Oriental motor BXII Series Bedienungsanleitung
HP-5058-3
Data Setter OPX-2A
BXⅡ Series
OPERATING MANUAL
Thank you for purchasing an Oriental Motor product.
This Operating Manual describes product handling procedures and safety precautions.
Please read it thoroughly to ensure safe operation.
Always keep the manual where it is readily available.
Table of contents
1 Safety precautions ...............................2
2 Introduction ..........................................3
3 Preparation ..........................................4
3.1 Checking the product ............................ 4
3.2 Names and functions of parts ............... 4
3.3 How to read the display ......................... 5
3.4 How to read the LED indicators ............ 5
3.5 Types of operation modes ..................... 5
3.6 Basic operations of the OPX-2A ........... 6
3.7 Edit lock function ................................... 7
3.8 Rewriting the driver’s non-volatile
memory ................................................. 7
4 Installation and connection of the
OPX-2A ...............................................8
4.1 Location for installation ......................... 8
4.2 Installation method ................................ 8
4.3 Connecting to the driver ........................ 9
4.4 Error display on OPX-2A screen ........... 9
5 When using the product with the
speed control mode ...........................10
5.1 Screen transitions ............................... 10
5.2 Monitor mode ...................................... 14
5.3 Data mode ........................................... 18
5.4 Parameter mode ................................. 20
5.5 Test mode ............................................ 22
5.6 Copy mode .......................................... 25
6 When using the product with the
position control mode ........................28
6.1 Screen transitions ............................... 28
6.2 Monitor mode ...................................... 32
6.3 Data mode ........................................... 37
6.4 Parameter mode ................................. 38
6.5 Test mode ............................................ 39
6.6 Copy mode .......................................... 42
7 Parameter ..........................................43
Safety precautions
−2−
1 Safetyprecautions
The precautions described below are intended to prevent danger or injury to the user and other personnel through safe,
correct use of the product. Use the product only after carefully reading and fully understanding these instructions.
Also read the "Safety precautions" sections in the USER MANUAL that came with the product you are combining
with the OPX-2A.
Handling the product without observing the instructions that accompany a "Warning"
symbol may result in serious injury or death.
Handling the product without observing the instructions that accompany a "Caution"
symbol may result in injury or property damage.
Note
The items under this heading contain important handling instructions that the user should
observe to ensure safe use of the product.
General
Do not use the product in explosive or corrosive environments, in the presence of ammable gases, locations
subjected to splashing water, or near combustibles. Doing so may result in re, electric shock or injury.
Assign qualied personnel the task of installing, wiring, operating/controlling, inspecting and troubleshooting the
product. Failure to do so may result in re, electric shock or injury.
When the driver’s protective function is triggered, rst remove the cause and then clear the protective function.
Continuing the operation without removing the cause of the problem may cause malfunction of the motor and
driver, leading to injury or damage to equipment.
Repair, disassembly and modication
Do not disassemble or modify the data setter. This may cause electric shock or injury. Refer all such internal
inspections and repairs to the branch or sales ofce from which you purchased the product.
General
Do not use the motor, gearhead and driver in conditions exceeding the specications. Doing so may result in
electric shock, injury or damage to equipment.
Operation
Provide an emergency stop device or emergency stop circuit so that the entire equipment will operate safely in the
event of a system failure or malfunction. Failure to do so may result in injury.
Disposal
Dispose the product correctly in accordance with laws and regulations, or instructions of local governments.
Introduction
−3−
2 Introduction
Only qualied personnel should work with the product.
Use the product correctly after thoroughly reading the section "1 Safety precautions" on page.2.
The product described in this manual has been designed and manufactured to be incorporated in general industrial
equipment. Do not use for any other purpose. Oriental Motor Co., Ltd. is not responsible for any damage caused
through failure to observe this warning.
Overviewoftheproduct
The OPX-2A is a data setter that lets you set operation data and parameters, perform monitoring, etc.
Use the OPX-2A properly and safely after thoroughly reading the "BXⅡ Series USER MANUAL" and understanding
the basic operating procedures and other details.
FeaturesofOPX-2A
The OPX-2A can be used to save data in addition to setting of operation data and parameters.
There are four destinations (data banks) to save data.
OPX-2A
Data bank 1
Data bank 0
Data bank 2
Data bank 3
Driver
Driver
Set operation data and parameters.
Up to 4 sets of operation data and
parameters can be saved.
Copy any one of the four
sets to the driver.
The OPX-2A can be used for the following purposes:
Operation data and parameters of the driver can be set.
The operating status of the motor can be monitored.
Operation data and parameters set in the driver can be saved to the OPX-2A.
Operation data and parameters saved in the OPX-2A can be copied to other drivers.
Specications
Connection Mini DIN, 8 pins
External dimensions 96 (W)×72 (H)×21.5 (D) mm
[3.78 (W)×2.83 (H)×0.85 (D) in.]
Cable length 5 m (16.4 ft.)
Mass 0.25 kg (8.8 oz)
RoHSDirective
The products do not contain the substances exceeding the restriction values of RoHS Directive (2011/65/EU).
Preparation
−4−
3 Preparation
This chapter explains the items you should know before using the OPX-2A.
3.1 Checkingtheproduct
Verify that the items listed below are included. Report any missing or damaged items to the branch or sales ofce
from which you purchased the product.
Data setter OPX-2A...................................... 1 unit
Information ................................................... 1 copy
3.2 Namesandfunctionsofparts
Display
This area shows the motor position,
operation data, parameters, alarms, etc.
LED indicators
These LED indicators are used to indicate
the operation mode of the OPX-2A and
the driver status.
Use this button to select data or change
the displayed item or move to the lower
level.
Use this button to change the operation
mode or move to the upper level.
Use these buttons to change the selected item or set data and parameters.
Use these buttons to increase or decrease the value or change the selected item.
Use these buttons to navigate through each data or parameter to a desired digit.
Notation
In this manual, keys are denoted by symbols, such as .
In gures, a simplied illustration of the display and LED indicators is used, as shown below.
Preparation
−5−
3.3 Howtoreadthedisplay
The display consists of 7-segment LEDs. (The number "5" and alphabet "S" are the same.)
1234567890
A
• Numbers
+
-
• Signes
• Alphabets
B C D E F G H I J K L
M N O P Q R S T U V W Y
3.4 HowtoreadtheLEDindicators
When the operation mode is changed or an alarm or warning generates, a corresponding LED will be lit.
While the motor is operating or the edit lock function is enabled, the condition is also indicated by the illumination of
a corresponding LED.
Lit in the copy mode
Lit in the test modeLit in the parameter mode
Lit in the data mode
Lit in the monitor mode
Lit while an alarm is present
Lit while a warning is present
Lit while the motor is operating Not used
Lit while the edit lock function is enabled
Not used
Not used
3.5 Typesofoperationmodes
The OPX-2A has multiple operation modes. The operation
mode will change every time the key is pressed.
The display starts in the monitor mode when the power is
turned on.
When the operation mode is changed, the LED indicator
corresponding to the previous mode will turn off and the one
corresponding to the new mode will be lit. Identify the present
operation mode based on the LED indicator currently lit.
Monitor mode
(MON)
Copy mode
(COPY)
Test mode
(TEST)
Parameter mode
(PAR)
Data mode
(DATA)
The mode changes
every time the key
is pressed.
Preparation
−6−
3.6 BasicoperationsoftheOPX-2A
Use the six keys to set data and operate the motor.
Operationow
The OPX-2A is operated according to the ow shown below.
Level 2: Item selection screen Level 3Level 1: Top screen in each mode
12
3
4
Use the
key to navigate
through the
modes.
Use the
key to move
to the lower level.
toUse
move to the
previous item.
toUse
move to the
next item.
Use the
key to move
to the upper level.
1. Use the key to select a desired operation mode appropriate for your intended operation.
Example: If you want to use a function in the test mode, press the key to select the test mode (indicated by
a lit "TEST" LED).
The top screen of the test mode is displayed.
2. Press the key to move to the lower level.
3. Use the keys to select a desired item.
4. To move to the lower level, press the key. To return to the previous level, press the key.
As explained above, use the key to navigate through the levels and use the keys to select a desired
item. This is the basic operation ow.
Note If the key is pressed while the driver performs the internal processing, the screen cannot
change to any lower level from the top screen, and "mEm-bUSY" is displayed.
Be sure to wait until all internal processing is completed, before pressing the key.
Preparation
−7−
Howtoinputvalues
As an example, how to change the rotation speed from "80" r/min to "1000" r/min is explained.
Basic operations
Use the keys to increase/decrease the value or change the sign. Use the keys to move to the
digit you want to edit.
If positive and negative values are differentiated, each value is preceded by a sign.
The digit currently blinking can be edited.
1. First, change the 10’s place from "8" to "0."
Press the key once to move to the 10’s digit you want to edit.
Determined
Once
Twice
Twice
Once
2. Press the key twice to change the value to "0."
3. Next, change the 1000’s place from "0" to "1."
Press the key twice to move to the 1000’s digit you want to edit.
4. Press the key once to change the value to "1."
5. After all digits have been changed, press the key to
determine the value.
All digits comprising the value blink for approximately 2 seconds.
Note If the value you have input is outside the setting range, "Error" will be displayed for 1 second. If this error
display appears, input a different value that falls within the setting range.
3.7 Editlockfunction
Enable the edit lock function if you want to prevent operation data and parameters from being edited or cleared.
Operation data and parameters cannot be changed or deleted while the edit lock function is enabled.
Setting the edit lock function
Press the key for at least 5 seconds on the top screen in each
mode.
The display will show "LocK" and the edit lock function will be
enabled.
The "LOCK" LED in the LED indicator area will also be lit.
"LOCK" lit
Canceling the edit lock function
Again, press the key for at least 5 seconds on the top screen in
each mode.
The display will show "UnLocK" and the edit lock function will be
cancelled.
The "LOCK" LED in the LED indicator area will turn off.
3.8 Rewritingthedriver’snon-volatilememory
Operation data and parameters are saved to the driver’s non-volatile memory. The non-volatile memory can be
rewritten approximately 100,000 times. The non-volatile memory will be rewritten after one of the following
operations is performed:
Edit any operation data or parameter
Download data from the OPX-2A to the driver
Initialize driver operation data and parameters
Installation and connection of the OPX-2A
−8−
4 Installationandconnectionofthe
OPX-2A
4.1 Locationforinstallation
The OPX-2A is designed and manufactured to be incorporated in equipment.
Install it in a well-ventilated location that provides easy access for inspection. The location must also satisfy the
following conditions:
Inside an enclosure that is installed indoors (provide vent holes)
Operating ambient temperature 0 to +40 °C (+32 to +104 °F) (non-freezing)
Operating ambient humidity 85% or less (non-condensing)
Area that is free of explosive atmosphere or toxic gas (such as sulfuric gas) or liquid
Area not exposed to direct sun
Area free of excessive amount of dust, iron particles or the like
Area not subject to splashing water (rain, water droplets), oil (oil droplets) or other liquids
Area free of excessive salt
Area not subject to continuous vibration or excessive shocks
Area free of excessive electromagnetic noise (from welders, power machinery, etc.)
Area free of radioactive materials, magnetic elds or vacuum
1000 m (3300 ft.) or less above sea level
4.2 Installationmethod
Using a metal plate of 1 to 3 mm (0.04 to 0.12 in.) in thickness, insert the OPX-2A into the mounting hole from the
front side and securely attach it.
92 +0.8
0 (3.62 )
+0.031
0
68 +0.7
0
(2.68 )
+0.028
0
• Dimension of mounting hole [mm (in.)]
Removing method
Press all of the four hooks provided on top and bottom of the OPX-2A.
In this condition, press the OPX-2A forward to release.
Hook
Installation and connection of the OPX-2A
−9−
4.3 Connectingtothedriver
Plug the connector attached to the end of the OPX-2A
cable into the data edit connector (CN6) on the driver, and
then turn on the power to the driver. Data edit connector
(CN6)
Note
When operation data and parameters are set on the OPX-2A, they will be stored in the driver.
Once stored in the driver, the data will not be cleared even after the OPX-2A is disconnected
from the driver.
Turning on the power to the driver will also turn on the power to the OPX-2A. Turning off the
driver power will turn off the OPX-2A power.
Turn off the driver power before connecting or disconnecting the OPX-2A cable.
4.4 ErrordisplayonOPX-2Ascreen
The following error message is displayed on the OPX-2A screen.
Error display Description Remedial action
A communication error occurred
between the OPX-2A and driver.
Check if the OPX-2A is connected securely.
Check if the OPX-2A cable is disconnected or
damaged.
The OPX-2A or the communication part of the driver
may have damaged. Contact your nearest Oriental
Motor sales ofce.
When using the product with the speed control mode
−10−
5 Whenusingtheproductwiththe
speedcontrolmode
5.1 Screentransitions
Speed
Load factor
Operation data number
Warning
I/O monitor
Monitor mode
Top screen
Input monitor
Output monitor
External voltage monitor
Warning record 1 (latest)
Warning record 10 (oldest)
Clear warning records
Alarm
Alarm record 1 (latest)
Alarm record 10 (oldest)
Alarm reset
Clear alarm records
Execute
(blinking)
Execute
(blinking)
Execute
(blinking)
Control mode
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Oriental motor Controller Handbücher
Oriental motor
Oriental motor DRL Series Bedienungsanleitung
Oriental motor
Oriental motor CRD5103P-RS4 Bedienungsanleitung
Oriental motor
Oriental motor AGL5H18 Series Bedienungsanleitung
Oriental motor
Oriental motor CRD514-KD Betriebsanleitung
Oriental motor
Oriental motor Astep AZ Series Bedienungsanleitung
Oriental motor
Oriental motor DRL Series Bedienungsanleitung
Oriental motor
Oriental motor TM Series Bedienungsanleitung
Oriental motor
Oriental motor aSTEP AZ Series Bedienungsanleitung
Oriental motor
Oriental motor DG Series Bedienungsanleitung
Oriental motor
Oriental motor a STEP ARL Series Bedienungsanleitung
Oriental motor
Oriental motor CM10 Series Bedienungsanleitung
Oriental motor
Oriental motor DSC Series Bedienungsanleitung
Oriental motor
Oriental motor ES01 Bedienungsanleitung
Oriental motor
Oriental motor DRLII Series Bedienungsanleitung
Oriental motor
Oriental motor FSC-24 Bedienungsanleitung
Oriental motor
Oriental motor EMP400 Series Bedienungsanleitung
Oriental motor
Oriental motor DRL Series Bedienungsanleitung
Oriental motor
Oriental motor EAS Series Bedienungsanleitung
Oriental motor
Oriental motor DR Series Bedienungsanleitung
Oriental motor
Oriental motor DRLII Series Bedienungsanleitung
