Opitec Wind Machine Bedienungsanleitung

100.803

Wind Machine

Required Tools:

Please Note

The Opitec Range of projects is not intended as play toys for young children. They are

teaching aids for young people learning the skills of craft, design and technology. These

projects should only be undertaken and operated with the guidance of a fully qualified

adult. The finished projects are not suitable to give to children under 3 years old. Some

parts can be swallowed. Danger of suffocation!

Jigsaw

Parts List Quantity Size (mm) Description Part No.

Cork board (pre-stamped) 1 250x125x4 Pre-stamped parts 1

Coloured card 1 210x150 Forms 2

Card board (pre-stamped parts) 1 195x155 Pre-stamped parts 3

Round rod 6 ø3x300 Round rods 4

Metal eyelet 4 ø4/3 Bearing 5

Sandpaper 1 Sandpaper 6

Superglue 1 Glue 7

Veneer 1 Wind blades 8

Wooden sticks 1 pack Wooden sticks 9

Scissors Ruler

Pencil Craft KnifePrickling Awl

Craft Knife Pliers

Instructions 100.803

Wind Machine

Carefully remove the pre-stamped parts (a-G) from the cork board (1). Cut out the carboard connectors (2a+2b) and carefully scratch the fold

lines with the tip of the scissors.

Glue the cardboard connectors (2a) to the cork base part (A) with the

superglue. Connect them together as shown.

Shorten 2 rods (3) to a length of 250 mm. Then glue them into the

corners of the base with the superglue as shown. Note: The rod tip

faces up.

33a

Remove the pre-stamped parts (3a-3f) from the cardboard sheet.

Glue the ﬁnished base centered on the cardboard part (3g).

Glue the ﬁnished upper part of the tower between the round bars as

shown.

Glue the craft sticks (9) horizontally to the rods according to the

dimensions shown.

Note: Gradually adjust lenghts.

Then glue diagonal sticks between the horizontal sticks as shown

above.

Note: Gradually adjust lengths.

To ﬁnish the tower, glue on more sticks rotated by 90°.

Glue the cardboard connectors (2b) to the cork part (B) with the superglue as shown. Glue a metal eyelet (5) in the cardboard part (3e), glue the cork

walls around the cardboard part (3e) and connect them together. To ﬁnish, insert a metal eyelet (5) from above into the cork part (C) and glue on

centered.

Instructions 100.803

Wind Machine

Glue the three cardboard discs (3b, 3d and 3f) on top of each other as

shown, so that the holes are exactly aligned.

Cut four pieces of equal length (46 mm) from a round rod (4) and

clean up the saw cuts. Flatten the ends of the rods with pliers before

inserting them between the discs.Then, oset by 90°, glue them ﬂush

to the intermediate disc.

Glue the discs with the rods in the cardboard part (3a) in the recesses

provided.

Glue the two cork discs (D+E) centered on the wheel from both sides.

Cut a piece (75 mm) from a round rod (4). Clean the saw cuts and then

glue it in the hole of the cork disc (E).

Glue 2 metal eyelets (5) to the cork part (F). Then glue the cork disc (G)

centered from below. Push the ﬁnished bracket onto the rod as shown.

To ﬁx the turbine axle, glue a strip of paper approx. 5 mm wide and

60-80 mm long around the end of the axle.

Instructions 100.803

Wind Machine

Cut out the blades from the cardboard (2) or transfer the dimensions

to the wooden veneer (8). Then carefully cut out of the veneer with a

craft knife.

Glue 16 blades (depending on the version) into the wind wheel as

shown.

Cut a 150 mm long piece of round rod and glue on the wind blade (3c)

centered, as shown. Place the stick with the wind blade on the wind

machine bracket with glue.

Then glue a 65 mm long round rod into the hole of the cork part (G)

from below.

Insert the ﬁnished wind turbine into the upper part of the tower as

shown.

Done!

Instructions 100.803

Wind Machine

Dieses Handbuch passt für folgende Modelle

Andere Opitec Spielzeug Handbücher

Opitec

Opitec 114.066 Bedienungsanleitung

Opitec

Opitec 104.689 Bedienungsanleitung

Opitec

Opitec 102.320 Nummer II Bedienungsanleitung

Opitec

Opitec 106.809 Bedienungsanleitung

Opitec

Opitec 114.033 Bedienungsanleitung

Opitec

Opitec Hobbyfix Flip Bedienungsanleitung

Opitec

Opitec Easy-Line Wind Generator Bedienungsanleitung

Opitec

Opitec Hobbyfix 101.706 Bedienungsanleitung

Opitec

Opitec 115.305 Bedienungsanleitung

Opitec

Opitec Running worker with wheelbarrow Bedienungsanleitung

Opitec

Opitec Windflyer II Bedienungsanleitung

Opitec

Opitec Wasp Bedienungsanleitung

Opitec

Opitec Solar Auto with gearbox Bedienungsanleitung

Opitec

Opitec 117167 Bedienungsanleitung

Opitec

Opitec Hobbyfix Bedienungsanleitung

Opitec

Opitec Dragonfly 102.894 Bedienungsanleitung

Opitec

Opitec Hobbyfix Cube Bedienungsanleitung

Opitec

Opitec 111.714 Bedienungsanleitung

Opitec

Opitec Hobbyfix Cloud Bedienungsanleitung

Opitec

Opitec Recycling Rowing Boat Bedienungsanleitung

Opitec

Opitec 112.994 Bedienungsanleitung

Opitec

Opitec MANITOU 101.200 Bedienungsanleitung

Opitec

Opitec 120.852 Bedienungsanleitung

Opitec

Opitec 113.141 Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Handbuch

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

Meccano

Meccano 15103 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung