Outback Hunter THG3302PD Bedienungsanleitung
Photographs are not to scale.
Specifications subject to change
without prior notice.
Assembly and Operating Instructions for Outback®
Hunter 3 Burner Gas BBQ
WARNING
For outdoor use only. Not for commercial use.
Read instructions before using the appliance. Failure to follow instructions could
result in death, serious bodily injury, and/or property loss.
Warning: accessible parts may be very hot. Keep young children and pets away.
Do not move the appliance during use.
Turn off the gas supply at the gas bottle after use.
Any modification of the appliance, misuse, or failure to follow the instructions may be
dangerous and will invalidate your warranty. This does not affect your statutory rights.
Retain these instructions for future reference.
Leak test annually, and whenever the gas bottle is removed or replaced. Check that the
hose connections are tight and leak test each time you reconnect the gas bottle.
For Flare-up control please refer to the ‘OPERATION’ section of this manual.
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open barbecue lid or hood.
4. If odour continues, discontinue use and
contact your local dealer.
FOR YOUR SAFETY
1. Do not store or use petrol or other flammable
vapours or liquids in the vicinity of this or any
other appliance.
2. A gas bottle not connected for use shall not be
stored in the vicinity of this or any other
appliance.
0359
THG3302PD
2
Parts List
Quantities vary according to model purchased. Specifications subject to change without prior notice. For
more details on hardware, please see ‘Hardware Reference Diagram’.
CODE PART QTY Outback® Hunter 3 Burner
Gas BBQ
HOOD
A1 Hood (Pre-Assembled to Body) 1
A2 Hood Handle 1
A3 Heat Indicator 1
A4 Warming Rack 1
BODY
B1 Barbecue Body 1
B2 Burner 3
B3 Control Panel 1
B4 Knob 3
B5 Flame Tamer 3
B6 Cooking Grill 2
B7 Drip Tray 1
B8 Drip Tray Left Bracket 1
B9 Drip Tray Right Bracket 1
B10 Hose and Regulator Assembly 1
B11 Charcoal Basket 1
TROLLEY
C1 Left Side Shelf 1
C2 Right Side Shelf 1
C3 Left Front Leg 1
C4 Left Rear Leg 1
C5 Right Front Leg 1
C6 Right Rear Leg 1
C7 Screen 1
C8 Trolley Base 1
C9 Leg Endcap 2
C10 Axle 1
C11 Wheel 2
C12 Wheel Hubcap 2
HARDWARE
D1 M5x15 Bolt 4
D2 Washer 4
D3 M5 Nut 4
D4 M6x110 Bolt 8
D5 Spacer 8
D6 M6x25 Bolt 16
D7 M6x15 Bolt 8
D8 Axle Washer 2
D9 Locknut 2
Pre-Assembled Component
3
Parts Diagrams
Quantities vary according to model purchased. Specifications subject to change without prior notice. For
more details on hardware, please see hardware pack page.
B3
C1
C3 C6
C10
C11C12
C9
C4 C5
B8
B10 B4
B9
A1
C8
B6
C2
B2
D8
D9
A4
A3
A2
B1
B5
C7
B7
B11
4
Hardware Reference Diagram
Specifications subject to change without prior notice.
D1,D2,D3
D6
D4,D5
D7
5
2
Assembly
IMPORTANT!
TOOLS NEEDED FOR ASSEMBLY: Medium size flat blade or Phillips/Crosspoint screwdriver,
adjustable spanner or metric spanner set.
Remove any internal components or packaging from the barbecue body.
Whilst every care is taken in the manufacture of this product, care must be taken during assembly in
case sharp edges are present.
Please read the Important Information section carefully before assembly and use of your
barbecue.
1
Attach the Trolley Base (C8) onto the Left Front Leg (C3) and Right Front Leg (C5) using the
M6x15 Bolts (D7x4pcs) as shown.
C5
C8
C3
D7
Attach the Left Rear Leg (C4) and Right Rear Leg (C6) to the Trolley Base (C8) using the
M6x15 Bolts (D7x4pcs) as shown.
C8
C6
C4
C3 C5
D7
6
4
3
Unscrew the Locknuts (D9) from both ends of the Axle (C10) and remove the Axle Washers
(D8). Slide the axle through the corresponding holes in the left legs. Place axle washers on
each end of the axle. Slide the Wheels (C11) over each end of the axle. Secure the wheels
into place with the locknuts. Place the Wheel Hubcaps (C12) onto the outsides of the wheels.
Attach the Left Side Shelf (C1) and Right Side Shelf (C2) onto left and right legs using the
M6x25 Bolts(D6x16pcs) .
C11
C10
D9 C12 D8
C2
C1
7
Insert M6x110 Bolts (D4x8pcs) through the trolley legs, the Spacers (D5x8pcs), and keep the tip of
the bolts inside the spacers. While holding the barbecue body into position (2 people required),
screw the bolts into the barbecue body as shown.
CAUTION! Care must be taken to ensure the hood or lid does not fall open unexpectedly or
becomes damaged when it is set on the ground.
When positioning the body of the barbecue, ensure the control panel is on the same side as the legs
with Velcro fastenings.
6
5
Attach Drip Tray Left Bracket (B8) to barbecue body using M5x15 Bolts (D1x2pcs), Washers
(D2x2pcs) and M5 Nuts (D3x2pcs) as shown. Repeat above process for Drip Tray Right
Bracket (B9).
NOTE: Ensure that the big tabs of the brackets which stop the drip tray are located at
the front of the barbecue.
B8 D1,D2,D3
Rear view
Front view
D4
D5
8
8
7
Insert the Drip Tray (B7) by sliding it underneath the barbecue body.
Place the Flame Tamers (B5) over left and middle burners within barbecue body. Lay the Cooking
Grills (B6) in position.
NOTE: Ensure that the flame tamers lies directly underneath the grills.
B5
B6
B7
9
10
9
(Rear view of the barbecue trolley.)
Attach the screen (C7) to the front left/right legs as shown.
Attach the Warming Rack (A4) to barbecue body as shown. Make sure that the swing legs fix to
the body of the barbecue and the shorter fixed legs go through the holes in the hood.
C7
A4
Step 1
Step 2
Step 3
Step 4
10
Leak Test Diagram
ASSEMBLY IS NOW COMPLETE.
PROCEED TO THE NEXT PAGE FOR INSTRUCTIONS ON OPERATION AND
MAINTENANCE
ALL JOINTS AND CONNECTIONS MUST NOW BE LEAK TESTED BEFORE USING THE
BARBECUE.
Leak test annually, and whenever the gas bottle is removed or replaced.
Leak Testing
Always perform a leak test in a well-ventilated area.
Step 1 - Confirm all control knobs are in the off position.
Step 2 - Turn the gas on / open the gas control valve on the gas bottle or regulator.
Step 3 - Check for leaks by brushing a solution of ½ water and ½ liquid detergent / soap over all the
gas system joints, including gas bottle valve connections, hose connections, and regulator
connections.
Step 4 - NEVER USE AN OPEN FLAME to test for leaks at any time.
Step 5 - If bubbles form over any of the joints there is a leak
Turn off the gas supply at the gas bottle
Retighten all joints
Repeat test
If bubbles form again do not use the barbecue and contact your local distributor for assistance.
Always wipe the mixed solution (½ water and ½ liquid detergent / soap) from all joints and
connections after leak testing.
1. Maximum diameter or breadth is 320mm.
2. Maximum height (regulator included) is 700mm.
2
1
Inhaltsverzeichnis
Andere Outback Grill Handbücher
Outback
Outback Ranger 3 Bedienungsanleitung
Outback
Outback Cook Dome 703 Charcoal Bedienungsanleitung
Outback
Outback THG3302PC Bedienungsanleitung
Outback
Outback Orion Bedienungsanleitung
Outback
Outback Excel 100 Bedienungsanleitung
Outback
Outback THG3302P Bedienungsanleitung
Outback
Outback Omega 250 Bedienungsanleitung
Outback
Outback Omega 100 Bedienungsanleitung
Outback
Outback Omega Charcoal 100 Bedienungsanleitung
Outback
Outback Excel 100 Bedienungsanleitung
Outback
Outback Meteor MT-H4461-3 Bedienungsanleitung
Outback
Outback Meteor 3 Bedienungsanleitung
Outback
Outback Trooper Bedienungsanleitung
Outback
Outback Party Select 6 Burner Gas BBQ FS5680 Bedienungsanleitung
Outback
Outback Jupiter RS4491H Bedienungsanleitung
Outback
Outback RC4340S Bedienungsanleitung
Outback
Outback THG2302P-3 Bedienungsanleitung
Outback
Outback Spectrum 2 Burner Bedienungsanleitung
Outback
Outback Sapphire THG3216AW Bedienungsanleitung
Outback
Outback Mayfair Bedienungsanleitung
