Orange Electronic P451 Bedienungsanleitung
Manual for Tire Pressure Monitoring Systems, TPMS
1/24
TABLE OF CONTENTS
TIRE PRESSURE MONITORING SYSTEM, TPMS.................................... 2
NOTICE........................................................................................... 2
SPECIFICATIONS OF TPMS................................................................ 3
ACCESSORIES .................................................................................. 4
SYSTEM INSTALLATION.................................................................... 5
DISPLAY UNIT INSTALLATION ........................................................... 5
WIRELESS TRANSMITTER SENSOR INSTALLATION............................... 7
SYSTEM OPERATION...................................................................... 11
SYSTEM ALARM ............................................................................ 11
SETTING ....................................................................................... 11
Choose to read Tire Pressure Or Temperature.......................................................................... 12
Standard Front/Rear Tire Pressure Setting ............................................................................... 13
Tire Over Temperature Warning .............................................................................................. 14
Alarm Instruction.................................................................................................................... 14
RESET FOR TIRE CHANGE AND ROTATION ....................................... 16
Mode 1: Replace 4 Sensors ...................................................................................................... 17
Mode 2: Replace Single Sensor ............................................................................................... 18
Mode 3: OTO (Orange Tire Orientation Technology) Settings .................................................... 19
APPENDIX 1 .................................................................................. 20
APPENDIX 2 .................................................................................. 21
WARRANTY POLICY ....................................................................... 22
TROUBLESHOOTING GUIDE............................................................ 23
To ensure correct operation and service, please read these
instructions before installing and operating the TPMS.
Manual for Tire Pressure Monitoring Systems, TPMS
2/24
TIRE PRESSURE MONITORING SYSTEM, TPMS
Tire Pressure Monitoring Systems (TPMS) improves safety while driving. Once installed in your
vehicle, the system will automatically monitor your tires in real-time for pressure and temperature.
If any tire’s pressure and/or temperature appears abnormal, the system will, in real-time,
transmit signals to activate an alarm and show a digital figure to warn the driver of a problem. The
system aids safety, extend the tire life and help reduce fuel consumption.
NOTICE
FCC Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the factoring measures.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
Caution
Any changes or modifications in construction of this device which are not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
To comply with the FCC RF exposure compliance requirements, this device and its antenna must not be
co-located or operating to conjunction with any other antenna or transmitter.
System Scope of Use and Warnings
Tire Pressure Monitoring System, TPMS
This system is a sensing device designed to measure and display tire operation and / or activate an alert to
the driver when pressure and temperature irregularities are detected. It is the responsibility of the driver
to react promptly and with discretion to alerts. Abnormal tire inflation pressure should be corrected at
the earliest opportunity.
Caution
The system is wireless RF product; therefore, it may not receive signal due to interference environment or
incorrect operating or installation. When the system continually cannot receive signal from one of the tire
sensor more than 20 minutes since the system be switched on, the system will show “ E2 ”. In this case, it
may cause by a RF interference environment and driver needs to drive the vehicle to other place. If the
display still cannot receive any correct signal from tire sensor, then, driver needs to find a nearby qualified
tire maintain service for checking and maintain. It may cause by a tire sensor damaged or battery power
consumption is low (the battery consumption will be lower than under normal using condition due to
sensors need to send warning signal continually to driver) . If the system continually cannot receive signal
from any sensors more than 20 minutes, the system might damaged and will show “E1”. Driver needs to
drive to other place (there might be a interference nearby) or send the system
to agent for repair.
Manual for Tire Pressure Monitoring Systems, TPMS
3/24
System Installation and Usage
The installation of TPMS requires the qualified personnel to operate according to the instruction manual
so that it can function properly and have the warranty.
Warranty does not cover damages due to improper installation or disassembly.
This system is only suitable for Pick-up tires. The standard tire pressure is 20psi-110psi.
The maximum pressure the sensor can read is 116 psi (gauge). This system is not suitable for iron rim.
※In order to prevent the air leaking issues, it is strongly suggested that the valve has to be checked or
replaced on a regular basis.
Reaction to Alerts
When an alert or warning is received, reduce vehicle’s speed and pull over to a safe location where the
tire can be inspected and /or serviced.
The low-pressure alert indicates that the air pressure has dropped to a selected minimum and a
high-temperature alert indicates that the temperature of the tire content has surpassed the
threshold value set.
Use Of Chemicals
Temporary resealing or re-inflation products containing internal sealants or propellants in any tire
assembly may adversely affect the operation of the sensor/transmitter.
PLEASE RECYCLE THE BATTERIES
SPECIFICATIONS OF TPMS
RECEIVER SPECIFICATIONS
Operating Voltage
5V DC
Operating Current
< 150mA
Storage Temperature
-30oC to 75oC
Operating Temperature
-25oC to 75oC
TRANSMITTOR SENSOR SPECIFICATIONS
Storage Temperature
-40oC to 125oC
Operating Temperature
-40oC to 125oC
Operating Humidity
MAX. 95%
Operating Frequency
433.92MHz ± 50kHz
Pressure Monitoring Range
0~116 psi
Pressure Reading Accuracy
Under normal condition
± 1psi at normal pressure range
Temperature Reading Accuracy
± 4oC under normal condition
Transmission Power
MAX. 73.5 dBμV/m
Battery
3V
Weight
28g ± 3g
Manual for Tire Pressure Monitoring Systems, TPMS
4/24
ACCESSORIES
No.
Image
Description
Q’ty
A
Wireless Receiver and Display
Unit
1
B
Velcro for Display
3
C
3M Double-coated Adhesive
1
D
Power Cord
(with 90 degree Micro-USB;
300cm in length)
1
E
Power Connector for Cigarette
Lighter (USB with 2 outputs)
1
F
Windshield Holder (Nut included)
1
G
Base for Display
1
H
Base (Adhesive to Windshield)
1
I
Wireless Transmitter Sensor
(Remote Sensing Module) with Tire
Valve Cap
4
Manual for Tire Pressure Monitoring Systems, TPMS
5/24
SYSTEM INSTALLATION
The Tire Pressure Monitoring System is composed of 2 parts:
1. The display, which is put in inside the vehicles.
2. The transmitter sensors, which are installed in the tires.
We strongly suggest installing the display unit first, and then install the 4 transmitter sensors.
Warranty including “Wireless Display Unit and Wireless Transmitter Sensor and Power
Connection cable”, not including other accessories.
Note When you remove the transmitter sensors to different tires and replace new transmitter sensors,
it is suggested to change all of the valve stems and screws.
Note Please use the original charger to maintain the good performance.
DISPLAY UNIT INSTALLATION
1. Adhere one Velcro (B) to the backside of the Wireless Receiver and Display Unit (A). Adhere
another Velcro (B) to Base (G).
2. Plug Power Cord (D) into Micro USB input of Wireless Receiver and Display Unit (A).
3. Connect Power Cord (D) to any input of Power Connecter (E). Plug another end
into the Cigarette Lighter of the vehicle.
4. Choose a position on windshield to fix the Display. As the following,
you may see Base (G) and Display (A) are attached by two Velcros (B).
5. Remove the protection film on the Display (A).
Option A: Use the Windshield Holder
Step1: Adhere Velcro (B) to the Display’s Base (G).
Step2: Assemble the Nut (F) to the (G)
Step3: Insert the ball head of (G) to the holder (F), and tighten the nut.
Step4: The assembly is completed as the below image.
G: Base for Display
B: Velcro
F: Windshield Holder
G: Base for Display
B: Velcro
F: Nut of Windshield
Holder
F: Windshield Holder
Manual for Tire Pressure Monitoring Systems, TPMS
6/24
Option B: Adhere to the windshield.
Step1: Adhere Velcro (B) to the Base (G).
Step2: Unscrew Nut from Windshield Holder (F) and fix it on Base (G).
Step3: Attach the head of the Base (G) into the Nut (F), and screw tightly.
Step4: Use any side of 3M double-coated Adhesive (C) to Windshield Holder (F), another side is
adhesive to windshield.
Step5: The assembly is completed as the below image.
C :雙面背膠黏貼處
B : Velcro
G: Base of Display
H :擋風玻璃黏貼支架
B: Velcro
G: Base for Display
F: Nut of Windshield
Holder
F: the hold that
attaches to the
windshield.
C: 3M Double-coated
Adhesive
Manual for Tire Pressure Monitoring Systems, TPMS
7/24
WIRELESS TRANSMITTER SENSOR INSTALLATION
Step
Process
Image
1
Use a jack to raise the vehicle and place jack stands
underneath the vehicle for safety. Refer to vehicle owner’s
manual for full service advice. Seek the assistance of a
qualified motor mechanic if required.
2
Take off the tires and bleed the air. Then take off the air
valve of the tire from the wheel. (NOTE: You must change
the valve to TPMS valve). This part of the process will
normally require the service of a tire fitting service or
mechanic.
3
Recognize the number on each sensor (D) with position of
tire on the vehicle. (VERY IMPORTANT)
a. RF –1 = Right Front, No. 1
b. RR –2 = Right Rear, No. 2
c. LR –3 = Left Rear, No. 3
d. LF –4 = Left Frtong, No. 4
4
Set up the new TPMS special valve (E) in the wheel.
Use wrench to fix the valve, and then tighten nut to
40~45kgf-cm (4~4.5Nm).
5
Clean inside the tire to prevent the tire from damaging the
transmitter sensor.
6
Inflate the tires.
Balance the tire
a. Balance tires using a balance machine
b. A lead tire weight may need to be added for balancing.
c. Balance until the tire balance shows balance as “OK”
Wireless
Transmitter Sensor
(with the valve)
bolt
Manual for Tire Pressure Monitoring Systems, TPMS
8/24
The steps above will require the assistance of a tire fitting
service or a mechanic. It is important that the wheels are
balanced after the fitting of the TPMS sensors in order to
ensure the safe operation of the tire when refitted to the
vehicle.
7
Set up the other three tires in the same manner.
8
Turn the ignition key of the vehicle until the power is
activated on the cigar lighter, this may be first or second
position depending on the car manufacturer. The in-car
display will be activated.
The function button of the display unit can be switched to
pressure or temperature depending on the customer’s
need.
Manual for Tire Pressure Monitoring Systems, TPMS
9/24
Manual for Tire Pressure Monitoring Systems, TPMS
10/24
Andere Handbücher für P451
1
Inhaltsverzeichnis
Andere Orange Electronic Messgerät Handbücher
