wires from the transmitter to the F-4300 BTU meter

through the strain relief. Be sure to observe the polarity of the connection, positive to positive

and negative to negative. Shield wires should be connected at the F-4300, but left open at the

temperature sensor transmitter.

TRANSMITTER

STRAIN RELIEF

6. Tighten the strain reliefs and reinstall the junction box cover. Once the thermowells and sensors

are fully installed and tested, insulate the thermowells and the pipe to complete the installation.

Directions for Installation (Continued):

If you have any questions or need assistance, please contact ONICON Sales at (727) 447-6140 or

[email protected].

Andere Handbücher für F-4300

Andere Onicon Messgerät Handbücher

Onicon

Onicon SYSTEM-30 Betriebsanleitung

Onicon

Onicon F-1000 SERIES Bedienungsanleitung

Onicon

Onicon F-1000 SERIES Konfigurationshandbuch

Onicon

Onicon FT-3400 Betriebsanleitung

Onicon

Onicon F-4600 Series Betriebsanleitung

Onicon

Onicon SYSTEM-30 Betriebsanleitung

Onicon

Onicon D-100 Betriebsanleitung

Onicon

Onicon SYSTEM-1000 Betriebsanleitung

Onicon

Onicon SeaMetrics EX90 Bedienungsanleitung

Onicon

Onicon System-10 BTU Meter Betriebsanleitung

Onicon

Onicon F-4300 Original Betriebsanleitung

Onicon

Onicon D-100 Bedienungsanleitung

Onicon

Onicon F-4400 Bedienungsanleitung

Onicon

Onicon D-100 Bedienungsanleitung

Onicon

Onicon System-10 BTU Meter Bedienungsanleitung

Onicon

Onicon System-10 BTU Meter Bedienungsanleitung

Onicon

Onicon F-5100 Inline Betriebsanleitung

Onicon

Onicon FT-3400 Betriebsanleitung

Onicon

Onicon F-5000 Betriebsanleitung

Onicon

Onicon F-3100 Series Montageanleitung

Onicon

Onicon F-1000 SERIES Bedienungsanleitung

Onicon

Onicon SYSTEM-30 Betriebsanleitung

Onicon

Onicon D-100 Betriebsanleitung

Onicon

Onicon FT-4600 Betriebsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung