Optex FlipX Series Bedienungsanleitung
FlipX series
Flexible Range Indoor Detector
Flexible Range Indoor Detector
FlipX series
ADVANCED MODELS
INSTALLATION INSTRUCTIONS
59-3112-0 2208-31
UL 59-3112-0 2110-01
EN
1
- Manufacturer's statement
- Parts identification
- Anti-masking
- Specifications
- Events and responses
- LED indications
- Dimensions
- Detection area
- Angle adjustment
with bracket CW-G2/CW-G3
- Compliance
Before installation
Others
<< Contents >>
Page
2
3
EOL settings
Down zone ON/OFF
Settings
2
Checking3
6
13
Volume setting
Wide/Narrow setting
Wide/Narrow area
Flip lens
PIR Anti-masking Microwave
FLX-A-AM ✓ ✓ ✓ -
FLX-A-DAM-X5
*1
✓ ✓ ✓ ✓(10.525 GHz)
FLX-A-DAM-X8
*2
✓ ✓ ✓ ✓(10.587 GHz)
FLX-A-DAM-X9
*3
✓ ✓ ✓ ✓(9.425 GHz)
*1 Not certified to INCERT, NF
*2 Not certified to UL and SBSC
*3 Not certified to EN 50131-2-4, NF, INCERT, SBSC and UL
Installation
Wall mount
without bracket
Wiring
1
Wall mount
with bracket
Ceiling mount
with bracket
Disassemble 4
8
5
10
7
3
12
12
11
14
15
15
16
17
17
17
DIP switch settings 12
Mounting height
2.0 to 3.0 m (6’7” to 9’8”)
2.4 m (8’) recommended
Warning
Caution
< 1 m
Wetting with water
[ FLX-A-DAM only ]
Destroy
modify
<1 m
Outdoor installation
Detection through glass
Face to face/Back interference
Partial/complete obscuration
of the detection area.
Follow to the regulations
- Manufacturer’ s statement
NOTE
Failure to follow the instructions provided with this indication
and improper handling may cause death or serious injury.
Failure to follow the instructions provided with this indication
and improper handling may cause injury and/or property damage.
Check mark indicates recommendation.
Nix sign indicates prohibition.
Special attention is required to the
section of this symbol.
Symbol Meaning
Warning
Caution
Symbol Meaning
Before installation
2
Options
Cover
Main unit
Base
- Parts identifications
3
Sponge
Lens
CW-G3 *: Bracket for wall/ceiling mount
with tamper switch
Accessories
Mount screw x 2
PEU: Plug-in EOL Unit
Do not touch PIR and MW units.
* Not certified to EN 50131-2-2/EN 50131-2-4,
INCERT and SBSC
- Anti-masking
Wall tamper screw x 1
Joint screw x 3
Fixing screw x 2
Overview of anti-masking
If the front of the lens is covered with obstacles over 20 seconds, an alarm and trouble will be output.
Sensitivity setting
(Refer to “2-3 Dip switch/Volume settings” - “ Anti-masking sensitivity” )
Normally, use it in “Middle” .
Select the “High” setting if required by any standards or sensitivity is insufficient.
If there are many false alarms, you can use “Low” , but please note that it may not be output depending
on the materials and colors of the obstacles.
5
4
1-1. Disassemble
Open the cover
Unlock the cover
Installation
1
180°
12
Remove the terminal block
3
Pull
the 2 stoppers alternately to
remove the terminal block.
4
You do not need to remove the terminal block
if it does not interfere with the mounting of the base.
NOTE
Mount the base
a. Wall mount b. Corner mount
Wire through the base
1-2. Wall mount without bracket
Wiring knockouts
For Wall mount
For Corner mount
Additional holes for tamper protect
for wall mount or
for corner mount
If the device is intentionally removed from the
mounting position, the brown colored part will
be cracked and remained on the wall.
The tamper switch will be operated.
For Wall/ Corner mount
Surface wiring
: Upper
: Lower
Mounting holes
A. Surface wiring
A-1. Upper A-2. Lower
B. Hidden wiring
How to break the knockouts
1
2
For Wall/ Corner mount
Hidden wiring:
Additional
Additional
5
Go toPage
8
6
1-3. Wall mount with bracket
Go to Page
8
Wire and mount on the wall
1
Wiring knockout guides
Punch out 3 knockout guides,
to open the wiring hole to allow
wiring run.
2Join the base on the bracket
Joint screw x 3
The bracket is basically jointed
using 3 holes and 3 joint screws.
Also use 2 additional fixing holes
if stronger support is required.
3Fix the base with the fixing screws
Fixing screw x 2
Adjust the detection direction while jointing.
Confirming with a walk test is required.
--> Refer to “3-1. Walk test”
NOTE
NOTE
See page 5 for how to break the knockouts.
Wiring knockout hole
7
How to change the bracket to the ceiling mounting
[1] Loosen the fixing screw. [2] Rotate the body. [3] Tighten the fixing screw.
1-4. Ceiling mount with bracket
Wire and mount on the ceiling
1
Joint screw x 3
Fixing screw x 2
The bracket is basically jointed
using 3 holes and 3 joint screws.
Also use 2 additional fixing holes
if a stronger fixation is required.
Adjust the detection direction while jointing.
Confirming with a walk test is required.
--> Refer to “3-1. Walk test”
NOTE
2Join the base on the bracket 3Fix the base with the fixing screws
WALL
WALL
Rear side
Rear side
CEILING
CEILING
NOTE
See page 5 for how to break the knockouts.
Wiring knockout guides
Punch out 3 knockout guides,
to open the wiring hole to allow
wiring run.
Wiring knockout hole
8
1-5. Wiring
Power Spare Trouble Common Alarm Tamper Remote LED *
* State not evaluated by UL
Wire to the terminal block
1
Attach the terminal block to the base
2
Insert the protrusions on both ends of the
terminal block into the holes in the base
(the parts shown in red).
WIRE GAUGE
AWG 22
(0.33 mm²)
AWG 20
(0.52 mm²)
AWG 18
(0.83 mm²)
12 V DC
360 m
(1,180 ft.)
570 m
(1,870 ft.)
900 m
(2,950 ft.)
14 V DC
780 m
(2,560 ft.)
1,230 m
(4,040 ft.)
1,960 m
(6,430 ft.)
WIRE GAUGE
AWG 22
(0.33 mm²)
AWG 20
(0.52 mm²)
AWG 18
(0.83 mm²)
12 V DC
270 m
(890 ft.)
430 m
(1,410 ft.)
690 m
(2,260 ft.)
14 V DC
590 m
(1,940 ft.)
940 m
(3,080 ft.)
1,490 m
(4,890 ft.)
FLX-A-AM
FLX-A-DAM
Power cable length
The power cable should be limited to the
following length.
SP TR COM AL TP TP LED
+
-
SP TR COM AL TP TP LED
+
-
SP TR COM AL TP TP LED
+
-
Twist and swage
the wires.
NOTE
How to wire to the tamper switch on the CW-G3.
9
Remove the main unit
1
2-1. Wide/Narrow setting
Change the Flip lens from “Wide” to “Narrow”
How to remove the lens
Get over the rib, then pull up the lens.
2
WIDE
NARROW
NOTE
Default
If it is difficult to get over, use a flat head screwdriver.
Caution
Be careful not to damage the lens with a screwdriver.
Install the lens so that the letters on the cover and on the lens
match your intention.
By changing the lens setting, the internal circuit automatically
switches between Narrow and Wide.
Opening the hooked part as the red arrows indicate
makes it easy to take out the main unit.
NOTE
Go to 2-2 on to skip 2-1
when using the default “Wide” setting.
Page
11
Settings
2
10
How to install the lens
Push the lens firmly at 3 points in numerical order.
1
23
By changing the lens, the internal settings of “Wide” and “Narrow” are automatically switched.
It is not necessary to change the settings such as DIP switches.
When the lens is set to the “Narrow” position, MW detection will be disabled automatically.
NOTE
Assemble
3
Andere Handbücher für FlipX Series
1
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere Optex Sicherheitssensor Handbücher
Optex
Optex Smart Line SL-350 QNR Bedienungsanleitung
Optex
Optex OVS-6000 Bedienungsanleitung
Optex
Optex REDSCAN PRO RLS-50100V Bedienungsanleitung
Optex
Optex Smart Line Series Bedienungsanleitung
Optex
Optex AP-20NB(C) Bedienungsanleitung
Optex
Optex OVS-50TNR Bedienungsanleitung
Optex
Optex HX-40 Bedienungsanleitung
Optex
Optex REDWALL-V Leitfaden
Optex
Optex Smart Line Series Bedienungsanleitung
Optex
Optex OA-PRESENCE TN Bedienungsanleitung
Optex
Optex REDSCAN mini-Pro Series Bedienungsanleitung
Optex
Optex FX-50QZ Bedienungsanleitung
Optex
Optex AX-350DH MK III Bedienungsanleitung
Optex
Optex WX Shield Series Bedienungsanleitung
Optex
Optex OVS-01CC Bedienungsanleitung
Optex
Optex Fiber SenSys Laser Defender LD308SH Montage- und Bedienungsanleitung
Optex
Optex BX SHIELD Series Bedienungsanleitung
Optex
Optex VX-402R Bedienungsanleitung
Optex
Optex VX Infinity Series Bedienungsanleitung
Optex
Optex OA-FUNXION Bedienungsanleitung
